Engineering topics

Xu, Gui‐Liang

Publications and source records attributed to Xu, Gui‐Liang.

16 records

DOE OSTI2024

High–Energy Earth–Abundant Cathodes with Enhanced Cationic/Anionic Redox for Sustainable and Long–Lasting Na–Ion Batteries

Layered iron/manganese-based oxides are a class of promising cathode materials for sustainable batteries due to their high energy densities and earth abundance. However, the stabilization of cationic and anionic redox reactions in these cathodes during cycling at high voltage remain elusive. Here, an electrochemically/thermally stable P2-Na 0.67 Fe 0.3 Mn 0.5 Mg 0.1 Ti 0.1 O 2 cathode material with zero critical elements is designed for sodium-ion batteries (NIBs) to realize a highly reversible capacity of ≈210 mAh g –1 at 20 mA g –1 and good cycling stability with a capacity retention of 74% after 300 cycles at 200 mA g –1 , even when operated with a high charge cut-off voltage of 4.5 V versus sodium metal. Combining a suite of cutting-edge characterizations and computational modeling, it is shown that Mg/Ti co-doping leads to stabilized surface/bulk structure at high voltage and high temperature, and more importantly, enhances cationic/anionic redox reaction reversibility over extended cycles with the suppression of other undesired oxygen activities. This work fundamentally deepens the failure mechanism of Fe/Mn-based layered cathodes and highlights the importance of dopant engineering to achieve high-energy and earth-abundant cathode material for sustainable and long-lasting NIBs.

25 ENERGY STORAGE↗

DOE OSTI2024

Protonation Stimulates the Layered to Rock Salt Phase Transition of Ni‐Rich Sodium Cathodes

Abstract Protonation of oxide cathodes triggers surface transition metal dissolution and accelerates the performance degradation of Li‐ion batteries. While strategies are developed to improve cathode material surface stability, little is known about the effects of protonation on bulk phase transitions in these cathode materials or their sodium‐ion battery counterparts. Here, using NaNiO 2 in electrolytes with different proton‐generating levels as model systems, a holistic picture of the effect of incorporated protons is presented. Protonation of lattice oxygens stimulate transition metal migration to the alkaline layer and accelerates layered‐rock‐salt phase transition, which leads to bulk structure disintegration and anisotropic surface reconstruction layers formation. A cathode that undergoes severe protonation reactions attains a porous architecture corresponding to its multifold performance fade. This work reveals that interactions between electrolyte and cathode that result in protonation can dominate the structural reversibility/stability of bulk cathodes, and the insight sheds light for the development of future batteries.

25 ENERGY STORAGE↗

DOE OSTI2023

Implanting Transition Metal into Li 2 O-Based Cathode Prelithiation Agent for High-Energy-Density and Long-Life Li-Ion Batteries

Compensating the irreversible loss of limited active lithium (Li) is essentially important for improving the energy-density and cycle-life of practical Li-ion battery full-cell, especially after employing high-capacity but low initial coulombic efficiency anode candidates. Introducing prelithiation agent can provide additional Li source for such compensation. Herein, we precisely implant trace Co (extracted from transition metal oxide) into the Li site of Li 2 O, obtaining (Li 0.66 Co 0.11$\square$0.23 ) 2 O (CLO) cathode prelithiation agent. Further, the synergistic formation of Li vacancies and Co-derived catalysis efficiently enhance the inherent conductivity and weaken the Li-O interaction of Li 2 O, which facilitates its anionic oxidation to peroxo/superoxo species and gaseous O 2 , achieving 1642.7 mAh/g ~Li2O prelithiation capacity (≈980 mAh/g for prelithiation agent). Coupled 6.5 wt % CLO-based prelithiation agent with LiCoO 2 cathode, substantial additional Li source stored within CLO is efficiently released to compensate the Li consumption on the SiO/C anode, achieving 270 Wh/kg pouch-type full-cell with 92 % capacity retention after 1000 cycles.

25 ENERGY STORAGE↗

DOE OSTI2023

Regulating Li Nucleation and Growth Heterogeneities via Near-Surface Lithium-Ion Irrigation for Stable Anode-Less Lithium Metal Batteries

