Engineering topics

Xiong, Juntao

Publications and source records attributed to Xiong, Juntao.

8 records

NASA NTRS2020

Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a jig twist optimization study of Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. A design flight condition corresponding to Mach 0.745 at 42000 ft is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. After the design is implemented, the drag coefficient of the twist optimized TTBW aircraft is reduced about 8 counts. At the end, a high-fidelity CFD solver FUN3D is used to validate the design.

BEAM3D↗

NASA NTRS2020

Simulation and Modeling of Flow Generated by Gust Generator in a Wind Tunnel

A computational study of a gust field generated by a gust generator in a low-speed wind tunnel. The gust generator is designed for the University of Washington Aeronautical Laboratory (UWAL) Kirsten wind tunnel for a gust load alleviation (GLA) control experiment of a Common Research Model (CRM) flexible wing utilizing the Variable Camber Continuous Trailing Edge Flap (VCCTEF). The gust generator comprises four horizontal NACA 0015 gust generator vanes placed upstream of the test section. Computational fluid dynamics simulations using a two-dimensional (2D) Unsteady-Reynolds-Averaged-Navier-Stokes (URANS) with k-ω Shear Stress Transport (SST) turbulence model provide detailed time-resolved information about the generated flow by the gust generator under prescribed sinusoidal motion. The characteristics of the induced flow by the gust generator are analyzed. A gust propagation model of the gust field is investigated. An unsteady lift model is developed using a varying-fidelity approach which includes a 2D interference aerodynamic model of the combined gust generator-wing system. The computed integrated unsteady lift is compared to experimental data for validation of the unsteady lift model. Both the amplitude and transport delay are found to be accurately captured by the unsteady lift model.

Nhan, Nguyen↗

NASA NTRS2020

Progress on Gust Load Alleviation Wind Tunnel Experiment and Aeroservoelastic Model Validation for a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper discusses a wind tunnel experiment of active gust load alleviation of a flexible wing which took place at University of Washington (UW) in 2019. The experiment performed under a NASA SBIR contract with Scientific Systems Company, Inc (SSCI). The objective of the experiment is to demonstrate active controls of the Variable Camber Continuous Trailing Edge Flap (VCCTEF) system for gust load alleviation and real-time drag optimization. The wind tunnel model is a 8.2% sub-scale Common Research Model (CRM) wing. The wing structure is designed to provide a substantial degree of flexibility to represent that of a modern high-aspect ratio wing. Eight active control surfaces are employed in the VCCTEF. A new gust generator system was designed and installed by UW under a sub-contract with SSCI. The first test entry started in July 2019 and ended in September 2019. During this test entry, many significant issues were found with the hardware and software. The significant issues with the servos prevented the test objective from being completed. A follow-up second test entry in 2020 is being planned. The wing system is being repaired by SSCI. This paper reports on the progress of this experimental effort and the aeroservoelastic (ASE) model validation which was conducted during the test entry.

Nguyen, Nhan↗

NASA NTRS2020

Jig Twist Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft and High-Fidelity CFD Validation

This paper presents a jig twist optimization study of Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft using an in-house developed aero-structural analysis solver VSPAERO coupled to BEAM3D. A vortex-lattice model of the TTBW model is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO model to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which causes a deflection-dependent nonlinear stiffness. The VSPAERO model is coupled to the corresponding finite-element model to provide a rapid aero-structural analysis. A flight condition corresponding to Mach 0.745 at 42000 ft is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. After the design is implemented, the drag coefficient of the twist optimized TTBW aircraft is reduced about 8 counts. At the end, a high-fidelity CFD solver FUN3D is used to validate the design.

