Engineering topics
Xiao, Hai
Publications and source records attributed to Xiao, Hai.
Damage detection in a laboratory-scale wellbore applying Time Reversal and Nonlinear Elastic Wave Spectroscopy (TR NEWS)
We report Time Reversal and Nonlinear Elastic Wave Spectroscopy (TR-NEWS) has been used to focus acoustic energy, and make measurements correlated with damage in a variety of industrial materials. Most studies using TR-NEWS have focused on relatively small objects and may have multiple acoustic sources. In Earth, within energy extraction and carbon sequestration settings, the structure and scale of wellbores makes acoustic focusing challenging, as has been demonstrated through numerical simulations. This paper explores the feasibility of applying TR NEWS for damage detection in wellbores by constructing a laboratory-scale wellbore, and using TR to focus and make dynamic linear and nonlinear elastic measurements on it. During successive cycles of localized mechanical damage induced in the sample, the hysteretic nonlinear elastic parameter α increased with progressive mechanical damage. In addition to these strain-dependent changes in α, the width and peak amplitude of the time reversal focused energy changed near the damage site.
Distributed Acoustic Sensing Based on Coherent Microwave Photonics Interferometry
A microwave photonics method has been developed for measuring distributed acoustic signals. This method uses microwave-modulated low coherence light as a probe to interrogate distributed in-fiber interferometers, which are used to measure acoustic-induced strain. By sweeping the microwave frequency at a constant rate, the acoustic signals are encoded into the complex microwave spectrum. The microwave spectrum is transformed into the joint time–frequency domain and further processed to obtain the distributed acoustic signals. The method is first evaluated using an intrinsic Fabry Perot interferometer (IFPI). Acoustic signals of frequency up to 15.6 kHz were detected. The method was further demonstrated using an array of in-fiber weak reflectors and an external Michelson interferometer. Two piezoceramic cylinders (PCCs) driven at frequencies of 1700 Hz and 3430 Hz were used as acoustic sources. The experiment results show that the sensing system can locate multiple acoustic sources. The system resolves 20 nε when the spatial resolution is 5 cm. The recovered acoustic signals match the excitation signals in frequency, amplitude, and phase, indicating an excellent potential for distributed acoustic sensing (DAS).
Ultra-Fast Laser Fabrication of Alumina Micro-Sample Array and High-Throughput Characterization of Microstructure and Hardness
In the light of recent advances in material informatics, there is a great demand for high-throughput approaches of sample fabrication and property characterization. Currently, no high-throughput approach has been demonstrated for the fast sampling of the microstructure and the correlated properties. In this paper, we demonstrate the ultra-fast fabrication of an alumina sample array and the high-throughput hardness characterization of these sample units. The alumina sample array was fabricated using picosecond (PS) laser micromachining and CO2 laser sintering within a short time (i.e., less than a few minutes). After laser sintering, the hardness of these sample units was characterized using micro-indentation, and the microstructure was observed using scanning electron microscopy (SEM). In each sample unit, the microstructure was uniform for the entire top surface and within about 20 µm depth from the top surface. The relative density (RD) and corresponding micro-hardness of the sample units was found to continuously vary over a wide range from 89% RD with 600 kgf/mm2 hardness to 99% RD with 1609 kgf/mm2 hardness. For these laser-sintered samples, the correlation of hardness and relative density of the alumina matched well with the literature reports on sintered alumina obtained using conventional low-throughput furnace sintering experiments.
Chemically Inert Hydrocarbon-Based Slurries for Rapid Laser Sintering of Thin Proton-Conducting Ceramics
The process of rapid laser sintering of thin BaZrO 3 –BaCeO 3 -based proton-conducting electrolytes is being developed for easy fabrication of ceramic fuel cells and electrolyzers. However, cracks on the electrolytes caused by volume change due to chemical reactions between the basic ceramic constituents and the polar solvents during wet processing has been problematic. In order to address this issue, the use of chemically inert saturated-hydrocarbon-based slurries comprised of hexadecane, polybutene, and a long-chain saturated fatty acid were investigated in this work. By optimizing slurry composition and laser sintering conditions, a 20 mm long, 4 mm wide, 13.5-μm-thick and 97%-dense BaCe 0.7 Zr 0.1 Y 0.07 Sm 0.13 O 3-d membrane showing proton conductivity on the order of 10 –4 S•cm –1 at 600 °C was successfully prepared in just three seconds by laser sintering. As a result, the use of saturated-hydrocarbon-based slurries will facilitate wet processing and rapid laser sintering of proton-conducting ceramic electrolytes.
