Engineering topics
Xu, G. S.
Publications and source records attributed to Xu, G. S..
Turbulence spreading effects on the ELM size and SOL width
BOUT++ turbulence simulations were performed to investigate the impact of turbulence spreading on the edge localized mode (ELM) size and divertor heat flux width (λ q ) broadening in small ELM regimes. Here, this study is motivated by EAST experiments. BOUT++ linear simulations of a pedestal radial electric field (E r ) scan show that the dominant toroidal number mode (n) shifts from high-n to low-n, with a narrow mode spectrum, and the maximum linear growth rate increases as the pedestal E r well deepens. The nonlinear simulations show that as the net E × B pedestal flow increases, the pressure fluctuation level and its inward penetration beyond the top of the pedestal both increase. This leads to a transition from small ELMs to large ELMs. Both inward and outward turbulence spreading are sensitive to the scrape-off-layer (SOL) plasma profiles. The inward turbulence spreading increases for the steep SOL profiles, leading to increasing pedestal energy loss in the small ELM regime. The SOL width (λ q ) is significantly broadened progressing from the ELM-free to small ELM regime, due to the onset of strong radial turbulent transport. The extent of the SOL width (λ q ) broadening depends strongly on outward turbulence spreading. The fluctuation energy intensity flux Γ ε at the separatrix can be enhanced by increasing either pedestal E r flow shear or local SOL pressure gradient. The λ q is broadened as the fluctuation energy intensity flux Γ ε at the last close flux surface (LCFS) increases. Local SOL E × B flow shear will restrain outward turbulence spreading and the associated heat flux width broadening. Operating in H-mode with small ELMs has the potential to solve two critical problems: reducing the ELM size and broadening the SOL width.
Long-pulse high-performance H-mode plasmas achieved on EAST
A record duration of a 310 s H-mode plasma (H 98y2 ~ 1.3, n e /n GW ~ 0.7, f BS > 50%) has been recently achieved on experimental advanced superconducting tokamak (EAST) with metal walls, exploiting the device's improved long-pulse capabilities. The experiment demonstrates good control of tungsten concentration, core/edge MHD stability, and particle and heat exhaust with an ITER-like tungsten divertor and zero injected torque, establishing a milestone on the path to steady-state long-pulse high-performance scenarios in support of ITER and CFETR. Important synergistic effects are leveraged toward this result, which relies purely on radio frequency (RF) powers for heating and current drive (H&CD). On-axis electron cyclotron heating enhances the H&CD efficiency from lower hybrid wave injection, increasing confinement quality and enabling fully non-inductive operation at high density (n e /n GW ~ 70%) and high poloidal beta (β P ~ 2.5). A small-amplitude grassy edge localized mode regime facilitates the RF power coupling to the H-mode edge and reduces divertor sputtering/erosion. The high energy confinement quality (H 98y2 ~ 1.3) is achieved with the experimental and simulated results pointing to the strong effect of Shafranov shift on turbulence. Transport analysis suggests that trapped electron modes dominate in the core region during the record discharge. The detailed physics processes (RF synergy, core-edge integration, confinement properties, etc.) of the steady-state operation will be illustrated in the content. In the future, EAST will aim at accessing more relevant dimensionless parameters to develop long-pulse high-performance plasma toward ITER and CFETR steady-state advanced operation.
