Search NASA⌕ Search

Engineering topics

Xu, Chi

Publications and source records attributed to Xu, Chi.

At least 19 records

Size-tunable silver nanoparticle synthesis in glycerol driven by a low-pressure nonthermal plasma

Silver nanoparticles (NPs) are extensively used in electronic components, chemical sensors, and disinfection applications, in which many of their properties depend on particle size. However, control over silver NP size and morphology still remains a challenge for many synthesis techniques. Here, in this work, we demonstrate the surfactant-free synthesis of silver NPs using a low-pressure inductively coupled nonthermal argon plasma. Continuously forming droplets of silver nitrate (AgNO 3 ) precursor dissolved in glycerol are exposed to the plasma, with the droplet residence time being determined by the precursor flow rate. Glycerol has rarely been studied in plasma-liquid interactions but shows favorable properties for controlled NP synthesis at low pressure. We show that the droplet residence time and plasma power have strong influence on NP properties, and that improved size control and particle monodispersity can be achieved by pulsed power operation. Silver NPs had mean diameters of 20 nm with geometric standard deviations of 1.6 under continuous wave operation, which decreased to 6 nm mean and 1.3 geometric standard deviation for pulsed power operation at 100 Hz and 20% duty cycle. We propose that solvated electrons from the plasma and vacuum ultraviolet (VUV) radiation induced electrons produced in glycerol are the main reducing agents of Ag + , the precursor for NPs, while no significant change of chemical composition of the glycerol solvent was detected.

36 MATERIALS SCIENCE↗

Inferring plant–plant interactions using remote sensing

Rapid technological advancements and increasing data availability have improved the capacity to monitor and evaluate Earth's ecology via remote sensing. However, remote sensing is notoriously ‘blind’ to fine-scale ecological processes such as interactions among plants, which encompass a central topic in ecology. Here, we discuss how remote sensing technologies can help infer plant–plant interactions and their roles in shaping plant-based systems at individual, community and landscape levels. At each of these levels, we outline the key attributes of ecosystems that emerge as a product of plant–plant interactions and could possibly be detected by remote sensing data. We review the theoretical bases, approaches and prospects of how inference of plant–plant interactions can be assessed remotely. At the individual level, we illustrate how close-range remote sensing tools can help to infer plant–plant interactions, especially in experimental settings. At the community level, we use forests to illustrate how remotely sensed community structure can be used to infer dominant interactions as a fundamental force in shaping plant communities. At the landscape level, we highlight how remotely sensed attributes of vegetation states and spatial vegetation patterns can be used to assess the role of local plant–plant interactions in shaping landscape ecological systems. Synthesis . Remote sensing extends the domain of plant ecology to broader and finer spatial scales, assisting to scale ecological patterns and search for generic rules. Robust remote sensing approaches are likely to extend our understanding of how plant–plant interactions shape ecological processes across scales—from individuals to landscapes. Combining these approaches with theories, models, experiments, data-driven approaches and data analysis algorithms will firmly embed remote sensing techniques into ecological context and open new pathways to better understand biotic interactions.

59 BASIC BIOLOGICAL SCIENCES↗

Plasma-driven solution electrolysis

Plasmas interacting with liquids enable the generation of a highly reactive interfacial liquid layer due to a variety of processes driven by plasma-produced electrons, ions, photons, and radicals. These processes show promise to enable selective, efficient, and green chemical transformations and new material synthesis approaches. While many differences are to be expected between conventional electrolysis and plasma–liquid interactions, plasma–liquid interactions can be viewed, to a first approximation, as replacing a metal electrode in an electrolytic cell with a gas phase plasma. For this reason, we refer to this method as plasma-driven solution electrochemistry (PDSE). In this Perspective, we address two fundamental questions that should be answered to enable researchers to make transformational advances in PDSE: How far from equilibrium can plasma-induced solution processes be driven? and What are the fundamental differences between PDSE and other more traditional electrochemical processes? Different aspects of both questions are discussed in five sub-questions for which we review the current state-of-the art and we provide a motivation and research vision.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-energy synchrotron x-ray study of deformation-induced martensitic transformation in a neutron-irradiated Type 316 stainless steel

