Search NASA⌕ Search

Engineering topics

Yaakobi, B

Publications and source records attributed to Yaakobi, B.

At least 19 records

Spherical shock-ignition experiments with the 40 + 20-beam configuration on OMEGA

Spherical shock-ignition experiments on OMEGA used a novel beam configuration that separates low-intensity compression beams and high-intensity spike beams. Significant improvements in the performance of plastic-shell, D 2 implosions were observed with repointed beams. The analysis of the coupling of the high-intensity spike beam energy into the imploding capsule indicates that absorbed hot-electron energy contributes to the coupling. The backscattering of laser energy was measured to reach up to 36% at single-beam intensities of ~ 8 x 10 15 W/cm/ 2 . Hard x-ray measurements revealed a relatively low hot-electron temperature of ~30 keV independent of intensity and timing. At the highest intensity, stimulated Brillouin scattering occurs near and above the quarter-critical density and the two-plasmon-decay instability is suppressed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental reduction of laser imprinting and Rayleigh–Taylor growth in spherically compressed, medium-Z-doped plastic targets

The effect of medium-Z doping of plastic ablators on laser imprinting and Rayleigh–Taylor (RT) instability growth was studied using spherical direct-drive implosions on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1977)]. The targets were spherical plastic (CH) shells, with an outer diameter of 860 μm and a thickness of 22 μm, volume doped with a varied concentration of Si (4.3% and 7.4%) and Ge (3.9%). The targets were imploded with 48 beams with a low-adiabat, triple-picket laser shape pulse with a peak intensity of 4×1014W/cm2, and a pulse duration of 2.5 ns. The shells were x-ray radiographed through a 40 -μm opening in the side of the target. The results show that volumetric impurity doping strongly reduces the shell density modulation and the instability growth rate. The amplitude of the initial imprint is reduced by a factor of 2.5 ±0.5 for CH[4.3% Si] targets and by a factor of 3 ±0.5 for CH[7.4% Si] and CH[3.9% Ge] targets. At the end of the acceleration phase, the reduction factor becomes 3 ±0.5 and 5 ± 0.5, correspondingly. The RT instability growth rate in doped targets is reduced by a factor of 1.5 compared to undoped ones. Simulations using the two-dimensional, radiation-hydrodynamics code draco show good agreement with the measurements

Fiksel, G.↗

Fast-electron generation in long-scale-length plasmas

Long-scale-length ({approx}400-{mu}m) planar CH plasmas have been generated on OMEGA EP with laser intensities of the order of 10{sup 14} W/cm{sup 2} and {approx}1-mm focal spots to quantify the number and temperature of fast electrons caused by the two-plasmon-decay instability. The main diagnostics were the time-integrated K{sub {alpha}} line emission and the hard x-ray bremsstrahlung (HXR) from a molybdenum (Mo) substrate. For the intensity range of 1-7 x 10{sup 14} W/cm{sup 2}, the Mo K{sub {alpha}} and HXR energies increased by more than three orders of magnitude. The fast-electron temperature in this range (deduced from the x-ray bremsstrahlung emission) rose from {approx}20 keV to {approx}90 keV. A Monte Carlo code was used to estimate the total energy (or number) of fast electrons based on these two experimental signatures. The resulting energy in fast electrons as a fraction of the laser energy was found to rise in the same intensity range up to {approx}1%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scaling hot-electron generation to long-pulse, high-intensity laser-solid interactions

Experiments have been performed to determine the effect of laser-pulse duration and energy on hot-electron-generation efficiency at high intensity. Thin copper foil targets were irradiated with 1 to 2100 J, 1 to 10 ps pulses focused to intensities >10{sup 18} W/cm{sup 2}. The target volume was varied from 75 x 75 x 3 {mu}m{sup 3} to 600 x 600 x 50 {mu}m{sup 3} to access a range of bulk thermal-electron temperatures up to several hundred electron volts. Comparison of K-photon spectroscopy measurements from these targets with electron transport and radiation-generation calculations indicates that the energy conversion efficiency into hot electrons is 20 {+-} 10%, independent of laser-pulse duration and energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Scaling Hot-Electron Generation to High-Power, Kilojoule-Class Laser-Solid Interactions

Thin-foil targets were irradiated with high-power (1 < P_L < 210 TW), 10-ps pulses focused to intensities of I > 10^18 W/cm^2 and studied with K-photon spectroscopy. Comparing the energy emitted in K photons to target-heating calculations shows a laser-energy-coupling efficiency to hot electrons of n_L-e = 20+/-10%. Time-resolved x-ray emission measurements suggest that laser energy is coupled to hot electrons over the entire duration of the incident laser drive. Comparison of the K-photon emission data to previous data at similar laser intensities shows that n_L-e is independent of laser-pulse duration from 1 < tau_p < 10 ps.