Impact of pedestal density gradient and collisionality on ELM dynamics
BOUT++ turbulence simulations are conducted to capture the underlying physics of small ELM characteristics achieved by increasing separatrix density via controlling strike points from vertical to horizontal divertor plates for three EAST discharges. BOUT++ linear simulations show that the most unstable modes change from high-n ideal ballooning modes to intermediate-n peeling–ballooning modes and eventually to peeling–ballooning stable plasmas in the pedestal. Nonlinear simulations show that the fluctuation is saturated at a high level for the lowest separatrix density. The ELM size decreases with increasing separatrix density, until the fraction of this energy lost during the ELM crash becomes less than 1% of the pedestal stored energy, leading to small ELMs. Simulations indicate that small ELMs can be triggered either by the marginally peeling–ballooning instability near the peak pressure gradient position inside the pedestal or by a local instability in the pedestal foot with a larger separatrix density gradient. The pedestal collisionality scan for type-I ELMs with steep pedestal density gradient shows that both linear growth rate and ELM size decrease with increasing collisionality. On the contrary, the pedestal collisionality and pedestal density width scan with a weak pedestal density gradient indicate small ELMs can either be triggered by a high-n ballooning mode or by a low-n peeling mode in a low collisionality region 0.04–0.1. We report the simulations indicate the weaker the linear unstable modes near marginal stability with small linear growth rate, the lower nonlinearly saturated fluctuation intensity and the smaller turbulence spreading from the linear unstable zone to stable zone in the nonlinear saturation phase, leading to small ELMs.
Physical mechanisms for the transition from type-III to large ELMs induced by impurity injection on EAST
Transition from type-III to large-amplitude ELMs induced by neon injection has been observed in the EAST tokamak at overlapping q 95 space between large and small ELMs. With neon injection, pedestal density gradient shows a remarkable increase accompanied by some decrease of pedestal electron temperature, and consequently the pressure gradient increases moderately and edge bootstrap current has minimal change. Further experiment demonstrates that the occurrence of large ELMs after neon injection is highly correlated with the change in edge density. Linear peeling-ballooning stability analysis indicates that the large ELM case is more unstable than the type-III ELM case during the ELM transition. A scan of pedestal density gradient in linear stability analysis shows that the direct destabilizing effect of steep pedestal density gradient on peeling-ballooning instabilities via two-fluid effects could also facilitate the transition to large ELMs. In conclusion, these results could provide more insight into the role of pedestal density gradient on pedestal stability and ELM behavior.
Investigations of LHW-plasma coupling and current drive at high density related to H-mode experiments in EAST
Two important issues in achieving lower hybrid current drive (LHCD) high confinement plasma in EAST are to improve lower hybrid wave (LHW)-plasma coupling and to drive the plasma current at a high density. Studies in different configurations with different directions of toroidal magnetic field (Bt) show that the density near the antenna is affected by both the radial electric field induced by plasma without a LHW (Er-plasma) in the scrape off layer (SOL), and the radial electric field induced by LHW power (Er-LH) near the grill. Investigations indicate that Er× Btin the SOL leads to a different effect of configuration on the LHW-plasma coupling and Er-LH× Btaccounts for the asymmetric density behaviour in the SOL observed in the experiments, where Eris the total radial electric field in the SOL. Modelling of parametric instability (PI), collisional absorption (CA) and scattering from density fluctuations (SDF) in the edge region, performed considering the parameters of high density LHCD experiments in EAST, has shown that these mechanisms could be responsible for the low current drive (CD) efficiency at high density. Radiofrequency probe spectra, useful for documenting PI occurrence, show sidebands whose amplitude in the case of the lithiated vacuum chamber is smaller than in the case of poor lithiation, consistently with growth rates from PI modeling of the respective reference discharges. Since strong lithiation is also expected to diminish the parasitic effect on the LHCD of the remaining possible mechanisms, this appears to be a useful method for improving LHCD efficiency at a high density.
High level of integration of front-end imaging optics system for electron cyclotron emission imaging diagnostics on the DIII-D tokamak
The optics system of the Electron Cyclotron Emission Imaging (ECEI) diagnostics on the DIII-D tokamak has been developed and installed for high-resolution temperature fluctuations measurement in the previous decade. The System-on-Chip approach upgrade was finished in June 2019 with high integrated receiver array with 20 individual modules. In this paper, we design new optics with high-level integration. In the new optics system, there will be two mirrors from plasma to receiver array, including one replaceable curved mirror out of the vacuum and one fixed curved mirror in the vessel. There are two options with 1:1 and 1:2 magnifications for high poloidal resolution and larger poloidal window modes. Overall, the new optics system has multiple improvements, including lighter weight, smaller size, more flexible installation and alignment. The synthetic ECEI module is used to evaluate the new optics system.