The inhomogeneous nucleation and growth of Li dendrite combined with the spontaneous side reactions with the electrolytes dramatically challenge the stability and safety of Li metal anode (LMA). Despite tremendous endeavors, current success relies on the use of significant excess of Li to compensate the loss of active Li during cycling. Herein, a near-surface Li + irrigation strategy is developed to regulate the inhomogeneous Li deposition behavior and suppress the consequent side reactions under limited Li excess condition. The conformal polypyrrole (PPy) coating layer on Cu surface via oxidative chemical vapor deposition technique can induce the migration of Li + to the interregional space between PPy and Cu, creating a near-surface Li + -rich region to smooth diffusion of ion flux and uniform the deposition. Moreover, as evidenced by multiscale characterizations including synchrotron high-energy X-ray diffraction scanning, a robust N-rich solid-electrolyte interface (SEI) is formed on the PPy skeleton to effectively suppress the undesired SEI formation/dissolution process. Strikingly, stable Li metal cycling performance under a high areal capacity of 10 mAh cm -2 at 2.0 mA cm -2 with merely 0.5 × Li excess is achieved. The findings not only resolve the long-standing poor LMA stability/safety issues, but also deepen the mechanism understanding of Li deposition process.

25 ENERGY STORAGE↗

DOE OSTI2023

Suppressing Universal Cathode Crossover in High‐Energy Lithium Metal Batteries via a Versatile Interlayer Design**

Abstract The universal cathode crossover such as chemical and oxygen has been significantly overlooked in lithium metal batteries using high‐energy cathodes which leads to severe capacity degradation and raises serious safety concerns. Herein, a versatile and thin (≈25 μm) interlayer composed of multifunctional active sites was developed to simultaneously regulate the Li deposition process and suppress the cathode crossover. The as‐induced dual‐gradient solid‐electrolyte interphase combined with abundant lithiophilic sites enable stable Li stripping/plating process even under high current density of 10 mA cm −2 . Moreover, X‐ray photoelectron spectroscopy and synchrotron X‐ray experiments revealed that N‐rich framework and CoZn dual active sites can effectively mitigate the undesired cathode crossover, hence significantly minimizing Li corrosion. Therefore, assembled lithium metal cells using various high‐energy cathode materials including LiNi 0.7 Mn 0.2 Co 0.1 O 2 , Li 1.2 Co 0.1 Mn 0.55 Ni 0.15 O 2 , and sulfur demonstrate significantly improved cycling stability with high cathode loading.

Xie, Chuyi↗

DOE OSTI2023

Suppressing Universal Cathode Crossover in High‐Energy Lithium Metal Batteries via a Versatile Interlayer Design**

25 ENERGY STORAGE↗

DOE OSTI2022

A Fast‐Charging and High‐Temperature All‐Organic Rechargeable Potassium Battery

Abstract Developing fast‐charging, high‐temperature, and sustainable batteries is critical for the large‐scale deployment of energy storage devices in electric vehicles, grid‐scale electrical energy storage, and high temperature regions. Here, a transition metal‐free all‐organic rechargeable potassium battery (RPB) based on abundant and sustainable organic electrode materials (OEMs) and potassium resources for fast‐charging and high‐temperature applications is demonstrated. N‐doped graphene and a 2.8 m potassium hexafluorophosphate (KPF 6 ) in diethylene glycol dimethyl ether (DEGDME) electrolyte are employed to mitigate the dissolution of OEMs, enhance the electrode conductivity, accommodate large volume change, and form stable solid electrolyte interphase in the all‐organic RPB. At room temperature, the RPB delivers a high specific capacity of 188.1 mAh g −1 at 50 mA g −1 and superior cycle life of 6000 and 50000 cycles at 1 and 5 A g −1 , respectively, demonstrating an ultra‐stable and fast‐charging all‐organic battery. The impressive performance at room temperature is extended to high temperatures, where the high‐mass‐loading (6.5 mg cm −2 ) all‐organic RPB exhibits high‐rate capability up to 2 A g −1 and a long lifetime of 500 cycles at 70–100 °C, demonstrating a superb fast‐charging and high‐temperature battery. The cell configuration demonstrated in this work shows great promise for practical applications of sustainable batteries at extreme conditions.

25 ENERGY STORAGE↗

DOE OSTI2022

Thermal Runaway of Nonflammable Localized High‐Concentration Electrolytes for Practical LiNi 0.8 Mn 0.1 Co 0.1 O 2 |Graphite‐SiO Pouch Cells

Abstract With continuous improvement of batteries in energy density, enhancing their safety is becoming increasingly urgent. Herein, practical high energy density LiNi 0.8 Mn 0.1 Co 0.1 O 2 |graphite‐SiO pouch cell with nonflammable localized high concentration electrolyte (LHCE) is proposed that presents unique self‐discharge characteristic before thermal runaway (TR), thus effectively reducing safety hazards. Compared with the reference electrolyte, pouch cell with nonflammable LHCE can increase self‐generated heat temperature by 4.4 °C, increase TR triggering temperature by 47.3 °C, decrease the TR highest temperature by 71.8 °C, and extend the time from self‐generated heat to triggering TR by ≈8 h. In addition, the cell with nonflammable LHCE presents superior high voltage cycle stability, attributed to the formation of robust inorganic‐rich electrode–electrolyte interphase. The strategy represents a pivotal step forward for practical high energy and high safety batteries.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