Machine learning-based microstructure prediction during laser sintering of alumina
Abstract Predicting material’s microstructure under new processing conditions is essential in advanced manufacturing and materials science. This is because the material’s microstructure hugely influences the material’s properties. We demonstrate an elegant machine learning algorithm that faithfully predicts the microstructure under new conditions, without the need of knowing the governing laws. We name this algorithm, RCWGAN-GP, which is regression-based conditional generative adversarial networks with Wasserstein loss function and gradient penalty. This algorithm was trained with experimental SEM micrographs from laser-sintered alumina under various laser powers. The RCWGAN-GP realistically regenerates the SEM micrographs under the trained laser powers. Impressively, it also faithfully predicts the alumina’s microstructure under unexplored laser powers. The predicted microstructure features, including the morphology of the sintered particles and the pores, match the experimental SEM micrographs very well. We further quantitatively examined the prediction accuracy of the RCWGAN-GP. We trained the algorithm with computer-created micrograph datasets of secondary-phase growth governed by the well-known Johnson–Mehl–Avrami (JMA) equation. The RCWGAN-GP accurately regenerates the micrographs at the trained time series, in terms of the grains’ shapes, sizes, and spatial distributions. More importantly, the predicted secondary phase fraction accurately follows the JMA curve.
All-Digital Plug and Play Passive RFID Sensors for Energy Efficient Building Control
This is the final report for the project “All-Digital Plug and Play Passive RFID Sensors for Energy Efficient Building Control”, funded by DOE, and performed by Clemson University, Phase IV Engineering and Harvard University from October 1, 2016 to December 31, 2020. The main objective of this project is to develop, demonstrate and pre-commercialize a novel, plug & play, battery-free, wireless sensor technology to enable low-cost (<$10 per node) indoor and outdoor temperature and humidity measurement for energy efficient building controls and operations. The proposed technology is based on the novel concept of all-digital sensing and its seamless integration with the passive RFID technology. This project focuses on the design, fabrication, material optimization, interrogation electronics, validation, and demonstration of the novel sensor nodes for building applications. The specific objectives of this research program include: (1) Design, fabricate and optimize a compact, robust, and high-resolution digitizer, which could convert rotation angle into digital numbers. (2) Develop the multi-physics-based modeling and simulation of the temperature/humidity transducer to derive a rational design of the architecture, dimension, structure, materials (i.e., mechanical, electrical, thermal and hygroscopic) properties and functions of the sensor node. (3) Design, fabricate and optimize the bi-material based humidity sensitive coil which could linearly transduce the environmental relative humidity variations to rotation angles. (4) Design, fabricate and optimize an UHF RFID platform which could support long-range passive wireless communications of 8-bit digital numbers. (5) Design, fabricate and optimize the miniaturized all-digital sensor using MEMS technology. (6) Validate the integrated all-digital sensing system in a real building environment to test the system’s performance.
Microwave–photonic low-coherence interferometry for dark zone free distributed optical fiber sensing
A microwave–photonic low-coherence interferometry (MPLCI) system is proposed for fully distributed optical fiber sensing. Assisted by an unbalanced Michelson interferometer, a low-coherence laser source is used to interrogate cascaded Fabry–Perot interferometers along with an optical fiber for a dark zone free (or spatially continuous) distributed measurement. Here, by combining the advantages of microwaves and photonics, the MPLCI system can synergistically achieve high sensitivity and high spatial resolution. Our tests have confirmed a strain resolution of 95 nε at the spatial resolution of 10 cm.
Ultra–fast, selective, non–melting, laser sintering of alumina with anisotropic and size–suppressed grains
In this paper, we report an ultra-fast sintering phenomenon of alumina achieved by the scanning laser irradiation method. Using CO 2 laser irradiation, we found that micrometer-sized alumina powder (d 50 = 1.2 µm) can be sintered close to full density within a few tens of seconds. The microstructure of laser-sintered alumina was different from that of the furnace-sintered alumina. The relative density and grain size of the laser-sintered alumina gradually decreased from the center of the laser beam to the edge. Anisotropy of the grain size was measured along and perpendicular to the scanning direction. This anisotropy decreased as the scanning speed decreased from 0.1 mm/s to 0.01 mm/s. The sintering master curve of grain size versus relative density, which reflects the sintering mechanism, was found to be affected by the laser scanning speed. When the laser scanning speed was 0.1 mm/s, grain size suppression was found for the almost fully dense alumina. However, at lower scanning speed (e.g., 0.01 mm/s), there was significant grain growth in the regions where the relative density was greater than 90%. Furthermore, these results clearly indicate that alumina can be sintered, in the solid-state, to a high density in a short time using scanning laser and the microstructure is different from the furnace-sintered alumina.
Advanced Manufacturing of Intermediate-Temperature Protonic Ceramic Electrochemical Cells
Proton conducting oxide (i.e., protonic ceramic) has been thought of as an ideal solid electrolyte for energy conversion and storage applications since Iwahara et al. reported the perovskite-type protonic ceramics represented by doped barium/strontium cerates and zirconates in the 1980s. Here, proton, as the charge carrier in protonic ceramics, possesses a much lower transport activation energy than oxide-ion, which has rendered protonic ceramics for extensive intermediate-temperature (IT, 400-700°C) electrochemical devices such as protonic ceramic fuel cells (PCFCs), reversible protonic ceramic fuel cells, and protonic ceramic membrane reactors.
