Engineering topics

Yamauchi, Gloria K.

Publications and source records attributed to Yamauchi, Gloria K..

33 records · Page 2

NASA NTRS1999

Overview of the Testing of a Small-Scale Proprotor

This paper presents an overview of results from the wind tunnel test of a 1/4-scale V-22 proprotor in the Duits-Nederlandse Windtunnel (DNW) in The Netherlands. The small-scale proprotor was tested on the isolated rotor configuration of the Tilt Rotor Aeroacoustic Model (TRAM). The test was conducted by a joint team from NASA Ames, NASA Langley, U.S. Army Aeroflightdynamics Directorate, and The Boeing Company. The objective of the test was to acquire a benchmark database for validating aeroacoustic analyses. Representative examples of airloads, acoustics, structural loads, and performance data are provided and discussed.

Young, Larry A.↗

NASA NTRS1999

Overview of the Testing of a Small-Scale Proprotor

Young, Larry A.↗

NASA NTRS1998

Technology Investigations With the Tilt Rotor Aeroacoustic Model (TRAM)

This paper introduces the Tilt Rotor Aeroacoustic Model (TRAM) project. The TRAM project is a key infrastructure investment for NASA tiltrotor research. The TRAM project consists of the development and testing of two modular, hardware-compatible, test stands: an isolated rotor configuration and a fullspan model (dual rotors with a complete airframe representation). These two test stands are inclusively called the Tilt Rotor Aeroacoustic Model (TRAM). The baseline proprotors and airframe of the TRAM test stands are nominally 1/4-scale representative of the V-22 Osprey aircraft. The research objectives of the project, the TRAM hardware design features and capabilities, illustrative examples of the type and quality of data that can be acquired with the TRAM, and the current status of the overall project will be discussed in this paper.

Young, Larry A.↗

NASA NTRS1994

Measurements of atmospheric turbulence effects on tail rotor acoustics

Results from an outdoor hover test of a full-scale Lynx tail rotor are presented. The investigation was designed to further the understanding of the acoustics of an isolated tail rotor hovering out-of-ground effect in atmospheric turbulence, without the effects of the main rotor wake or other helicopter components. Measurements include simultaneous rotor performance, noise, inflow, and far-field atmospheric turbulence. Results with grid-generated inflow turbulence are also presented. The effects of atmospheric turbulence ingestion on rotor noise are quantified. In contradiction to current theories, increasing rotor inflow and rotor thrust were found to increase turbulence ingestion noise. This is the final report of Task 13A--Helicopter Tail Rotor Noise, of the NASA/United Kingdom Defense Research Agency cooperative Aeronautics Research Program.

Hagen, Martin J.↗

NASA NTRS1994

Navier-Stokes Calculations for a Highly-Twisted Rotor Near Stall

The viscous flow field near the surface of a hovering rotor blade was studied for blade twist distributions typical of a till rotor blade and a conventional helicopter rotor blade. Three blade geometries were studied, including a tilt rotor blade twist distribution (baseline), conventional helicopter rotor blade twist distribution, and the baseline twist distribution with 2 deg of precone. The results give insight into the delayed stall phenomenon often observed for highly twisted rotors. Calculations were performed for a high thrust condition near stall using the thin-layer Navier-Stokes CFD code TURNS. Effects of built-in twist on section force coefficients, skin friction, velocities, surface pressures, and boundary layer shape factor are discussed. Although the rotor thrust coefficient was nominally the same for the cases using the two twist distributions, large differences were found in the section in-plane and normal force coefficients. These preliminary results imply that the blade outboard region, rather than the inboard region, provides the majority of the performance advantage of the baseline case over the low twist case. Skin friction, velocities near the blade, and surface pressures for the two twist distributions reveal significant differences in the blade outboard region.

Yamauchi, Gloria K.↗

NASA NTRS1992

Effects of ingested atmospheric turbulence on measured tail rotor acoustics

Results from an outdoor hover test of a full-scale Lynx tail rotor are presented. The investigation was designed to further the understanding of the acoustics of an isolated tail rotor hovering out-of-ground effect in atmospheric turbulence, without the effects of the main rotor wake or other helicopter components. Measurements include simultaneous rotor performance, noise, inflow, and far-field atmospheric turbulence. Results with grid-generated inflow turbulence are also presented. The effects of turbulence ingestion on rotor noise are quantified. Turbulence ingestion noise is found to be the dominant noise mechanism at locations near the rotor axis. At these locations, the sound radiated by the hovering rotor increases with both increasing atmospheric wind speed and ingested rms turbulent velocity.

Signor, David B.↗

NASA NTRS1991

Full-scale investigation of aerodynamic interactions between a rotor and fuselage

A wind tunnel program has been conducted in the NASA Ames National Full-Scale Aerodynamics Complex to investigate the aerodynamic interactions between a full-scale helicopter main rotor and simple fuselage. This program provides the first complete, quantitative data base detailing the effects of a rotor on a full-scale fuselage. Steady fuselage and rotor loads were obtained as well as steady and unsteady fuselage pressures. Data were acquired over a range of rotor thrusts, advance ratios, and shaft tilts. As expected, results indicate that the largest effects on mean fuselage forces, moments, and surface pressures occur at low speeds and high rotor thrusts. Quantitative comparisons were made to determine the ability of small-scale tests to simulate the effect of the rotor on mean fuselage forces and pressures.