An unusual tensile deformation behaviour in the form of a propagating band along the sample gauge was observed in two neutron-irradiated 316 stainless steel samples during room-temperature tests, leading to a combination of high strength and high ductility. These bands were not observed in an unirradiated counterpart. With the help of in situ high-energy synchrotron x-ray diffraction, the phase-specific crystal information was tracked at different deformation levels in each sample. Post-irradiation and post-deformation samples were examined using electron microscopy to characterize various microstructural features. All samples displayed a deformation-induced martensitic phase transformation, which was identified as a second strain-hardening mechanism accompanying the dislocation hardening. The deformation-induced martensitic transformation was rationalized by the effect of applied stress on the effective martensite start temperature. The results showed that the irradiation did not alter the dislocation hardening and the martensitic transformation mechanisms, but the increased yield strength in irradiated materials facilitated the localized phase transformation at the onset of plastic deformation, in contrast to the unirradiated material which required pre-straining. The hardening effect of the martensitic transformation reduced the tendency towards necking and mitigated the loss of ductility in the irradiated material by carrying the deformation in the form of a propagating band. Despite the beneficial effect from the martensitic transformation, this study indicates that this mechanism cannot not be activated at typical operating temperatures of nuclear reactors.

36 MATERIALS SCIENCE↗

Tellurene Photodetector with High Gain and Wide Bandwidth

Two-dimensional (2D) semiconductors have been extensively explored as a new class of materials with great potential. In particular, black phosphorus (BP) has been considered to be a strong candidate for applications such as high-performance infrared photodetectors. However, the scalability of BP thin film is still a challenge, and its poor stability in the air has hampered the progress of the commercialization of BP devices. Herein, we report the use of hydrothermal-synthesized and air-stable 2D tellurene nanoflakes for broadband and ultrasensitive photodetection. The tellurene nanoflakes show high hole mobilities up to 458 cm 2 /V·s at ambient conditions, and the tellurene photodetector presents peak extrinsic responsivity of 383 A/W, 19.2 mA/W, and 18.9 mA/W at 520 nm, 1.55 μm, and 3.39 μm light wavelength, respectively. Because of the photogating effect, high gains up to 1.9 × 10 3 and 3.15 × 10 4 are obtained at 520 nm and 3.39 μm wavelength, respectively. At the communication wavelength of 1.55 μm, the tellurene photodetector exhibits an exceptionally high anisotropic behavior, and a large bandwidth of 37 MHz is obtained. The photodetection performance at different wavelength is further supported by the corresponding quantum molecular dynamics (QMD) simulations. Our approach has demonstrated the air-stable tellurene photodetectors that fully cover the short-wave infrared band with ultrafast photoresponse.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transition from an Antiferromagnetic Ground State to Robust Ferrimagnetic Order with Curie Temperature above 420 K in Manganese-based Antiperovskite-type Structures

Manganese (Mn)-based antiperovskite structures (Mn 3 AX, where A and X represent the 3d transition-metal elements and N or C atoms, respectively) have attracted growing attention because of their novel electronic and magnetic properties. However, the lack of an effective approach to regulate the magnetic coupling in Mn(3)AX crystal structure, particularly in antiferromagnetic ground states, hinders their further design and applications. Herein, robust high-temperature ferrimagnetic order with a Curie temperature (T C ) in the range of approximate to 390-420 K was successfully achieved in Mn 3 GaxNx (x = 0.5, 0.6, and 0.7) via composition-deficient engineering. A systematic investigation, including synchrotron X-ray diffraction, neutron powder diffraction, pair distribution function, X-ray absorption near-edge structure, magnetic characterization, and first-principles calculations, convincingly indicated that the redistribution of partial atoms in the antiferromagnetic ground state was responsible for the observed long-range magnetic order. These results not only provide a new perspective into the design and construction of high-temperature ferrimagnets based on the Mn 3 AX structure, but also open up a promising avenue for the further design of Mn 3 AX-based spintronic or other multifunctional devices.