Design and characterization of a single-channel microwave interferometer for the Helicon Physics Prototype eXperiment
A heterodyne interferometer for measuring the plasma electron density in Helicon Physics Prototype eXperiment (HPPX) has been developed and characterized in the laboratory. The heterodyne-type interferometer uses a probing beam of 85 GHz and a reference beam of 85.7 GHz by using two Gunn oscillators for facilitating frequency modulation. The cutoff density for this frequency is 8.96 x 10 19 m –3 that is much higher than the nominal electron density of the HPPX plasmas. The maximum deflection angle due to the refraction effect is estimated to be 0.63° assuming a parabolic electron density profile, and the impact on the measurement is negligible for the plasmas with a size of 100 mm. Two identical HDPE lenses act as the vacuum windows, and the lenses working together with the transmitter and receiver horns, form a beam with the beam waist of about 20 mm located at the plasma center. The characterization results of the lens and the critical microwave components show good performance. The plasma electron density measurement results are in line with the expectation. Furthermore, the Signal to Noise Ratio (SNR) of the measurement is defined as SNR = 20lg($\bar{n}_{e}$/S), where $\bar{n}_{e}$ and S are respectively the average electron density and the standard deviation of the signal, and the SNR is 80 dB. Finally, this demonstrates the system's capability of providing a clear and detailed density resolution.
Sustained edge-localized-modes suppression and radiative divertor with an impurity-driven instability in tokamak plasmas
We report simultaneous control of the large edge localized modes (ELMs) and divertor heat fluxes in a metal wall environment is a critical issue for steady-state operation of a tokamak fusion reactors. Here we report a sustained ELM suppression scenario achieved in the EAST tokamak compatible with radiative divertor using different seeding impurity species over a wide range of conditions. A low-n mode appears, as manifested by the oscillations of a radiation front near the X-point. This mode appears to drive strong particle transport and tungsten exhaust, which is essential to the maintenance of the ELM-stable state. We have developed a model to explain the mode excitation, by coupling the impurity radiative condensation instability to drift waves, which could explain some characteristics of the low-n mode well. The low-n mode may offer a new ELM-stable scenario compatible with radiative divertor for future fusion reactors.
Effects of radial transport on divertor power and particle flux widths under different operational regimes in EAST
Here, a study of the effects of radial transport on the outer divertor particle and power flux widths (λ js and λ q ) is carried out using plasmas under different operational regimes in the Experimental Advanced Superconducting Tokamak (EAST). In the EAST experiments, the λ js values measured during the grassy intra- and inter-ELM phases are similar, and the averaged value of λ js during grassy ELMy discharges is found to be smaller than that of the intra-ELM phase of type-I ELMy discharges but larger than that of the inter-ELM phase of type-I ELMy discharges. Simulations of scans of the radial particle and heat transport coefficients, D and χ e , performed using the BOUT++ transport code show that both λq and λjs increase with D and χe, especially when D or χ e is larger than a threshold value, indicating that background turbulence starts to matter in the determination of λ q and λ js when D or χ e surpasses the threshold value. A comparison between the simulation of the D scan and the experimental results shows that the different values of λ js obtained under different plasma operational regimes are probably due to the different intensities of background turbulence, which is beyond the scope of Goldston's heuristic drift-based model as reported by Goldston et al (2012 Nucl. Fusion 52 013009), since their model was derived by assuming that turbulent transport does not exceed a certain level. The ratio of λ js to λ q is greatly affected by the radial transport; however, simulations carried out using Scrape-off Layer Plasma Simulation (SOLPS) show that divertor geometry and plasma density have big influences on λ js , and thus could also affect the ratio of λ js to λ q .
