Search NASA⌕ Search

Engineering topics

Xiao, Chuanxiao

Publications and source records attributed to Xiao, Chuanxiao.

60 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Nanometer-Scale Imaging of Inhomogeneous Active Charge Carriers in Arsenic-Doped CdTe Thin Films

We report nanometer-scale imaging of active carrier distribution of As-doped CdTe films by scanning capacitance microscopy (SCM). We developed SCM sample preparation for CdTe by ion-milling followed by thermal processing. The nanometer-resolution carrier delineation for CdTe was validated by imaging on a CdTe cross-section sample made by a molecular beam epitaxy layer stack with As-doping concentrations of 10^15 ~10^18 /cm 3 . We found that the carrier distribution in As-doped films was significantly nonuniform, with inhomogeneity ranging from sub-um to a few um and concentration variation of one order of magnitude (low 10^16 to low 10^17 /cm 3 ). This nonuniformity is distributed randomly, independent of grain structure and grain boundary (GB). We used Kelvin probe force microscopy (KPFM) and cathodoluminescence (CL) to further map the surface potential and radiative illumination on the same area as the SCM image. Higher potential and lower CL intensity were found on GBs but not on SCM contrast, illustrating positive GB charging and GB recombination but not GB-distinguished doping. The overall KPFM potential image is in rough agreement with the SCM carrier distribution, in terms of Fermi-level position relative to the bandgap edge - thus resulting in the band-edge potential fluctuation. Nonuniform carrier concentration, potential fluctuation, and defect recombination can all together cause the Voc deficit of the As-doped CdTe device.

14 SOLAR ENERGY↗
DOE OSTI2020

Operando Microscopy Characterization of Perovskite Solar Cells

In this work, we developed operando Kelvin probe force microscopy (KPFM) to study the electrostatic potential distribution across perovskite cells under light and forward bias to gain a deeper understanding of device operation physics. As a case study, we selected perovskite cells with a SnO 2 -based electron-selective layer (ESL), which showed great potential for fabricating high-efficiency, hysteresis-free devices due to the deeper conduction band and higher electron mobility of SnO 2 . The as-made device showed a main junction at the perovskite/spiro interface. After light soaking and applying forward bias, the junction quality improved, possibly explained by filling trap states at the interfaces and by the perovskite absorber perhaps having a self-poling effect; the main junction is observed at the ESL/perovskite interface. The results are consistent with current-voltage measurements, device performance improves mainly with fill factor enhancement. The operando KPFM results should more closely reflect the real case during current density-voltage measurements or solar cell operation. The operando KPFM technique that we have developed can be a powerful tool to provide a deeper understanding of the device operation mechanism and to further optimize the device.

14 SOLAR ENERGY↗
DOE OSTI2020

In-situ Microscopy Characterization of Cu(In,Ga)Se2 Potential-Induced Degradation

We report on the role of sodium in potentialinduced degradation (PID) of Cu(In, Ga)Se 2 (CIGS) solar cells. In-situ microscopy characterizations on AFM platform were performed on two stressed CIGS device under room temperature (RT) and high temperature (HT) at 85 degrees C. During PID stressing we observed depletion region gets wider as Na migrates, p-n junction becomes leaky at RT for over a month; and similar junction evolution was observed for HT-stressed sample, eventually the junction collapsed after 18 hours. The diode behaviors were confirmed by dark I-V measurement. Time-of Flight secondary-ion mass spectrometry reveals that the Na accumulates on ZnO and CdS side, as well as the upper layer of CIGS layer. The results indicate that Na drifted by the voltage applied on the soda-lime glass, then diffuse through the whole device. And the sodium profiles have different points of evolution due to the temperature differences between the two stressed samples. The consistent results unambiguously show how Na from substrate glass causes PID in CIGS solar cells.

14 SOLAR ENERGY↗
DOE OSTI2020

Decay of Electrostatic Force of Dust Particles on Photovoltaic Modules

Photovoltaic (PV) energy yield loss due to solar module soiling has become increasingly important as solar module deployment is now at the hundreds of gigawatts scale and continues to grow rapidly. We have reported on direct measurements-using atomic force microscopy (AFM)-of strong electric-field-induced attraction and adhesion force (Fes) of dust particles onto solar panel that are 1 to 2 orders of magnitude stronger than the van der Waals and water capillary forces, corroborated by observing the increase in system voltage-induced soiling rate. Here, we report another characteristic of Fes on soiling-long lasting or slow decay after turning off the high voltage applied to solar panels. The Fes decay time varies in a wide time range of 1 to 10 hours, depending on two factors: 1) either/both the cell or/and particle were charged with high voltage before the voltages were turned off; and 2) how the cell was connected to the ground after the voltage was turned off-either connected through the power supply electronics, directly connected to the ground, or electrically floated. The Fes decay is understood in terms of 1) net electrical charge dissipations in both particle and cell, 2) thermal disordering of dipole polarization in the module glass dielectrics, and 3) charge redistribution by the electrostatic interaction of particle and module glass. This long-lasting Fes for hours can significantly affect the solar panel soiling after sunset, especially combined with water condensation.

14 SOLAR ENERGY↗
DOE OSTI2020

Improved Stability and Cyclability of Ceramic Solid Electrolyte by Coating Polymer

Rechargeable all-solid-state lithium (Li) metal batteries show better safety and energy density compared to commercial Li-ion batteries using liquid electrolyte. As the key component of Li metal batteries, ceramic solid-state electrolyte has attracted great interest because of its high ion conductivity and great potential in interfacing with Li metal. Ceramic electrolyte has a more stable interface with Li metal than liquid electrolyte, but chemical reaction and Li dendrite growth at the electrolyte/Li interface are still significant, which causes device degradation and failure by cycling of Li plating and stripping. Unlike ceramic electrolyte, polymer electrolyte has a relatively stable interface with Li metal and better mechanical flexibility. Therefore, we introduced a polymer electrolyte coating to protect the ceramic electrolyte from direct contact with Li metal. The galvanotactic cycling Li plating/striping data on the devices with (without) the coating illustrates increased (decreased) overall conductivity and cyclability of the test cell by the cycling. Nanometer-scale ionic-transport imaging, based on atomic force microscopy, shows that cycling degrades the ceramic-only electrolyte by partially blocking ionic transport in areas; in contrast, cycling on the polymer-coated electrolyte improves ionic conductivity. Compared with the ceramic-only electrolyte, this novel polymer electrolyte coating on ceramic electrolyte shows less degradation when in contact with Li metal.

25 ENERGY STORAGE↗