36 MATERIALS SCIENCE↗

Flux Pinning-Induced Stress in a Long Hollow Cylindrical Superconductor Restricted by a Metal Tube

The tensile stress in a hollow cylindrical superconductor completely restricted by a metal tube in a parallel magnetic field is investigated. Using the plane strain approach, analytical expressions for the stress distribution of the superconductor and the contact stress between the metal tube and the superconductor are obtained and show that both the ratio of Young’s modulus and thickness ratio of the high-temperature superconductors and the metal tube significantly affect the stress distribution in the superconductor explicitly. In addition, the flux pinning-induced stress in the above-mentioned superconductor is systematically studied by the exponential critical state model during the field cooling process. The results indicate that the metal tube can reduce effectively the tensile stress in the hollow cylindrical superconductor during the magnetization process. The findings suggest that the appropriate selection of material parameters and size of the metal tube can improve superconductor performance efficiently.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microstructural evolution of NF709 austenitic stainless steel under in-situ ion irradiations at room temperature, 300, 400, 500 and 600 °C

Irradiation induced microstructural changes in the NF709 austenitic stainless steel were investigated under 1 MeV Kr ion irradiations to a dose of 3 dpa at room temperature (RT), 300, 400, 500 and 600 °C, and a dose of 20 dpa at RT. The irradiation-induced defects and the stability of precipitates were characterized with transmission electron microscopy (TEM). Frank dislocation loops were observed in all the irradiated samples, and the loop sizes were much larger at 600 °C than those at lower temperatures. “Raft” defect structures, formed through self-alignment of small dislocation loops, were also observed in all irradiated samples. M23C6 precipitates were amorphorized under irradiations at RT and 300 °C, but remained to be crystalline at 400 °C and above. MX precipitates were stable under irradiations at RT up to 20 dpa, and at temperatures below 600 °C to 3 dpa. At 600 °C, some MX precipitates were observed to dissolve during in-situ irradiation, suggesting possible precipitate instability at this irradiation temperature.

36 MATERIALS SCIENCE↗

In-situ high-energy X-ray characterization of neutron irradiated HT-UPS stainless steel under tensile deformation

Here, the tensile deformation behavior of a high-temperature, ultrafine-precipitate strengthened (HT-UPS) stainless steel was characterized in-situ with high-energy X-ray diffraction at 20 and 400 °C. The HT-UPS samples were neutron irradiated to 3 dpa at 400 °C. Significant irradiation hardening and ductility loss were observed at both temperatures. Lattice strain evolutions of the irradiated samples showed a strong linear response up to near the onset of the macroscopic yield, in contrast to the unirradiated HT-UPS which showed a pronounced non-linear behavior well below the macroscopic yield. While the room temperature diffraction elastic moduli in the longitudinal direction increased after irradiation, the 400 degrees C moduli were similar before and after irradiation. The evolution of the {200} lattice strain parallel to the loading axis (ε L {200} ) showed unique characteristics: in the plastic regime, the evolution of (ε L {200} ) after yield is temperature-dependent in the unirradiated specimens but temperature-independent in the irradiated specimens; and the value of (ε L {200} ) at the yield is an irradiation-sensitive, temperature-independent . parameter. The evolution of (ε L {200} ) corresponds well with the dislocation density evolution, and is an effective probe of the deformation-induced long-range internal stresses in the HT-UPS steel.