Nilson, P M↗

Scaling Hot-Electron Generation to High-Power, Kilojoule-Class Laser-Solid Interactions

Thin-foil targets were irradiated with high-power (1{<=}P{sub L}{<=}210 TW), 10-ps pulses focused to intensities of I>10{sup 18} W/cm{sup 2} and studied with K-photon spectroscopy. Comparing the energy emitted in K photons to target-heating calculations shows a laser-energy-coupling efficiency to hot electrons of {eta}{sub L-e}=20{+-}10%. Time-resolved x-ray emission measurements suggest that laser energy is coupled to hot electrons over the entire duration of the incident laser drive. Comparison of the K-photon emission data to previous data at similar laser intensities shows that {eta}{sub L-e} is independent of laser-pulse duration from 1{<=}{tau}{sub p}{<=}10 ps.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Spectroscopic modeling of an argon-doped shock-ignition implosion

We present results from the spectral postprocessing of a one-dimensional hydrodynamic simulation of an argon-doped, warm-shell shock-ignition implosion with a detailed atomic and radiation physics model. The argon tracer is added to the deuterium filling in the core for diagnostic purposes. Spectral features in the emergent intensity distribution in the photon energy range of the argon K-shell spectrum that have potential for diagnostic application are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Shock-tuned cryogenic-deuterium-tritium implosion performance on Omega

Cryogenic-deuterium-tritium (DT) target compression experiments with low-adiabat (alpha), multiple-shock drive pulses have been performed on the Omega Laser Facility [T. R. Boehly, D. L. Brown, R. S. Craxton et al., Opt. Commun. 133, 495 (1997)] to demonstrate hydrodynamic-equivalent ignition performance. The multiple-shock drive pulse facilitates experimental shock tuning using an established cone-in-shell target platform [T. R. Boehly, R. Betti, T. R. Boehly et al., Phys. Plasmas 16, 056301 (2009)]. These shock-tuned drive pulses have been used to implode cryogenic-DT targets with peak implosion velocities of 3x10{sup 7} cm/s at peak drive intensities of 8x10{sup 14} W/cm{sup 2}. During a recent series of alphaapprox2 implosions, one of the two necessary conditions for initiating a thermonuclear burn wave in a DT plasma was achieved: an areal density of approximately 300 mg/cm{sup 2} was inferred using the magnetic recoil spectrometer [J. A. Frenje, C. K. Li, F. H. Seguin et al., Phys. Plasmas 16, 042704 (2009)]. The other condition--a burn-averaged ion temperature <T{sub i}>{sub n} of 8-10 keV--cannot be achieved on Omega because of the limited laser energy; the kinetic energy of the imploding shell is insufficient to heat the plasma to these temperatures. A <T{sub i}>{sub n} of approximately 3.4 keV would be required to demonstrate ignition hydrodynamic equivalence [Betti et al., Phys. Plasmas17, 058102 (2010)]. The <T{sub i}>{sub n} reached during the recent series of alphaapprox2 implosions was approximately 2 keV, limited primarily by laser-drive and target nonuniformities. Work is underway to improve drive and target symmetry for future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion Experiments using Glass Ablators for Direct-Drive Inertial Confinement Fusion

Direct-drive implosions with 20-{mu}m-thick glass shells were conducted on the Omega Laser Facility to test the performance of high-Z glass ablators for direct-drive, inertial confinement fusion. The x-ray signal caused by hot electrons generated by two-plasmon-decay instability was reduced by more than {approx}40x and hot-electron temperature by {approx}2x in the glass compared to plastic ablators at ignition-relevant drive intensities of {approx}1x10{sup 15} W/cm{sup 2}, suggesting reduced target preheat. The measured absorption and compression were close to 1D predictions. The measured soft x-ray production in the spectral range of {approx}2 to 4 keV was {approx}2x to 3x lower than 1D predictions, indicating that the shell preheat caused by soft x-rays is less than predicted. A direct-drive-ignition design based on glass ablators is introduced.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct-Drive Inertial Fusion Research at the University of Rochester's Laboratory for Laser Energetics: A Review