Enhancement of edge turbulence concomitant with ELM suppression during boron powder injection in EAST
A reproducible, quasi-stationary edge localized mode (ELM)-suppressed scenario was obtained over a wide range of plasma parameters by continuous injection of boron (B) powder into an upper-single null discharge in the experimental advanced superconducting tokamak [Sun et al., Nucl. Fusion 61, 014002 (2021)]. This powder-induced ELM-absent regime is associated with an edge harmonic mode (EHM) that provides continuous particle exhaust to maintain constant density without confinement degradation and impurity accumulation, the latter of which is often observed in ELM-free regimes. A flow rate threshold of B powder injection, leading to a threshold intensity of the EHM, is necessary for full ELM suppression. The fundamental harmonic of the EHM exhibits a toroidal mode number n = 1. The mode is observable in the entire poloidal cross section with a peak near the upper X-point in an upper-single null configuration. Here, the EHM spans radially across the pedestal and scrape-off layer, peaking inside the separatrix. The EHM appears to be insensitive to q 95 , heating power, plasma toroidal rotation, and pedestal collisionality.
Type-I ELM mitigation by continuous lithium granule gravitational injection into the upper tungsten divertor in EAST
Large edge-localized modes (ELMs) were mitigated by gravitational injection of lithium granules into the upper X-point region of the experimental advanced superconducting tokamak (EAST) device with tungsten plasma-facing components. The maximum ELM size was reduced by ~70% in high β N H-mode plasmas. Large ELM stabilization was sustained for up to about 40 energy confinement times, with constant core radiated power and no evidence of high-Z or low-Z impurity accumulation. The lithium granules injection reduced the edge plasma pedestal density and temperature and their gradients, due to increased edge radiation and reduced recycling from the plasma-facing components. Ideal stability calculations using the ELITE code indicate that the stabilization of large ELMs correlates with improved stability of intermediate-n peeling-ballooning modes, due to reduced edge current resulting from the profile changes. The pedestal pressure reduction was partially offset by a core density increase, which resulted in a modest ~7% drop in core stored energy and normalized energy confinement time. We surmise that the remnant small ELMs are triggered by the penetration of multiple Li granules just past the separatrix, similar to small ELMs triggered by deuterium pellet Futatani et al (2014 Nucl. Fusion 54 073008). This study extends previous ELM elimination with Li powder injection Maingi et al (2018 Nucl. Fusion 58 024003) in EAST because (1) use of small, dust-like powder and the related potential health hazards were eliminated, and (2) use of macroscopic granules should be more applicable to future devices, due to deeper penetration than dust particles, e.g. inside the separatrix with velocities ~10 m s -1 in EAST.
Observation of fully detached divertor integrated with improved core confinement for tokamak fusion plasmas
Integration of divertor detachment with a high-performance (β N ~ 3, β p > 2, H 98 ~ 1.5) core plasma has been demonstrated in DIII-D high-β p (poloidal beta) plasmas associated with a sustained core internal transport barrier (ITB) and an H-mode edge transport barrier (ETB). Such good core-edge integration has been achieved for both neon and nitrogen seeding, for both favorable and unfavorable B-field directions, independently from the impurity puffing locations, though these variations play important roles on divertor characteristics. Compared to the standard H-mode plasmas, the high-β p plasma exhibits a much wider window of detachment compatible with high confinement core. Fully detached divertor plasmas with low plasma temperature (Te < 5 eV), low particle flux, and low heat flux across the entire divertor target plate were obtained by using nitrogen seeding. This detached high-β p plasma is compatible with a newly developed detachment control system which can help optimize the nitrogen gas flow rate. Several features, i.e., the high edge safety factor in the high-β p scenario, impurity injection, closed divertor and reduced heating power requirement due to the high confinement, facilitate the achievement of full divertor detachment at lower density. Instead of degrading global performance, the divertor detachment facilitates the access to an even stronger ITB at large radius with a relatively weak ETB through self-organized synergy between ITB and ETB, leading to sustained high confinement. The strengthening of the large-radius ITB compensates for the ETB degradation associated with divertor detachment. In addition, a weak ETB naturally has smaller edge localized modes (ELMs). In particular, with neon injection, a long-period no-ELM H-mode phase has been achieved simultaneously with high-performance core and partially detached divertor plasmas. Furthermore, these results demonstrate the possibility of integrating excellent core plasma performance with an effective divertor solution, an essential step toward steady-state operation of reactor-grade plasmas.