36 MATERIALS SCIENCE↗

Effects of neutron irradiation and post-irradiation annealing on the microstructure of HT-UPS stainless steel

Microstructural changes resulted from neutron irradiation and post-irradiation annealing in a high-temperature ultra-fine precipitate strengthened (HT-UPS) stainless steel were characterized using transmission electron microscopy (TEM) and atom probe tomography (APT). Three HT-UPS samples were neutron-irradiated to 3 dpa at 500 °C, and after irradiation, two of them were annealed for 1 h at 600 °C and 700 °C, respectively. Frank dislocation loops were the dominant defect structure in both the as-irradiated and 600 °C post-irradiation-annealed (PIAed) samples, and the loop sizes and densities were similar in these two samples. Unfaulted dislocation loops were observed in the 700 °C PIAed sample, and the loop density was greatly reduced in comparison with that in the as-irradiated sample. Nano-sized MX precipitates were observed under TEM in the 700 °C PIAed sample, but not in the 600 °C PIAed or the as-irradiated samples. The titanium-rich clusters were identified in all three samples using APT. The post-irradiation annealing (PIA) caused the growth of the Ti-rich clusters with a stronger effect at 700 °C than at 600 °C. The irradiation caused elemental segregations at the grain boundary and the grain interior, and the grain boundary segregation behavior is consistent with observations in other irradiated austenitic steels. Here, APT results showed that PIA reduced the magnitude of irradiation induced segregations.

36 MATERIALS SCIENCE↗

Towards diluted magnetism in TaAs

Magnetism in Weyl semimetals is desired to investigate the interaction between the magnetic moments and Weyl fermions, e.g., to explore anomalous quantum Hall phenomena. In this work, we demonstrate that proton irradiation is an effective tool to induce ferromagnetism in the Weyl semimetal TaAs. The intrinsic magnetism is observed with a transition temperature above room temperature. The magnetic moments from d states are found to be localized around Ta atoms. Further, the first-principles calculations indicate that the d states localized on the nearest-neighbor Ta atoms of As vacancy sites are responsible for the observed magnetic moments and the long-ranged magnetic order. The results show the feasibility of inducing ferromagnetism in Weyl semimetals so that they may facilitate the applications of this material in spintronics.

36 MATERIALS SCIENCE↗

Microstructural Evolution of NF709 Steel under In-situ Ion Irradiations at Room Temperature to 600 deg. C

NF709 is one of the advanced austenitic stainless steels considered for the advanced reactor systems which are characterized by high temperature, intense radiation and potentially corrosive environments. NF709 is a nitrogen-stabilized and niobium-strengthened alloy, and it provides strength nearly double that for conventional 304 and 316 stainless steels at a temperature range of 600-750 deg. C. In addition, this alloy demonstrates excellent metallurgical stability and high-temperature creep resistance, which is critical for advanced fast-reactor structural materials. Nevertheless, there is very limited irradiation data on NF709 to date, and its radiation-resistance is to be proved. It this paper, we studied the radiation response of NF709 by using the in-situ ion irradiation at the Intermediate Voltage Electron Microscopy (IVEM)- Tandem Facility, located at Argonne National Lab (ANL) and the systematic post-irradiation characterizations using transmission electron microscopy (TEM) were conducted.

36 MATERIALS SCIENCE↗

i RadMat: A thermo-mechanical testing system for in situ high-energy X-ray characterization of radioactive specimens

Here, we present an in situ Rad iated Mat erials (iRadMat) experimental module designed to interface with a servo-hydraulic load frame for X-ray measurements at beamline 1-ID at the Advanced Photon Source. This new capability allows in situ studies of radioactive specimens subject to thermo-mechanical loading using a suite of high-energy X-ray scattering and imaging techniques. The iRadMat is a radiation-shielded vacuum heating system with the sample rotation-under-load capability. We describe the design features and performances of the iRadMat and present a dataset from a 300 °C uniaxial tensile test of a neutron-irradiated pure Fe specimen to demonstrate its capabilities.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

In situ high-energy X-ray diffraction study of tensile deformation of neutron-irradiated polycrystalline Fe-9%Cr alloy

