Search NASA⌕ Search

Engineering topics

Yablonovitch, Eli

Publications and source records attributed to Yablonovitch, Eli.

At least 19 records

Thermodynamics of Light Management in Near-Field Thermophotovoltaics

We evaluate near-field thermophotovoltaic (TPV) energy-conversion systems focusing in particular on their open-circuit voltage (V OC ). Unlike previous analyses based largely on numerical simulations with fluctuational electrodynamics, here, we develop an analytic model that captures the physics of near-field TPV systems and can predict their performance metrics. Using our model, we identify two opportunities of TPV systems operating in the near field. First, we show analytically that enhancement of radiative recombination is a natural consequence of operating in the near field. Second, we note that, owing to photon recycling and minimal radiation leakage in near-field operation, the PV cell used in near-field TPV systems can be much thinner compared to those used in solar PV systems. Since nonradiative recombination is a volumetric effect, use of a thinner cell reduces nonradiative losses per unit area. The combination of these two opportunities leads to increasingly large values of V OC as the TPV vacuum gap decreases. Hence, although operation in the near-field was previously perceived to be beneficial for electrical power-density enhancement, here, we emphasize that thin-film near-field TPVs are also significantly advantageous in terms of V OC and consequently conversion efficiency as well as power density. We provide numerical results for an InAs-based thin-film TPV that exhibits efficiency >50% at an emitter temperature as low as 1100 K.

42 ENGINEERING↗

Accurate calibration of thermophotovoltaic efficiency

Abstract The new record efficiency in Thermophotovoltaics relies upon a highly reflective rear mirror. The excellent rear mirror boosts voltage by enhancing the luminescence extraction, and separately also reflects low energy photons, which would otherwise be useless in thermophotovoltaics. The reflected low energy photons reheat the thermal emitter, and regenerate above-bandgap energy photons. The efficiency calibration for such regenerative thermophotovoltaics depends on several factors, yet predominantly on the accurate measurement of the rear mirror reflectivity. Here, we report on the technique for accurate measurement of mirror reflectivity, and of record thermophotovoltaic efficiency 29.1 ± 0.6%, at 1207 °C.

14 SOLAR ENERGY↗

Physics successfully implements Lagrange multiplier optimization

Optimization is a major part of human effort. While being mathematical, optimization is also built into physics. For example, physics has the Principle of Least Action; the Principle of Minimum Power Dissipation, also called Minimum Entropy Generation; and the Variational Principle. Physics also has Physical Annealing, which, of course, preceded computational Simulated Annealing. Physics has the Adiabatic Principle, which, in its quantum form, is called Quantum Annealing. Thus, physical machines can solve the mathematical problem of optimization, including constraints. Binary constraints can be built into the physical optimization. In that case, the machines are digital in the same sense that a flip–flop is digital. A wide variety of machines have had recent success at optimizing the Ising magnetic energy. We demonstrate in this paper that almost all those machines perform optimization according to the Principle of Minimum Power Dissipation as put forth by Onsager. Further, we show that this optimization is in fact equivalent to Lagrange multiplier optimization for constrained problems. We find that the physical gain coefficients that drive those systems actually play the role of the corresponding Lagrange multipliers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hybrid solar system

A hybrid solar system including a hybrid solar collector using non-imaging optics and photovoltaic components and a heat transfer and storage system in thermal communication with the hybrid solar collector, the heat transfer and storage system using particle laden gas as thermal media to simultaneously generate and store electricity and high temperature dispatchable heat.

14 SOLAR ENERGY↗

Tunnel-FET Switching Is Governed by Non-Lorentzian Spectral Line Shape

In tunnel field-effect transistors (tFETs), the preferred mechanism for switching occurs by alignment (on) or misalignment (off) of two energy levels or band edges. Unfortunately, energy levels are never perfectly sharp. When a quantum dot interacts with a wire, its energy is broadened. Its actual spectral shape controls the current/voltage response of such transistor switches, from on (aligned) to off (misaligned). The most common model of spectral line shape is the Lorentzian, which falls off as reciprocal energy offset squared. Unfortunately, this is too slow a turnoff, algebraically, to be useful as a transistor switch. Electronic switches generally demand an on/off ratio of at least a million. Steep exponentially falling spectral tails would be needed for rapid off-state switching. This requires a new electronic feature, not previously recognized: narrowband, heavy-effective mass, quantum wire electrical contacts, to the tunneling quantum states. These are a necessity for spectrally sharp switching.