This paper reviews the status of direct-drive inertial confinement fusion (ICF) research at the University of Rochester's Laboratory for Laser Energetics (LLE). LLE's goal is to demonstrate direct-drive ignition on the National Ignition Facility (NIF) by 2014. Baseline "all-DT" NIF direct-drive ignition target designs have been developed that have a predicted gain of 45 (1-D) at a NIF drive energy of ~1.6 MJ. Significantly higher gains are calculated for targets that include a DT-wicked foam ablator. This paper also reviews the results of both warm fuel and initial cryogenic-fuel spherical target implosion experiments carried out on the OMEGA UV laser. The results of these experiments and design calculations increase confidence that the NIF direct-drive ICF ignition goal will be achieved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Advanced-Ignition-Concept Exploration on OMEGA

Advanced ignition concepts, such as fast ignition and shock ignition, are being investigated at the Omega Laser Facility. Integrated fast-ignition experiments with room-temperature re-entrant cone targets have begun, using 18 kJ of 351 nm drive energy to implode empty 40μm thick CD shells, followed by 1.0 kJ of 1053 nm wavelength, short-pulse energy. Short pulses of 10 ps width have irradiated the inside of a hollow gold re-entrant cone at the time of peak compression. A threefold increase in the time-integrated, 2 to 7 keV x-ray emission was observed with x-ray pinhole cameras, indicating that energy is coupled from the short-pulse laser into the core by fast electrons. In shock-ignition experiments, spherical plastic-shell targets were compressed to high areal densities on a low adiabat, and a strong shock wave was sent into the converging, compressed capsule. In one experiment, 60 beams were used with an intensity spike at the end of the laser pulse, and the implosion performance was studied through neutron-yield and areal-density measurements. In a second experiment, the 60 OMEGA beams were split into a 40+20 configuration, with 40 low-intensity beams used for fuel assembly and 20 delayed beams with a short, high-intensity pulse shape (up to 1×1016 Wcm^-2) for shock generation.

Theobald, W↗

Advanced-Ignition-Concept Exploration on OMEGA

Advanced ignition concepts, such as fast ignition and shock ignition, are being investigated at the Omega Laser Facility. Integrated fast-ignition experiments with room-temperature re-entrant cone targets have begun, using 18 kJ of 351 nm drive energy to implode empty 40μm thick CD shells, followed by 1.0 kJ of 1053 nm wavelength, short-pulse energy. Short pulses of 10 ps width have irradiated the inside of a hollow gold re-entrant cone at the time of peak compression. A threefold increase in the time-integrated, 2 to 7 keV x-ray emission was observed with x-ray pinhole cameras, indicating that energy is coupled from the short-pulse laser into the core by fast electrons. In shock-ignition experiments, spherical plastic-shell targets were compressed to high areal densities on a low adiabat, and a strong shock wave was sent into the converging, compressed capsule. In one experiment, 60 beams were used with an intensity spike at the end of the laser pulse, and the implosion performance was studied through neutron-yield and areal-density measurements. In a second experiment, the 60 OMEGA beams were split into a 40+20 configuration, with 40 low-intensity beams used for fuel assembly and 20 delayed beams with a short, high-intensity pulse shape (up to 1×10 16 Wcm -2 ) for shock generation.

42 ENGINEERING↗

Study of Fast-Electron Transport in Laser-Illuminated Spherical Targets

The transport and scattering of fast electrons created by the two-plasmon-decay instability are studied by comparing the hard x-ray signal from two identically irradiated targets: a 1-mm-diam solid Cu sphere and a 1-mm-diam solid CH sphere, both coated with a 15 um layer of CH. Comparing the results with Monte Carlo code simulations shows the role of scattering in the higher-Z Cu target. We find evidence that the fast electrons are created with a wide angular divergence and that higher-energy electrons transmitted through the target are reflected back into the target. Because of scattering, the fast-electron energy deposition (preheat) in Cu is about half that in CH, namely, ~0.15% of the laser energy for Cu as compared with ~0.30% for CH. Embedded high-Z layers in imploding fusion targets, because of the scattering, could provide protection against preheat.

