Search NASA⌕ Search

Engineering topics

Xu, Yaobin

Publications and source records attributed to Xu, Yaobin.

66 records · Page 4

Polymer-in-"quasi-ionic liquid" electrolytes for high-voltage lithium metal batteries

Due to the limited oxidation stability (< 4 V) of ether oxygen, PEO-based polymer electrolytes are not compatible with high-voltage (> 4 V) cathodes, restricting the energy density of lithium (Li) metal batteries. Here, we design a new type of polymer in quasi-ionic liquid electrolyte (PQILE) that reduces the lone electron pairs of ether oxygens from PEO and ether solvent, induces the formation of stable interfacial layers on both surfaces of LiNi1/3Mn1/3Co1/3O2 cathode and Li metal anode, resulting in a capacity retention of 88.4%, 86.7% and 79.2% after 300 cycles with the charge cutoff voltage of 4.2, 4.3 and 4.4 V, respectively. It’s promising to use quasi-ionic liquids to design new polymer electrolytes for high-voltage and high-specific-energy Li metal batteries.

Wu, Haiping↗

Origin of lithium whisker formation and growth under stress

Lithium metal has the lowest standard electrochemical redox potential and very high theoretical specific capacity, making it the ultimate anode material for rechargeable batteries. However, its application in batteries has been impeded by the formation of Li whiskers, which consume the electrolyte, deplete active Li and may lead to short-circuit of the battery. Tackling these issues successfully is dependent on acquiring sufficient understanding of the formation mechanisms and growth of Li whiskers under the mechanical constraints of a separator. Here, by coupling an atomic force microscopy cantilever into a solid open-cell set-up in environmental transmission electron microscopy, we directly capture the nucleation and growth behaviour of Li whiskers under elastic constraint. First, we show that Li deposition is initiated by a sluggish nucleation of a single crystalline Li particle, with no preferential growth directions. Remarkably, we find that retarded surface transport of Li plays a decisive role in the subsequent deposition morphology. We then explore the validity of these findings in practical cells using a series of carbonate-poisoned ether-based electrolytes. Finally, we show that Li whiskers can yield, buckle, kink or stop growing under certain elastic constraints.

25 ENERGY STORAGE↗

Nonflammable Electrolytes for Lithium Ion Batteries Enabled by Ultraconformal Passivation Interphases

Occasional fire accidents and continuous battery safety concerns require advanced lithium ion batteries (LIBs) with high safety as well as great battery performances. The electrolyte plays a critical role in electrochemical and safety properties. Organic phosphate solvents next to the state-of-the-art organic carbonates could formulate nonflammable electrolytes and intrinsically eliminate fire hazards, but their poor compatibility with the graphite anodes remains an obstacle for practical applications. This work reports a promising approach by formulating localized high concentration electrolytes based on a phosphate solvent, ethylene carbonate and a partially fluorinated ether. This electrolyte readily generates robust solid electrolyte interphase on graphite anode and cathode electrolyte interphase on LiNi0.8Mn0.1Co0.1O2 (NMC811) cathode. As a result, this electrolyte shows good compatibility with high voltage cathode and graphite anode, and enables long-term cycling stability in graphite||NMC811 cells. This work sheds a new light in development of nonflammable electrolytes for high energy-density LIBs.

Non-flammable electrolyte, lithium ion battery, lo↗

A Coherently Strained Monoclinic [111]PbTiO 3 Film Exhibiting Zero Poisson's Ratio State