42 ENGINEERING↗

Electrical suppression of all nonradiative recombination pathways in monolayer semiconductors

Defects in conventional semiconductors substantially lower the photoluminescence (PL) quantum yield (QY), a key metric of optoelectronic performance that directly dictates the maximum device efficiency. Here, two-dimensional transition-metal dichalcogenides (TMDCs), such as monolayer MoS 2 , often exhibit low PL QY for as-processed samples, which has typically been attributed to a large native defect density. We show that the PL QY of as-processed MoS 2 and WS 2 monolayers reaches near-unity when they are made intrinsic through electrostatic doping, without any chemical passivation. Surprisingly, neutral exciton recombination is entirely radiative even in the presence of a high native defect density. This finding enables TMDC monolayers for optoelectronic device applications as the stringent requirement of low defect density is eased.

36 MATERIALS SCIENCE↗

Light Material Interactions in Energy Conversion (Final Report)

The scientific vision of the “Light-Material Interactions in Energy Conversion” Energy Frontier Research Center (LMI-EFRC) is embodied in our mission statement: ‘to tailor the morphology, complex dielectric structure, and electronic properties of matter so as to sculpt the flow of sunlight and heat, enabling light conversion to electrical energy with unprecedented efficiency’. Founded in 2009, the LMI-EFRC has become a national resource for fundamental optical principles and phenomena relevant to solar energy conversion, addressing new scientific opportunities that enable efficient utilization of the entire visible and infrared solar resource. The LMI-EFRC is directed by Prof. Ralph Nuzzo and centered at its lead institution, the California Institute of Technology. The Center is an integrated and collaborative partnership of research leaders in photonics and photonic materials, comprising 14 faculty investigators that span six academic departments at five institutions, including Profs. Harry Atwater, Andrei Faraon, Nathan Lewis, and Austin Minnich at Caltech; Profs. Ralph Nuzzo, Paul Braun and John Rogers at the University of Illinois at Urbana-Champaign; Prof. Jennifer Lewis at Harvard University; Profs. Mark Brongersma, Jennifer Dionne, and Shanhui Fan at Stanford University; and Profs. Paul Alivisatos, Eli Yablonovitch, and Xiang Zhang at Lawrence Berkeley National Laboratory. The Center is organized into four research groups (RGs) that address scientific themes related to light-matter interactions, with each team spanning multiple institutional partners and designed to meet our scientific objectives. Notable project outcomes that address the LMI Mission and 2014-2018 goals include: (1) RG1 “New Light Management Mechanisms” demonstrated tunable and active nanostructured patterned surfaces (‘metasurfaces’) for control of light absorption, reflection, and propagation. (2) RG2 “Solar Spectrum Control and Conversion” developed colloidal nanocrystals with designer optical properties for fundamental studies of solar spectrum control and conversion. (3) RG3 “Thermal Photon Harvesting” established photonic design principles to harness and control thermal photons in novel conversion systems. (4) RG4 “Programmable Assembly of Photonic and Electronic Architectures” developed powerful new methods for light- and matter-based additive fabrication of electronic and photonic architectures.

14 SOLAR ENERGY↗

Pushing the Limits of Thermophotovoltaic Efficiency

We report power conversion efficiency of ~28% from a thermophotovoltaic device, employing the concept of photon regeneration. The regeneration is accomplished using photovoltaic band-edge as the spectral filter. This high efficiency is a direct consequence of enhanced sub-bandgap reflectivity of the device used. Our detail theoretical analysis shows that with further improvement in device geometry and material, it would be possible to achieve near 45% power conversion efficiency.

14 SOLAR ENERGY↗

Leveraging continuous material averaging for inverse electromagnetic design

Inverse electromagnetic design has emerged as a way of efficiently designing active and passive electromagnetic devices. This maturing strategy involves optimizing the shape or topology of a device in order to improve a figure of merit-a process which typically requires that we compute the gradient of a figure of merit which describes device performance, potentially with respect to many design variables. In this paper, we introduce a new strategy based on smoothing abrupt material interfaces which enables us to efficiently compute these gradients with high accuracy irrespective of the resolution of the underlying simulation. This has advantages over previous approaches to shape and topology optimization in nanophotonics which are either prone to gradient errors or place important constraints on the shape of the device. As a demonstration of this new strategy, we optimize a non-adiabatic waveguide taper between a narrow and wide waveguide. Finally, this optimization leads to a non-intuitive design with a very low insertion loss of only 0.041 dB at 1550 nm.