The effect of neutron irradiation on tensile deformation of a Fe-9wt.%Cr alloy was investigated using in situ high-energy synchrotron X-ray diffraction during room-temperature uniaxial tensile tests. New insights into the deformation mechanisms were obtained through the measurements of lattice strain evolution and the analysis of diffraction peak broadening using the modified Williamson-Hall method. Two neutron-irradiated specimens, one irradiated at 300 °C to 0.01 dpa and the other at 450 °C to 0.01dpa, were tested along with an unirradiated specimen. The macroscopic stress–strain curves of the irradiated specimens showed increased strength, reduced ductility and work-hardening exponent compared to the unirradiated specimen. The evolutions of the lattice strain, the dislocation density and the coherent scattering domain size in the deformation process revealed different roles of the submicroscopic defects in the 300°C/0.01 dpa specimen and the TEM-visible nanometer-sized dislocation loops in the 450°C/0.01 dpa specimen: submicroscopic defects extended the linear work hardening stage (stage II) to a higher strain, while irradiation-induced dislocation loops were more effective in dislocation pinning. Lastly, while the work hardening rate of stage II was unaffected by irradiation, significant dynamic recovery in stage III in the irradiated specimens led to the early onset of necking without stage IV as observed in the unirradiated specimen.

36 MATERIALS SCIENCE↗

3D Study of Neutron Irradiation Effects on Tensile Deformation in Fe-based Alloys using High Energy Synchrotron X-rays

Recent development of 3D synchrotron X-ray techniques offers new opportunities for the investigation of nuclear materials. In this study, we use the high energy Xray diffraction microscopy (HEDM), also known as 3DXRD, to investigate the effects of neutron irradiation on microstructural response during tensile deformation in a Fe- 9%Cr alloy. Fe-9Cr has been studied extensively in experiments and modelling as a ferritic model alloy for its response to neutron irradiation. It is found that irradiation-induced hardening and reduction of ductility are significant even at very low doses, and the primary deformation mechanism is channeling. Different from earlier studies, here we focus on grain-level responses to deformation and aim to elucidate the effect of irradiation by employing the far-field HEDM setup (FF-HEDM) to obtain strains, crystallographic orientations, and centers of masses of hundreds of grains in undeformed and deformed states, providing rich 3D information well beyond the TEM and traditional diffraction measurements. It offers a deeper understanding of the structure-property relationship in nuclear materials. (authors)

36 MATERIALS SCIENCE↗

In-Situ High Energy X-ray Characterization of Tensile Deformation of Advanced Austenitic Stainless Steels

A deep understanding of the deformation mechanisms for next-generation structural materials of advanced nuclear reactors is critical to their successful applications. For this purpose, high energy synchrotron X-ray characterization techniques in combination with in situ thermo-mechanical loading have distinctive advantages in correlating the mechanical responses of the specimens with their microstructure evolution in real time. In this study, this method is employed to compare the deformation characteristics of two advanced austenitic stainless steels, NF709 steel a High-Temperature Ultrafine-Precipitate Strengthened (HT-UPS) steel, with a traditional 316 austenitic stainless steel (SS). The NF709 and HT-UPS steels are both promising candidates for next generation nuclear energy systems. The NF709 is a 20Cr-25Ni austenitic stainless steel stabilized with Nb/Ti(C,N) precipitates and possesses excellent high temperature and corrosion resistance. The HT-UPS steel (Fe-14Cr-16Ni-Ti,Nb,V) also has much improved creep resistance and high temperature performance than 316SS through the careful control of minor alloying elements to form creep resistant precipitates. While both have shown improved mechanical properties over 316SS, their deformation characteristics and underlying mechanisms are yet to be fully explored. The recent applications of simultaneous Wide-Angle X-ray Scattering (WAXS) and Small-Angle X-ray Scattering (SAXS) techniques under thermo-mechanical loading of steel samples have revealed valuable insights of the microstructural evolution during deformation. This work is to apply these techniques to characterize the deformation behaviors and also understand their relationship with the microstructures of advanced austenitic stainless steels. (authors)

36 MATERIALS SCIENCE↗