Engineering topics

Xu, Ben

Publications and source records attributed to Xu, Ben.

9 records

DOE OSTI2024

A Techno-Economic Analysis of a 50MWth Light-Trapping Cavity-Planar Solar Receiver Tower Capital Expenditures and its Cost Mitigation Strategies

To maximize thermal efficiency, the National Renewable Energy Laboratory (NREL) has proposed a light-trapping cavity-planar receiver design intended to capture energy from reradiating surfaces. This system implements a macroscale light trapping mechanism induced by panels with triangular channels, this mechanism allows for elevated temperatures on the receiver panels and in turn the temperature of the HTF; using this design coupled with the implementation of a fluidized particle flow as the HTF, it can be expected for some components to reach a peak working temperature of nearly 1000 degrees C cyclically throughout each day-night cycle. While these temperatures correlate to higher efficiency of the CSP tower they also demand intense thermomechanical properties from the materials used to make the receiver panels. In this analysis, we will list our assumptions to provide clarity on the significance of our calculation. This cost analysis will be conducted using a combination of both case study data and surveying industry to determine costs that are relevant to the current market trends. This analysis represents an early attempt to establish the Capital Expenditures required for a CSP tower of such design to determine the feasibility of implementing such a system in the industry.

concentrated solar power (CSP)↗

DOE OSTI2024

Flow and Heat Transfer Experimental Study for 3D-Printed Solar Receiving Tubes With Helical Fins at Internal Surface

3D-printing technology was applied to fabricate novel solar thermal collection tubes that have internal heat transfer enhancement fins and external surfaces with high solar absorptivity and low emissivity due to the ability to use different materials in one tube. Helical fins were selected to introduce circumferential flow and thus minimize the circumferential temperature difference of the tube that receives sunlight on one side. The structures of the helical fins were previously optimized from computational fluid dynamics (CFD) analysis with the objective of low entropy production rate by looking for high heat transfer coefficient and relatively lower pressure loss. High-temperature alloy, Inconel-718, was used to 3D print the tubes, which can resist corrosion for the potential application of molten chloride salts as heat transfer fluid. Experimental tests were carried out using water as the heat transfer fluid with the high heat flux provided by a tubular furnace heater. The tested Reynolds number ranges from 3.9 × 10 3 to 6.1 × 10 4 . Heat transfer coefficients of up to 2.8 times that of the smooth tube could be obtained with the expense of increased pressure loss compared to that of the smooth tube. The total system entropy generation can be significantly reduced due to the benefit of heat transfer enhancement that is greater than the expenses of the increased pressure loss. The experimental results of the 3D-printed heat transfer tubes confirmed the CFD-based results of fin optimization. Furthermore, the novel heat transfer tube is recommended for application in concentrating solar power systems.

14 SOLAR ENERGY↗

DOE OSTI2024

3D Printing of Inconel 718 with Enhanced Boron Composition as a Novel Solar Absorber Tube Material in the Concentrated Solar Power (CSP) System

The growing demands for elevated efficiency in the solar energy industry led researchers to focus on the development of functional solar absorber tube material in concentrated solar power (CSP) systems, when molten salts are adopted as the heat transfer fluid. In this study, the typical solar absorber tube material, Inconel 718, was enhanced with boron to achieve a higher solar absorptivity in the visible light spectrum. Combined with an additive manufacturing (AM) method, the boron composition exceeded the traditional manufacturing limit of 60 ppm without microstructural defects. The boron-enhanced Inconel 718 exhibited a high solar absorptivity of nearly 90 % while maintaining a high thermal cycle fatigue resistance after thermal cycling treatment between 550°C and 720°C. The boron composition was increased to the manufacturing failure point, and the effects of different boron compositions on mechanical properties, microstructure, and optical properties were studied. The provided microstructure-property map in this study delivers high potentials of functional AM-printed alloy material in CSP applications.

13 HYDRO ENERGY↗

DOE OSTI2023

Helical Fins for Concentrated Solar Receivers: Design Optimization and Entropy Analysis

Concentrated solar power (CSP) with thermal energy storage (TES) has the potential to achieve grid parity. This can be realized by operating CSP systems at temperatures above 700 °C with high-efficiency sCO 2 power cycles. However, operating CSP systems at such temperatures poses several challenges, among which the design of solar receivers to accommodate increased thermal loads is critical. To this end, this work explores and optimizes various swirl-inducing internal fin designs for solar receiver tubes. These fin designs not only improve the thermal performance of receiver tubes but also levelize temperature unevenness caused by non-uniform thermal loading. In this work, the geometric parameters of the fin designs are optimized to maximize the Nusselt number with a constraint on the friction factor. This optimization, however, is computationally intensive, requiring hundreds of simulation calls to computational fluid dynamics (CFD) models. Here, to circumvent this problem, surrogate models are used to approximate the simulation outputs needed during the optimization. In addition, this study also examines the fin designs from an entropy generation perspective. To this end, the entropy contributions from thermal and viscous effects are quantitatively compared while varying the operational Reynolds number.