36 MATERIALS SCIENCE↗

Ultrafast Spontaneous Emission from a Slot-Antenna Coupled WSe 2 Monolayer

Optical antennas can enhance the spontaneous emission rate from nanoemitters by orders of magnitude, enabling the possibility of an ultrafast, efficient, nanoscale LED. Semiconductors would be the preferred material for such a device to allow for direct high-speed modulation. However, efficient nanoscale devices are challenging to implement because of high surface recombination typical of most III-V materials. Monolayer transition metal dichalcogenides are an attractive alternative to a III-V emitter due to their intrinsically nanoscale dimensions, direct bandgap, and near-ideal surfaces resulting in high intrinsic quantum yield. In this work, we couple a nanostrip (30 nm × 250 nm) monolayer of WSe 2 to a cavity-backed optical slot antenna through a self-aligned fabrication process. Photoluminescence, scattering, and lifetime measurements are used to estimate a radiative spontaneous emission rate enhancement of 318× from WSe 2 monolayers coupled to on-resonance antennas. Finally, such a huge increase in the spontaneous emission rate results in an ultrafast radiative recombination rate and a quantum yield in nanopatterned monolayers comparable to unprocessed exfoliated flakes of WSe 2 .

2D materials↗

Experimental Demonstration of 28.2% Thermophotovoltaic Conversion Efficiency

Efficient luminescence extraction enables us to use the photovoltaic band gap as the spectral filter for thermophotovoltaics. Using this concept, we demonstrate a 28.2% conversion efficiency, higher than the previously reported value for the range of the emitter temperature (700 degrees C-1250 degrees C) used.

14 SOLAR ENERGY↗

Electroluminescent refrigeration by ultra-efficient GaAs light-emitting diodes

Electroluminescence—the conversion of electrons to photons in a light-emitting diode (LED)—can be used as a mechanism for refrigeration, provided that the LED has an exceptionally high quantum efficiency. We investigate the practical limits of present optoelectronic technology for cooling applications by optimizing a GaAs/GaInP double heterostructure LED. We develop a model of the design based on the physics of detailed balance and the methods of statistical ray optics, and predict an external luminescence efficiency of η ext = 97.7% at 263 K. To enhance the cooling coefficient of performance, we pair the refrigerated LED with a photovoltaic cell, which partially recovers the emitted optical energy as electricity. For applications near room temperature and moderate power densities (1.0–10 mW/cm 2 ), we project that an electroluminescent refrigerator can operate with up to 1.7× the coefficient of performance of thermoelectric coolers with ZT = 1, using the material quality in existing GaAs devices. We also predict superior cooling efficiency for cryogenic applications relative to both thermoelectric and laser cooling. Large improvements to these results are possible with optoelectronic devices that asymptotically approach unity luminescence efficiency.

36 MATERIALS SCIENCE↗

High-performance near-field electroluminescent refrigeration device consisting of a GaAs light emitting diode and a Si photovoltaic cell

We consider a near-field electroluminescent refrigeration device. The device uses a GaAs light emitting diode as the cold side, and a Si photovoltaic cell as the hot side. The two sides are brought in close proximity to each other across a vacuum gap. The cooling is achieved by applying a positive bias on the GaAs light emitting diode. We show that the choice of GaAs and Si here can suppress the non-idealities for electroluminescent cooling purposes: GaAs has a wide bandgap with low Auger recombination, and Si is a non-polar semiconductor which leads to significantly reduced sub-bandgap heat transfer. We show that by using this configuration in the near-field regime, the cooling power density can reach 10 5 W/m 2 even in the presence of realistic Auger recombination and Shockley-Read-Hall recombination. In addition, with photovoltaic power recovery from the Si cell, the efficiency of the device can be further improved. Our work points to the significant potential of combining near-field heat transfer with active semiconductor devices for the control of heat flow.

14 SOLAR ENERGY↗

Short-channel field-effect transistors with 9-atom and 13-atom wide graphene nanoribbons

Bottom-up synthesized graphene nanoribbons and graphene nanoribbon heterostructures have promising electronic properties for high-performance field-effect transistors and ultra-low power devices such as tunneling field-effect transistors. However, the short length and wide band gap of these graphene nanoribbons have prevented the fabrication of devices with the desired performance and switching behavior. Here, by fabricating short channel (L ch ~ 20 nm) devices with a thin, high-κ gate dielectric and a 9-atom wide (0.95 nm) armchair graphene nanoribbon as the channel material, we demonstrate field-effect transistors with high on-current (I on > 1 μA at V d = -1 V) and high I on /I off ~ 10 5 at room temperature. We find that the performance of these devices is limited by tunneling through the Schottky barrier at the contacts and we observe an increase in the transparency of the barrier by increasing the gate field near the contacts. Our results thus demonstrate successful fabrication of high-performance short-channel field-effect transistors with bottom-up synthesized armchair graphene nanoribbons.

36 MATERIALS SCIENCE↗