Abstract [111]‐Oriented perovskite oxide films exhibit unique interfacial and symmetry breaking effects, which are promising for novel quantum materials as topological insulators and polar metals. However, due to strong polar mismatch and complex structural reconstructions on (111) surfaces/interfaces, it is still challenging to grow high quality [111] perovskite heterostructures, let alone explore the as‐resultant physical properties. Here, the fabrication of ultrathin PbTiO 3 films grown on a SrTiO 3 (111) substrate with atomically defined surfaces, by pulsed laser deposition, is reported. High‐resolution scanning transmission electron microscopy and X‐ray diffraction reveal that the as‐grown [111]PbTiO 3 films are coherent with the substrate and compressively strained along all in‐plane directions. In contrast, the out‐of‐plane lattices are almost unchanged compared with that of bulk PbTiO 3 , resulting in a 4% contraction in unit cell volume and a nearly zero Poisson's ratio. Ferroelectric displacement mapping reveals a monoclinic distortion within the compressed [111]PbTiO 3 , with a polarization larger than 50 µC cm −2 . The present findings, as further corroborated by phase field simulations and first principle calculations, differ significantly from the common [001]‐oriented films. Fabricating oxide films through [111] epitaxy may facilitate the formation of new phase components and exploration of novel physical properties for future electronic nanodevices.

Tang, Yunlong↗

Dynamic imaging of crystalline defects in lithium-manganese oxide electrodes during electrochemical activation to high voltage

Crystalline defects are commonly generated in lithium-metal-oxide electrodes during cycling of lithium-ion batteries. Their role in electrochemical reactions is not yet fully understood because, until recently, there has not been an effective operando technique to image dynamic processes at the atomic level. In this study, two types of defects were monitored dynamically during delithiation and concomitant oxidation of oxygen ions by using in situ high-resolution transmission electron microscopy supported by density functional theory calculations. One stacking fault with a fault vector b/6[110] and low mobility contributes minimally to oxygen release from the structure. In contrast, dissociated dislocations with Burgers vector of c/2[001] have high gliding and transverse mobility; they lead to the formation, transport and release subsequently of oxygen related species at the surface of the electrode particles. This work advances the scientific understanding of how oxygen participates and the structural response during the activation process at high potentials.

36 MATERIALS SCIENCE↗

Thin Film RuO 2 Lithiation: Fast Lithium‐Ion Diffusion along the Interface

Abstract Although lithium‐ion batteries that run on the conversion reaction have high capacity, their cyclability remains problematic due to large volume changes and material pulverization. Dimensional confinement, such as 2D thin film or nanodots in a conductive matrix, is proposed as a way of improving the cyclic stability, but the lithiation mechanism of such dimensionally controlled materials remains largely unknown. Here, by in situ transmission electron microscopy, lithiation of thin RuO 2 films with different thicknesses and directions of lithium‐ion diffusion are observed at atomic resolution to monitor the reactions. From the side‐wall diffusion in ≈4 nm RuO 2 film, the ion‐diffusion and reaction are fast, called “interface‐dominant” mode. In contrast, in ≈12 nm film, the ion diffusion–reaction only occurs at the interface where there is a high density of defects due to misfits between the film and substrate, called the “interface‐to‐film” mode. Compared to the side‐wall diffusion, the reaction along the normal direction of the thin film are found to be sluggish (“layer‐to‐layer” mode). Once lithiation speed is higher, the volume expansion is larger and the intercalation stage becomes shorter. Such observation of preferential lithiation direction in 2D‐like RuO 2 thin film provides useful insights to develop dimensionally confined electrodes for lithium‐ion batteries.

Kim, Sungkyu↗

Morphological Engineering of Winged Au@MoS 2 Heterostructures for Electrocatalytic Hydrogen Evolution

Molybdenum disulfide (MoS 2 ) has been recognized as a promising cost-effective catalyst for water-splitting hydrogen production. However, the desired performance of MoS 2 is often limited by insufficient edge-terminated active sites, poor electrical conductivity, and inefficient contact to the supporting substrate. To address these limitations, we developed a unique nanoarchitecture (namely, winged Au@MoS 2 heterostructures enabled by our discovery of the “seeding effect” of Au nanoparticles for the chemical vapor deposition synthesis of vertically aligned few-layer MoS 2 wings). The winged Au@MoS 2 heterostructures provide an abundance of edge-terminated active sites and are found to exhibit dramatically improved electrocatalytic activity for the hydrogen evolution reaction. Theoretical simulations conducted for this unique heterostructure reveal that the hydrogen evolution is dominated by the proton adsorption step, which can be significantly promoted by introducing sufficient edge active sites. Our study introduces a new morphological engineering strategy to make the pristine MoS 2 layered structures highly competitive earth-abundant catalysts for efficient hydrogen production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Revealing the Effects of Electrode Crystallographic Orientation on Battery Electrochemistry via the Anisotropic Lithiation and Sodiation of ReS 2