Identification of the Electronic and Structural Dynamics of Catalytic Centers in Single-Fe-Atom Material
The lack of model single-atom catalysts (SACs) and atomic-resolution operando spectroscopic techniques greatly limits our comprehension of the nature of catalysis. Herein, based on the designed model single-Fe-atom catalysts with well-controlled microenvironments, we have explored the exact structure of catalytic centers and provided insights into a spin-crossover-involved mechanism for oxygen reduction reaction (ORR) using operando Raman, X-ray absorption spectroscopies, and the developed operando 57 Fe Mössbauer spectroscopy. In combination with theoretical studies, the N-FeN 4 C 10 moiety is evidenced as a more active site for ORR. Moreover, the potential-relevant dynamic cycles of both geometric structure and electronic configuration of reactive single-Fe-atom moieties are evidenced via capturing the peroxido (*O 2 -) and hydroxyl (*OH-) intermediates under in situ ORR conditions. Overall, we anticipate that the integration of operando techniques and SACs in this work shall shed some light on the electronic-level insight into the catalytic centers and underlying reaction mechanism.
Passive Digital Sensing Method and Its Implementation on Passive RFID Temperature Sensors
Benefitting from the advancement of digital electronics in the 20 th century, sensors have also gradually evolved from analog to digital. As semiconductor components are required in digital sensors, a power supply is still needed for the sensor. To eliminate the need for a power supply a concept of passive digital sensing is proposed. Different from the semiconductor-based electrical digital sensing method, the parameter to be measured is first converted to a mechanical signal, then the mechanical signal is encoded to multiple digital bits by a passive digitizer, where each bit is identified as open or short state that is detectable by general IO ports. To demonstrate the proposed sensing concept, a passive RFID temperature sensor is implemented using a bimetallic coil as the temperature sensing unit. The 6-bit binary codes are acquired and transmitted by a passive RFID that is powered by an energy harvester. Furthermore, the test results show that the temperature sensor has a measurement sensitivity of 1.32 °C/bit and a working distance over 10 meters.
ROBUST IN SITU STRAIN MEASUREMENTS TO MONITOR CO2 STORAGE
Presentation at annual project review meeting
Rapid Laser Processing of Thin Sr-Doped LaCrO 3– δ Interconnects for Solid Oxide Fuel Cells
Not provided.
Rapid laser reactive sintering of BaCe0.7Zr0.1Y0.1Yb0.1O3-δ electrolyte for protonic ceramic fuel cells
Not Available
One–Step Fabrication of Nanocrystalline Nanonetwork SnO 2 Gas Sensors by Integrated Multilaser Processing
An integrated multilaser process is developed to fabricate nanocrystalline nanonetwork SnO 2 gas sensors in one integrated procedure, which combines electrodes fabrication, nanomaterials deposition, and postannealing. Interdigit electrodes are fabricated on an Au-coated fused silica substrate using a picosecond (ps) laser, which ablates the Au coating from the back of the substrate to pattern the electrodes. A novel transmitted Ps laser deposition (TPLD) process is designed to deposit SnO 2 nanonetwork on the interdigit electrodes with precise deposition area control under a close target-to-substrate distance. The obtained SnO 2 nanonetwork is in situ postannealed by a CO 2 laser to improve the crystallinity, while the nano morphology and grain size keep intact. To investigate the morphology and formation process of the nanonetwork, the microstructure of the laser-deposited SnO 2 layer is characterized. As a result, the crystallization control of CO 2 laser annealing is investigated through analyzing the Raman spectrum, X-ray diffraction (XRD) patterns, and lattice structures of the samples. By exposed to H 2 atmosphere, the fabricated gas sensor is demonstrated for H 2 monitoring.
A metal-ceramic coaxial cable with multipoint Fabry-Pérot interferometers for monitoring distributed high temperature
A metal ceramic coaxial cable (MCCC) sensor containing multiple Fabry-Pérot interferometers (FPIs) has been designed, fabricated, and evaluated for measuring distributed high temperatures. The MCCC sensor demonstrated here consists of stainless steel tube and wire conductors, alumina tube insulator, and three pairs of air gap reflectors distributed along the cable. The multipoint sensor operation is realized by the joint time-frequency domain technique, which combines the functions of time-domain reflectometry and frequency division multiplexing to enable the measurement of spatially distributed temperature. The 3-point MCCC-FPI sensor has been demonstrated for distributed temperature measurements between 250 and 550 °C and operability up to 1000 °C. The sensor offers high sensitivity of >0.18 MHz/°C with a measurement resolution of 1 Hz and reasonably small high temperature measurement error range of ±3 °C.
Rapid Laser Reactive Sintering for Sustainable and Clean Preparation of Protonic Ceramics
Not Available