14 SOLAR ENERGY↗

DOE OSTI2023

Numerical Study of Solar Receiver Tube With Modified Surface Roughness for Enhanced and Selective Absorptivity in Concentrated Solar Power Tower

Abstract Concentrated solar power (CSP) is a reliable renewable energy source that is progressively lowering its cost of energy. However, the heat loss due to reflected and emitted radiation hinders the maximum achievable thermal efficiency for solar receiver tubes on the solar tower. Current solar selective coatings cannot withstand the high temperatures that come with state-of-the-art CSP towers often needing to be recoated soon after initial operation. We intend to use Inconel 718 with different additive manufacturing (AM) practices to construct surfaces that allow for more light-trapping to occur. By adjusting printing parameters, we can tailor a surface to allow for more absorption while diminishing emitted radiation heat loss. By using COMSOL Multiphysics, we can generate these theoretical surfaces to emulate a printed surface, and using the coupled Multiphysics we can simulate how the surface dictates radiation properties. Our results show that by having a rougher surface we can enhance the absorptivity of Inconel 718 (IN718) by 38.8%. We expect this work to transform how solar absorber tubes are manufactured without using selective coatings and supplement the US Department of Energy (DOE) 2030 SunShot Initiative.

14 SOLAR ENERGY↗

DOE OSTI2023

3D Printing of Solar Absorber Tube with Internal/External Structures for Heat Transfer Enhancement and Temperature Leveling using Additive Manufacturing Technology

In this project, to tackle the technical obstacles, we utilized Laser Additive Alloying (LAA), an additive manufacturing (AM) technology, to 3D print the entire absorber tube with optimized helical fins to improve heat transfer at the expense of minimized pressure drop increase. The 3D printed absorber tubes can increase the uniformity of circumferential temperature distribution, reduced the thermal stresses, decrease the heat loss, and reach the target receiver thermal efficiency.

14 SOLAR ENERGY↗

DOE OSTI2022

Experimental Study of Eutectic Molten Salts NaCl/KCl/ZnCl2 Heat Transfer Inside a Smooth Tube for High-Temperature Application

Abstract Eutectic salts NaCl-KCl-ZnCl2 and NaCl-KCl-MgCl2 are two of the chloride salt systems that are promising for being used as high-temperature heat transfer fluid (HTF) and thermal energy storage (TES) materials in a wide range of temperatures from 230 °C to 750 °C in concentrated solar thermal power systems. To conduct measurement of the heat transfer coefficient of the molten salt at high temperatures, a circulation system and instrumentation of flow and heat transfer was constructed. Experimental measurement of the convective heat transfer coefficients of NaCl-KCl-ZnCl2 (molar fraction: 13.8–41.9–44.3%) inside tubes has been accomplished to find the most suitable heat transfer correlations. Experience of salt processing and operation of the high-temperature heat transfer test system was obtained. Two correlations, Dittus-Boelter equation and Gnielinski’s correlation for Nusselt number against Reynolds number and Prandtl number, are evaluated using the test results, and the latter correlation is recommended due to its better agreement of prediction against tested data.

Energy & Fuels↗

DOE OSTI2021

Toroidal polar topology in strained ferroelectric polymer

Polar topological texture has become an emerging research field for exotic phenomena and potential applications in reconfigurable electronic devices. Here, we report toroidal topological texture self-organized in a ferroelectric polymer, poly(vinylidene fluoride-ran-trifluoroethylene) [P(VDF-TrFE)], that exhibits concentric topology with anticoupled chiral domains. The interplay among the elastic, electric, and gradient energies results in continuous rotation and toroidal assembly of the polarization perpendicular to polymer chains, whereas relaxor behavior is induced along polymer chains. Such toroidal polar topology gives rise to periodic absorption of polarized far-infrared (FIR) waves, enabling the manipulation of the terahertz wave on a mesoscopic scale. Our observations should inform design principles for flexible ferroic materials toward complex topologies and provide opportunities for multistimuli conversions in flexible electronics.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Mechanisms of Skyrmion and Skyrmion Crystal Formation from the Conical Phase

Real-space topological magnetic structures such as skyrmions and merons are promising candidates for information storage and transport. However, the microscopic mechanisms that control their formation and evolution are still unclear. In this work, using in situ Lorentz transmission electron microscopy, we demonstrate that skyrmion crystals (SkXs) can nucleate, grow, and evolve from the conical phase in the same ways that real nanocrystals form from vapors or solutions. More intriguingly, individual skyrmions can also “reproduce” by division in a mitosis-like process that allows them to annihilate SkX lattice imperfections, which is not available to crystals made of mass-conserving particles. Combined string method and micromagnetic calculations show that competition between repulsive and attractive interactions between skyrmions governs particle-like SkX growth, but nonconservative SkX growth appears to be defect mediated. Our results provide insights toward manipulating magnetic topological states by applying established crystal growth theory, adapted to account for the new process of skyrmion mitosis.

36 MATERIALS SCIENCE↗