Practical application of electrochemical water splitting demands durable, efficient, and non-noble metal catalysts for both hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). Herein, we report a new hydrogen evolution nanowire electrocatalyst, consisting of S-doped CoWP nanoparticles embedded in S- and N-doped carbon matrix (S-CoWP@(S,N)-C), which is in situ transformed from Hofmann-type (Co, W)-based metal–organic framework (MOF) nanowires. Because of S and N doping to the carbon matrix and the S doping to CoWP nanoparticles, the obtained S-CoWP@(S,N)-C catalyst reaches a current density of -10 mA cm –2 at -35 and -67 mV (vs RHE) in acidic and alkaline electrolytes, respectively. Powered by a lead halide perovskite solar cell, an unassisted two-electrode solar water-splitting device using MOF-derived S-CoWP@(S,N)-C HER electrocatalysts and S-CoW@(S,N)-C OER electrocatalysts displays a solar-to-hydrogen conversion efficiency of 10.98%. Our method is highly applicable for developing robust electrocatalysts toward efficient and low-cost solar-driven water splitting.

25 ENERGY STORAGE↗

Melt-Centrifuged (Bi,Sb) 2 Te 3 : Engineering Microstructure toward High Thermoelectric Efficiency

Microstructure engineering is an effective strategy to reduce lattice thermal conductivity (JG) and enhance the thermoelectric figure of merit (zT). Through a new process based on melt-centrifugation to squeeze out excess eutectic liquid, microstructure modulation is realized to manipulate the formation of dislocations and clean grain boundaries, resulting in a porous network with a platelet structure. In this way, phonon transport is strongly disrupted by a combination of porosity, pore surfaces/junctions, grain boundaries, and lattice dislocations. These collectively result in a ≈60% reduction of JG compared to zone melted ingot, while the charge carriers remain relatively mobile across the liquid-fused grains. This porous mate­rial displays a zT value of 1.2, which is higher than fully dense conventional zone melted ingots and hot pressed (Bi,Sb) 2 Te 3 alloys. A segmented leg of melt-centrifuged Bi 0.5 Sb 1.5 Te 3 and Bi 0.3 Sb 1.7 Te 3 could produce a high device ZT exceeding 1.0 over the whole temperature range of 323-523 K and an efficiency up to 9%. Here, we demonstrate a method for synthe­sizing high-efficiency porous thermoelectric materials through an uncon­ventional melt-centrifugation technique.

36 MATERIALS SCIENCE↗

Dynamic imaging of metastable reaction pathways in lithiated cobalt oxide electrodes

Understanding how lithium-ion batteries function down to the atomic level during charge and discharge cycling can provide valuable guidance to optimize structure-property relationships and to design and understand new electrode materials. Lithium insertion and reactions with the electrodes during charge and discharge cycling can occur via metastable structures with complex ordering and related non-equilibrium phenomena. Remarkably, these processes remain still poorly understood despite their significance in the operation of lithium battery systems in critical technologies. In this communication, we present the dynamics of lithium insertion into Co3O4 and the evolution of metastable phases as probed by in-situ transmission electron microscopy, in concert with first principles density functional theory calculations. We show that the initial lithium intercalation reaction occurs with the formation of several metastable and intermediate phases, followed by a sequence of conversion reactions that perturb and expand the cubic-close-packed oxygen array, ultimately generating an end-product of finely dispersed cobalt metal clusters within a Li2O matrix. The calculated non-equilibrium lithiation pathways corroborate with the experimental lithiation voltages, and explain the significant hysteresis that occurs during electrochemical cycling. The data provide new insights into the complexity of solid state lithium electrochemistry in metal oxides that are relevant to advancing lithium battery technology.

conversion reaction electrode↗