Advances in physics understanding of high poloidal beta regime toward steady-state operation of CFETR
Experimental and modeling investigations of the high βp scenarios on the DIII-D and EAST tokamaks show advantages in high energy confinement, avoidance of n = 1 MHD, and core-edge integration with reduced heat flux, making this scenario an attractive option for CFETR steady-state operation. Experiments show that plasmas with high confinement and high density can be achieved with neutral beam injection on DIII-D (β p ~ 2.2, β N ~ 3.5, f BS ~ 50%, f Gw ~ 1.0, H 98y2 ~ 1.5) and pure RF power on EAST (β P ~ 2.0, β N ~ 1.6, f BS ~ 50%, f Gw ~ 0.8, H 98y2 > 1.3). By tailoring the current density profile, a q-profile with local (off-axis) negative shear is achieved that yields improved confinement and MHD stability. Transport analysis and simulation suggest that the combination of high density gradient and high Shafranov shift allows turbulence stabilization and higher confinement. Using on-axis ECH injection, tungsten accumulation is avoided on EAST, and this is reproduced in modeling. Reduced heat flux (by >40%) and maintenance of high core confinement is achieved with active feedback control of the radiated divertor, an important result for long pulse operation in tokamaks. In conclusion, the improved physics understanding and validated modeling tools are used to design a 1GW steady-state scenario for CFETR.
Progress of Divertor Heat and Particle Flux Control in EAST for Advanced Steady-State Operation in the Last 10 Years
Active control of the excessively high heat and particle fluxes on the divertor target plates is of fundamental importance to the steady state operation of tokamaks, especially for fusion reactors. A series of experiments have been carried out on this critical issue to relieve the plasma-wall interactions in the experimental advanced superconducting tokamak (EAST) in the last ten years, not only contributing to the long pulse operation of EAST itself, but also providing physical understandings and potential techniques to the next-generation devices like ITER. Here we have characterized the power deposition pattern and broadened the divertor footprint width effectively. The plasma-wetted area is actively handled using either 3-dimentional edge magnetic topology or advanced plasma equilibrium, thereby peak heat flux around the strike point is reduced. Active control of detachment or radiation compatible with core plasma performance has progressed significantly in very recent years, with a series of active feedback control modules developed and utilized successfully, based on the divertor physics advances with both experiments and simulation. The upper divertor of EAST was upgraded from graphite to active water-cooling ITER-like tungsten in 2014, exhibiting much enhanced heat removal capability. As for the particle exhaust including both fueling and impurity particles, in addition to wall conditioning and impurity source control, the efficiency of particle flux exhaust is optimized by making full use of the divertor closure and the plasma drifts in both scrape-off layer and divertor volume. These heat and particle exhaust advances contribute greatly to a series of EAST achievements like H-mode operation over 100 s. A brief near-term plan on the integrated control of divertor plasma-wall interactions in long-time scale will also be introduced, aiming to provide favorable divertor operation solution for ITER and CFETR.