Yaakobi, B↗

Al 1s-2p Absorption Spectroscopy of Shock-Wave Heating and Compression in Laser-Driven Planar Foil

Time-resolved Al 1s-2p absorption spectroscopy is used to diagnose direct-drive, shock-wave heating and compression of planar targets having nearly Fermi-degenerate plasma conditions (Te ~ 10–40 eV, rho ~ 3–11 g/cm^3) on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. A planar plastic foil with a buried Al tracer layer was irradiated with peak intensities of 10^14–10^15 W/cm^2 and probed with the pseudocontinuum M-band emission from a point-source Sm backlighter in the range of 1.4–1.7 keV. The laser ablation process launches 10–70 Mbar shock waves into the CH/Al/CH target. The Al 1s-2p absorption spectra were analyzed using the atomic physic code PRISMSPECT to infer Te and rho in the Al layer, assuming uniform plasma conditions during shock-wave heating, and to determine when the heat front penetrated the Al layer. The drive foils were simulated with the one-dimensional hydrodynamics code LILAC using a flux-limited (f =0.06 and f =0.1) and nonlocal thermal-transport model [V. N. Goncharov et al., Phys. Plasmas 13, 012702 (2006)]. The predictions of simulated shock-wave heating and the timing of heat-front penetration are compared to the observations. The experimental results for a wide variety of laser-drive conditions and buried depths have shown that the LILAC predictions using f = 0.06 and the nonlocal model accurately model the shock-wave heating and timing of the heat-front penetration while the shock is transiting the target. The observed discrepancy between the measured and simulated shock-wave heating at late times of the drive can be explained by the reduced radiative heating due to lateral heat flow in the corona.

Sawada, H↗

Cryogneic-Target Performance and Implosion Physics Studies on OMEGA

Recent progress in direct-drive cryogenic implosions on the OMEGA Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reviewed. Ignition-relevant areal densities of ~200 mg/cm^2 in cryogenic D2 implosions with peak laser-drive intensities of ~5 x 10^14 W/cm^2 were previously reported [T. C. Sangster et al., Phys. Rev. Lett. 100, 185006 (2008)]. The laser intensity is increased to ~10^15 W/cm^2 to demonstrate ignition-relevant implosion velocities of 3–4 x 10^7 cm/ s, providing an understanding of the relevant target physics. Planar-target acceleration experiments show the importance of the nonlocal electron-thermal-transport effects for modeling the laser drive. Nonlocal and hot-electron preheat is observed to stabilize the Rayleigh–Taylor growth at a peak drive intensity of ~10^15 W/cm^2. The shell preheat caused by hot electrons generated by two-plasmon-decay instability was reduced by using Si-doped ablators. The measured compressibility of planar plastic targets driven with high-compression shaped pulses agrees well with one-dimensional simulations at these intensities. Shock mistiming has contributed to compression degradation of recent cryogenic implosions driven with continuous pulses. Multiple-picket (shock-wave) target designs make it possible for a more robust tuning of the shock-wave arrival times. Cryogenic implosions driven with double-picket pulses demonstrate somewhat improved compression performance at a peak drive intensity of ~10^15 W/cm^2.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fast-Ignition Target Design and Experimental-Concept Validation on OMEGA

A comprehensive scientific program is being pursued at LLE to explore the physics of fast ignition. The OMEGA EP Laser was completed in April 2008, adjacent to the 60 beam, 30 kJ OMEGA Laser Facility. OMEGA EP consists of four beamlines with a NIF-like architecture, each delivering up to 6.5 kJ of UV laser energy in long pulse (ns) mode into the OMEGA EP target chamber. Two of the beamlines can operate as high-energy petawatt lasers, with up to 2.6 kJ each with 10 ps pulse duration. These beams can either be injected into the OMEGA EP target chamber or combined collinearly into the existing OMEGA target chamber for integrated fast-ignitor experiments. Fuel-assembly experiments on OMEGA have achieved high fuel areal densities, and the effects of a cone on the fuel assembly are being studied. Experiments on short-pulse laser systems in collaboration with other institutions are being pursued to investigate the conversion efficiency from laser energy to fast electrons. A coherent transition radiation diagnostic to study the transport of the electrons in high-density material is being developed. Integrated experiments with room-temperature targets on OMEGA will be performed in 2008. Simulations of these integrated experiments show significant heating of up to 1 keV due to the hot electrons from the short-pulse laser.

Stoeckl, C↗