Abstract The commercialization of lithium–sulfur (Li−S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li stripping/plating reversibility. Herein, we report an effective strategy by combining Se‐doped S hosted in an ordered macroporous framework with a highly fluorinated ether (HFE)‐based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of >5.4 mAh cm −2 with high Coulombic efficiency >99.2 % can be achieved under high areal Se/S loading (5.8 mg cm −2 ), while the underlying mechanism was further revealed through synchrotron X‐ray probes and Time‐of‐Flight Secondary Ion Mass Spectrometry (ToF‐SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (>5.0 mg cm −2 ) and thin Li metal (40 μm).

Zhao, Chen↗

DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

The commercialization of lithium-sulfur (Li-S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li striping/platting reversibility. We reported an effective strategy by combining Se-doped S hosted in an ordered macroporous framework with highly fluorinated ether (HFE)-based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of > 5.4 mAh cm -2 with high coulombic efficiency > 99.2% can be achieved under high areal Se/S loading (5.8 mg cm -2 ), while the underlying mechanism was further revealed through synchrotron X-ray probes and Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (> 5.0 mg cm -2 ) and thin Li metal (40 µm).

25 ENERGY STORAGE↗

DOE OSTI2021

High-Voltage and High-Safety Practical Lithium Batteries with Ethylene Carbonate-Free Electrolyte

Serious safety issues are impeding the widespread adoption of high-energy lithium-ion batteries for transportation electrification and large-scale grid storage. Herein, a triple-salt ethylene carbonate (EC) free electrolyte for high-safety and high-energy pouch-type LiNi 0.8 Mn 0.1 Co 0.1 O 2 |graphite (NMC811|Gr) cells is reported. This EC-free electrolyte can effectively stabilize the NMC811 surface under high potential (up to 4.5 V), as well as generate a stable interphase to achieve a superior compatibility with the Gr anode. The electrolyte strategy enables significantly enhanced intrinsic safety (trigger temperature of thermal runaway (TR) increased by 67.0 °C), excellent electrochemical properties (4.2V, ≈100% after 200 cycles), and superior high voltage stability (4.5 V, 82.1% after 200 cycles). Furthermore, the work opens up a new avenue for developing novel electrolyte systems to build safer high-energy batteries for practical applications.

25 ENERGY STORAGE↗

DOE OSTI2021

Multiscale Understanding of Surface Structural Effects on High-Temperature Operational Resiliency of Layered Oxide Cathodes

The worldwide energy demand in electric vehicles and the increasing global temperature have called for development of high-energy and long-life lithium-ion batteries (LIBs) with improved high temperature operational resiliency. However, current attention has been mostly focused on cycling aging at elevated temperature, leaving considerable gaps of knowledge in the failure mechanism and practical control of abusive calendar aging and thermal runaway that are highly related to the eventual operational lifetime and safety performance of LIBs. Herein, using a combination of various in situ synchrotron X-ray and electron microscopy techniques, we report a multiscale understanding of surface structure effects involved in regulating the high temperature operational tolerance of polycrystalline Ni-rich layered cathodes. Our results collectively show that an ultraconformal poly (3,4-ethylenedioxythiophene) coating can effectively prevent LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathode from undesired phase transformation and transition metal dissolution on the surface, atomic displacement and dislocations within primary particles, intergranular cracking along the grain boundaries within secondary particles, and intensive bulk oxygen release during high state-of-charge and high temperature aging. As a result, the present work highlights the essential role of surface structure controls in overcoming the multiscale degradation pathways of high-energy battery materials at extreme temperature.

25 ENERGY STORAGE↗

DOE OSTI2021

Simultaneously Blocking Chemical Crosstalk and Internal Short Circuit via Gel-Stretching Derived Nanoporous Non-Shrinkage Separator for Safe Lithium-Ion Batteries

The separator, an ionic permeable and electronic insulating membrane between cathode and anode, plays a crucial role in the electrochemical and safety performance of batteries. However, the commercial polyolefin separators not only suffer from inevitable thermal shrinkage at elevated temperature, but also fail to inhibit the hidden chemical crosstalk of reactive gases such as O 2 , leading to often reported thermal runaway (TR) and hence preventing large-scale implementation of high-energy-density lithium-ion batteries. Herein, a nanoporous non-shrinkage separator (GS-PI) was fabricated via a novel gel-stretching orientation approach to eliminate TR. In situ synchrotron small angle X-ray scattering during heating clearly showed that the as-prepared thin GS-PI separator exhibits superior mechanical tolerance at high temperature, thus effectively preventing internal short circuit. Meanwhile, the unique nanoporous structure design further blocks chemical crosstalk and the associated exothermic reactions. Accelerating Rate Calorimetry test revealed that the practical 1 Ah LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622)/graphite pouch cell using GS-PI nanoporous separator show a maximum temperature rise (dT/dt max ) of only 3.7 °C s -1 compared to 131.6 °C s -1 in the case of Al 2 O 3 @PE macroporous separator. Furthermore, despite the reduced pore size, the GS-PI separator demonstrates better cycling stability than conventional Al 2 O 3 @PE separator at high temperature without sacrificing specific capacity and rate capability.