Integration of full divertor detachment with improved core confinement for tokamak fusion plasmas
Divertor detachment offers a promising solution to the challenge of plasma-wall interactions for steady-state operation of fusion reactors. Here, we demonstrate the excellent compatibility of actively controlled full divertor detachment with a high-performance (β N ~ 3, H 98 ~ 1.5) core plasma, using high-β p (poloidal beta, β p > 2) scenario characterized by a sustained core internal transport barrier (ITB) and a modest edge transport barrier (ETB) in DIII-D tokamak. The high-β p high-confinement scenario facilitates divertor detachment which, in turn, promotes the development of an even stronger ITB at large radius with a weaker ETB. This self-organized synergy between ITB and ETB, leads to a net gain in energy confinement, in contrast to the net confinement loss caused by divertor detachment in standard H-modes. These results show the potential of integrating excellent core plasma performance with an efficient divertor solution, an essential step towards steady-state operation of reactor-grade plasmas.
Grassy ELM regime at low pedestal collisionality in high-power tokamak plasma
Spontaneous mitigation of giant ELMs and appearance of grassy ELMs have been observed repeatedly at low pedestal collisionality (${\nu }_{\mathrm{e},\mathrm{p}\mathrm{e}\mathrm{d}}^{{\ast}}\sim 0.15$) in the high-power (P inj > 13 MW) hybrid scenario in DIII-D. Higher β p and higher q 95 appear to be beneficial to achieving the grassy ELM regime. The grassy ELM H-mode plasma shows high energy confinement performance (H 98y2 up to over 1.5) under the conditions of high neutral beam torque and high core rotation. The pedestal width appears to exceed the EPED1.0 model prediction by more than 50%. Pedestal stability analysis performed with the ELITE code indicates that the stability against low-n kink/peeling modes is improved with increased auxiliary heating power and the operational point in the grassy ELM regime is located near the ballooning boundary. The pedestal stability characteristics during the grassy ELM crashes have been investigated in comparison with the giant ELM crashes based on plasma profiles experimentally measured with high resolution and accuracy. It has been found that the underlying mechanism for the observed small-amplitude ELM crashes is mainly the expansion of the ballooning stability boundary induced by an initial radially localized collapse in the pedestal, which helps to stop the growth of instabilities and further collapse of the pedestal. The effect of electron density pedestal on mitigating edge localized instabilities has been analyzed by numerical simulation, suggesting that the electron density pedestal characterized by high n e,sep /n e,ped and low density gradient helps to stabilize peeling-ballooning modes because of a low pressure pedestal gradient and to lower the ballooning boundary mainly because of a low ion diamagnetic frequency in the pedestal region, thus triggering ballooning instabilities and producing the intrinsic grassy ELMs. Numerical simulation of the Chinese fusion engineering test reactor (CFETR) with the SOLPS code indicates that the separatrix density might be insensitive to the electron diffusivity in the pedestal region and increase with the power flowing from the core region to the edge region. Furthermore, pedestal stability analysis suggests that the flat density pedestal with high separatrix density obtained in the high-power plasma in CFETR would make the operational point close to the ballooning boundary, which is considered to help destabilize ballooning instabilities and facilitate the access to the grassy ELM regime.
Suppression of edge localized modes with real-time boron injection using the tungsten divertor in EAST
We report an observation of robust suppression of edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST), enabled by continuous boron (B) powder injection. Edge harmonic oscillations appear during B powder injection, providing sufficient particle transport to maintain constant density and avoid impurity accumulation in ELM-stable plasmas. Here, quasi-steady ELM suppression discharges are demonstrated with modest energy confinement improvement and over a wide range of conditions: heating power and technique variation, electron density range over a factor ~3.5, deuterium or helium ion species, and with either direction of the toroidal magnetic field. ELM suppression is observed above a threshold edge B intensity and ceases within 0.5 s of termination of the B injection. In contrast to ELM suppression accompanied by recycling reduction during Li powder injection in NSTX and EAST (Maingi et al 2018 Nucl. Fusion 58 024003), reduced recycling due to hydrogenic species retention is unnecessary for the ELM suppression with B powder injection, paving the way for its consideration as an ELM control tool for future fusion devices.