Xiong, Juntao↗

NASA NTRS2020

Multi-Objective Gust Load Alleviation Control Designs for an Aeroelastic Wind Tunnel Demonstration Wing

This paper presents several control and gust disturbance estimation techniques applied to a mathematical model of a physical flexible wing wind tunnel model used in ongoing tests at the University of Washington Aeronautical Laboratory's Kirsten Wind Tunnel. Three methods of gust disturbance estimation are presented, followed by three control methods: LQG, Basic Multi-Objective (BMO), and a novel Multi-Objective Prediction Correction (MOPC) controller. The latter of which augments a multi-objective controller, and attempts to correct for errors in the disturbance estimate. A simplified linear simulation of the three controllers is performed and a simple MIMO stability and robustness assessment is performed. Then, the same controllers are simulated in a higher fidelity Simulink environment that captures sampling, saturation and noise effects. This preliminary analysis indicates that the BMO controller provides the best performance and largest stability margins.

Drew, Michael C.↗

NASA NTRS2020

Acoustic Optimization for Anti-Phase Asymmetric Rotor

This investigation seeks to optimize the implementation of anti-phase alternating trailing edge (TE) patterns for rotor noise suppression. The design objective is to maximize reduction of noise perceived by the community while maintaining the aerodynamic thrust. Computations using a three-dimensional Unsteady-Reynolds-Averaged-Navier-Stokes (URANS) with k-w Shear Stress Transport (SST) turbulence model and Ffowcs-Williams and Hawkings (FW-H) formula are used to obtain aerodynamic thrust and far-field noise level. A parametric acoustic study of 13 configurations of KDE rotor with variable alternating trailing edge period, alternating trailing edge length, and trailing edge deflection angle is conducted. The best design candidate for the KDE rotor has a four-period TE waveform which results in a reduction in far-field noise level of 2.1 dB in the hover condition and a reduction of 1.1 dB in the forward flight condition at 9.7 m/s. A further parametric acoustic study is conducted for a different rotor manufactured by APC. Six APC rotor design candidates are simulated. The best design candidate 4H for the APC rotor results in a reduction in far-field noise level of 4.0 dB in the hover condition and a reduction of 1.3 dB in the forward flight condition at 9.7 m/s. A series of acoustic experiments in the Penn State University (PSU) anechoic chamber have been conducted. In the forward flight condition at 9.7 m/s, the APC anti-phase 4H rotor offers clear evidence of noise suppression capability across a wide range of the azimuthal angle. In the broadband frequency range of 2000-4000 Hz, the APC anti-phase 4H rotor produces as much as 6 dB noise reduction. The experimental results appear to confirm the noise suppression capability of the proposed anti-phase rotor design concepts.

Xiong, Juntao↗

NASA NTRS2019

Aero-Structural Modeling of the Truss-Braced Wing Aircraft Using Potential Method with Correction Methods for Transonic Viscous Flow and Wing-Strut Interference Aerodynamics

This paper describes an aero-structural modeling method for the Transonic Truss-Braced Wing (TTBW) aircraft using VSPAERO. A vortex-lattice model of the TTBW aircraft is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO models to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which cause a deflection dependent nonlinear stiffness. The VSPAERO models are coupled to the finite-element model to provide a rapid capability for aero-structural modeling and flutter analysis. A flight-optimized jig twist model is being developed and will be applied for the purpose of generating a full flight dynamic model of the TTBW aircraft.

Fugate, Jason↗

NASA NTRS2019

Investigation of Transonic Truss-Braced Wing Aircraft Transonic Wing-Strut Interference Effects Using FUN3D

This paper presents a computational study of transonic wing-strut interference effects of Transonic Truss-Braced Wing (TTBW) aircraft using the high-fidelity CFD (Computational Fluid Dynamics) code FUN3D (Fully Unstructured Navier-Stokes Three Dimensional). The study is conducted for the wing-strut and the wing-alone configurations at different Mach numbers and Reynolds numbers. The interference effects are calculated by comparing the wing aerodynamics along the spanwise direction between the wing-strut and the wing-alone configurations. The presence of the strut underneath the wing induces a suction peak on the lower surface of the wing, which causes changes in aerodynamic forces and moments, as well as the aerodynamic center location. The interference effects become more pronounced as the Mach number increases. The Reynolds number has less impact on the interference effects. A transonic wing-strut interference aerodynamic correction method is developed for use in a lower-fidelity tool, VSPAERO [a vortex lattice flow solver], coupled to a finite-element model for rapid flutter analysis.

Xiong, Juntao↗