25 ENERGY STORAGE↗

DOE OSTI2021

Electrolytes Polymerization‐Induced Cathode‐Electrolyte‐Interphase for High Voltage Lithium‐Ion Batteries

Abstract Lithium‐ion batteries (LIBs) based on LiNi x Co y Mn 1‐x‐y O 2 (NCM) cathode materials have been widely commercialized, because of their high energy density, favorable rate performance, and relatively low cost. However, with increased Ni content to further increase their energy density, their cycling stability deteriorates dramatically and thus fails to meet the commercial application requirements. The artificial cathode‐electrolyte‐interphase (CEI) is a promising approach to solve this problem. Here, a robust CEI is fabricated through in situ polymerization of ethylene carbonate induced by aluminum isopropoxide (AIP). By adding 1 wt.% AIP in a commercial electrolyte, the capacity retention of LiNi 0.8 Co 0.1 Mn 0.1 O 2 ||Li cell at 1 C rate has been significantly increased from 80.8% to 97.8% with a highly reversible capacity of 176 mA h g −1 after 200 cycles. AIP can be also used as an additive during the slurry‐making process, enabling a reversible capacity of 170 mA h g −1 for LiCoO 2 after 200 cycles even at a high charge cut‐off voltage of 4.6 V. It is confirmed that the in situ formed CEI layer can prevent the cathodes from cracking and reduce the irreversible phase transformation.

Yang, Jixiang↗

DOE OSTI2021

Enabling High-Performance NASICON-Based Solid-State Lithium Metal Batteries Towards Practical Conditions

Solid-state lithium metal batteries (SSLMBs) are promising next-generation high-energy rechargeable batteries. However, the practical energy densities of the reported SSLMBs have been significantly overstated due to the use of thick solid-state electrolytes, thick lithium (Li) anodes, and thin cathodes. Here, a high-performance NASICON-based SSLMB using a thin (60 µm) Li 1.5 Al 0.5 Ge 1.5 (PO 4 ) 3 (LAGP) electrolyte, ultrathin (36 µm) Li metal, and high-loading (8 mg cm -2 ) LiFePO 4 (LFP) cathode is reported. The thin and dense LAGP electrolyte prepared by hot-pressing exhibits a high Li ionic conductivity of 1 × 10 -3 S cm -1 at 80 °C. The assembled SSLMB can thus deliver an increased areal capacity of ≈1 mAh cm -2 at C/5 with a high capacity retention of ≈96% after 50 cycles under 80 °C. Furthermore, it is revealed by synchrotron X-ray absorption spectroscopy and in situ high-energy X-ray diffraction that the side reactions between LAGP electrolyte and LFP cathode are significantly suppressed, while rational surface protection is required for Ni-rich layered cathodes. This study provides valuable insights and guidelines for the development of high-energy SSLMBs towards practical conditions.

25 ENERGY STORAGE↗

DOE OSTI2021

Vacancy‐Enabled O3 Phase Stabilization for Manganese‐Rich Layered Sodium Cathodes

Abstract Manganese‐rich layered oxide materials hold great potential as low‐cost and high‐capacity cathodes for Na‐ion batteries. However, they usually form a P2 phase and suffer from fast capacity fade. In this work, an O3 phase sodium cathode has been developed out of a Li and Mn‐rich layered material by leveraging the creation of transition metal (TM) and oxygen vacancies and the electrochemical exchange of Na and Li. The Mn‐rich layered cathode material remains primarily O3 phase during sodiation/desodiation and can have a full sodiation capacity of ca. 220 mAh g −1 . It delivers ca. 160 mAh g −1 specific capacity between 2–3.8 V with >86 % retention over 250 cycles. The TM and oxygen vacancies pre‐formed in the sodiated material enables a reversible migration of TMs from the TM layer to the tetrahedral sites in the Na layer upon de‐sodiation and sodiation. The migration creates metastable states, leading to increased kinetic barrier that prohibits a complete O3‐P3 phase transition.

Xiao, Biwei↗