Norman, Thomas R.↗

NASA NTRS1990

Hub loads analysis of the SA349/2 helicopter

The forces and moments at the rotor hub of an Aerospatiale SA349/2 helicopter were investigated. The study included three main topics. First, measured hub forces and moments for a range of level flight conditions (mu = 0.14 to 0.37) were compared with predictions from a comprehensive rotorcraft analysis to examine the influence of the wake model on the correlations. Second, the effect of changing the blade mass distribution and blade chordwise center of gravity location on the 3/rev nonrotating frame hub loads was studied for a high-speed flight condition (mu = 0.37). Third, the use of higher harmonic control to reduce nonrotating frame 3/rev hub shear forces was investigated. The last two topics were theoretical studies only.

Heffernan, Ruth M.↗

NASA NTRS1989

Performance and loads data from an outdoor hover test of a Lynx tail rotor

A Lynx tail rotor was tested in hover at the Outdoor Aerodynamic Research Facility at NASA Ames Research Center. The test objectives were to measure the isolated rotor performance to provide a baseline for subsequent testing, and to operate the rotor throughout the speed and collective envelope before testing in the NFAC 40- by 80-Foot Wind Tunnel. Rotor forces and blade bending moments were measured at ambient wind conditions from zero to 6.23 m/sec. The test envelope was limited to rotor speeds of 1550 to 1850 rpm and minus 13 deg to plus 20 deg of blade collective pitch. The isolated rotor performance and blade loads data are presented.

Signor, David B.↗

NASA NTRS1988

Hub and blade structural loads measurements of an SA349/2 helicopter

Data from 23 flight conditions, including level flights ranging from advance ratio mu = 0.14 to 0.37 and steady turning flights from advance ratio mu = 0.26 to 0.35, are presented for an Aerospatiale SA349/2 Gazelle helicopter. The data include hub loads data (for 6 of the 23 conditions), blade structural data at eleven different blade radial stations, and fuselage structural data. All dynamic data are presented as harmonic analysis coefficients (ten harmonics per rotor revolution). The data acquisition and reduction procedures are also documented. Blade structural and inertial properties are provided in addition to control system geometry and properties.

Yamauchi, Gloria K.↗

NASA NTRS1988

Correlation of SA349/2 Helicopter Flight Test Data with a Comprehensive Rotorcraft Model

A comprehensive rotorcraft analysis model, CAMRAD, was used to predict blade aerodynamic and structural loads and performance for comparison with flight test data. The data were obtained from an SA349/2 helicopter with an advanced geometry rotor. Sensitivity of the correlation to wake geometry, blade dynamics, and blade aerodynamic effects was investigated. Blade chordwise pressure coefficients were predicted for the transonic regimes near the blade tip using the model coupled with two finite-difference codes.

Yamauchi, Gloria K.↗

NASA NTRS1987

Time-averaged aerodynamic loads on the vane sets of the 40- by 80-foot and 80- by 120-foot wind tunnel complex

Time-averaged aerodynamic loads are estimated for each of the vane sets in the National Full-Scale Aerodynamic Complex (NFAC). The methods used to compute global and local loads are presented. Experimental inputs used to calculate these loads are based primarily on data obtained from tests conducted in the NFAC 1/10-Scale Vane-Set Test Facility and from tests conducted in the NFAC 1/50-Scale Facility. For those vane sets located directly downstream of either the 40- by 80-ft test section or the 80- by 120-ft test section, aerodynamic loads caused by the impingement of model-generated wake vortices and model-generated jet and propeller wakes are also estimated.

Aoyagi, Kiyoshi↗

NASA NTRS1987

Correlation of SA349/2 helicopter flight-test data with a comprehensive rotorcraft model

A comprehensive rotorcraft analysis model was used to predict blade aerodynamic and structural loads for comparison with flight test data. The data were obtained from an SA349/2 helicopter with an advanced geometry rotor. Sensitivity of the correlation to wake geometry, blade dynamics, and blade aerodynamic effects was investigated. Blade chordwise pressure coefficients were predicted for the blade transonic regimes using the model coupled with two finite-difference codes.

Yamauchi, Gloria K.↗

NASA NTRS1987

Prediction of SA 349/2 GV blade loads in high speed flight using several rotor analyses

The influence of blade dynamics, dynamic stall, and transonic aerodynamics on the predictions of rotor loads in high-speed flight are presented. Data were obtained from an Aerospatiale Gazelle SA 349/2 helicopter with three Grande Vitesse blades. Several analyses are used for this investigation. First, blade dynamics effects on the correlation are studied using three rotor analyses which differ mainly in the method of calculating the blade elastic response. Next, an ONERA dynamic stall model is used to predict retreating blade stall. Finally, advancing blade aerodynamic loads are calculated using a NASA-developed rotorcraft analysis coupled with two transonic finite-difference analyses.

Gaubert, Michel↗

NASA NTRS1986

Correlation of SA349/2 helicopter flight-test data with a comprehensive rotorcraft model

Yamauchi, Gloria K.↗