Search NASA⌕ Search

Engineering topics

Yan, Baojie

Publications and source records attributed to Yan, Baojie.

Ultrathin silicon oxide prepared by in-line plasma-assisted N 2 O oxidation (PANO) and the application for n-type polysilicon passivated contact

We develop a plasma-assisted nitrous-oxide (N 2 O) gas oxidation (PANO) method to prepare the ultrathin silicon oxide (SiO x ) for polysilicon (poly-Si) passivated contact. The effects of preparation conditions, including the substrate temperature, processing time, and plasma power, are studied. Afterwards, we integrate the PANO SiO x into the polysilicon passivated contact and optimize the passivation and contact performances. Excellent surface passivation with the n-type poly-Si and PANO SiO x on the n-type c-Si wafer is achieved by 880 °C annealing, which shows competitive passivation quality to the one with NASO SiO x . Champion implied open-circuit voltage (iV oc ) and single-sided recombination saturated current (J 0 ) reach 730 mV and 4.3 fA/cm 2 after crystallization; and they are further improved to 747 mV and 2.0 fA/cm 2 (3 × 10 15 cm -3 ) after subsequent AlO x /SiN x hydrogenation. Using transmission electron microscopy (TEM), we find that the thickness of PANO SiO x ranges 1.1–2.4 nm and the controlled nitric acid oxidized SiO x (NAOS) ranges 1.3–1.8 nm. The contact resistivity (ρ c ) is typically <10 mΩ cm 2 with the annealing temperature of >820 °C. Also, the crystallinity, phosphorous in-diffusion profile, and current-leaking density of the passivated contacts are investigated. In general, the PANO SiO x and in-situ doping amorphous silicon precursor can be fabricated in one PECVD system without additional equipment or transfer procedures, which is favorable for the high-efficiency, low-cost industrial manufacture.

14 SOLAR ENERGY↗

Carrier transport through the ultrathin silicon-oxide layer in tunnel oxide passivated contact (TOPCon) c-Si solar cells

The carrier transport through the silicon-oxide (SiO x ) layer in tunnel oxide passivated contact (TOPCon) c-Si solar cells has been studied experimentally and by simulation. The current intensity versus voltage (J-V) characteristics of GaIn/n-c-Si/SiO x /n + -poly-Si/Al structures shows a linear Ohmic characteristic, while a non-Ohmic behavior is observed in the samples without the n + -poly-Si contact layer. Conductive Atomic Force Microscopy (c-AFM) images reveal some current spikes on the surface of the samples, which could be related to the transport through pinholes. The simulation results show that 1) a rectification characteristic is obtained when only the tunneling mechanism is included, 2) both the reverse saturation current and the forward current increase when a small amount of transport through pinholes is introduced, and 3) finally a linear Ohmic behavior is observed when the pinhole transport component reaches a certain level. Furthermore, the simulation for whole TOPCon solar cells provides some useful results. For very thin SiO x (< 1.2 nm), the tunneling provides sufficient high tunneling probability and high efficiency TOPCon solar cells can be obtained without transport through pinholes if the passivation is ensured; while for a relatively thick SiO x (> 1.2 nm) without the transport through pinholes, the TOPCon solar cell shows a poor fill factor (FF) with a high series resistance (Rs) because the tunneling does not provide a sufficient high transport channel for carrier transport, and the introduction of a small number of transports through pinholes improves the FF and reduces the Rs, hence improves the PCE. However, a high possibility for carrier going through pinholes reduces all of the performance parameters and degrades PCE for all the cases simulated. Therefore, an optimized pinhole density and size distribution is critical engineering for solar cell performance optimization. However, the establishment of an optimized method to precisely control the pinhole formation and characterization is still on the way.

14 SOLAR ENERGY↗

Microscopic Measurements of Electrical Potential in Hydrogenated Nanocrystalline Silicon Solar Cells: Preprint

We report on a direct measurement of electrical potential and field profiles across the n-i-p junction of hydrogenated nanocrystalline silicon (nc-Si:H) solar cells, using the nanometer-resolution potential imaging technique of scanning Kelvin probe force microscopy (SKPFM). It was observed that the electric field is nonuniform across the i layer. It is much higher in the p/i region than in themiddle and the n/i region, illustrating that the i layer is actually slightly n-type. A measurement on a nc-Si:H cell with a higher oxygen impurity concentration shows that the nonuniformity of the electric field is much more pronounced than in samples having a lower O impurity, indicating that O is an electron donor in nc-Si:H materials. This nonuniform distribution of electric field implies amixture of diffusion and drift of carrier transport in the nc-Si:H solar cells. The composition and structure of these nc-Si:H cells were further investigated by using secondary-ion mass spectrometry and Raman spectroscopy, respectively. The effects of impurity and structural properties on the electrical potential distribution and solar cell performance are discussed.

14 SOLAR ENERGY↗

Method for depositing high-quality microcrystalline semiconductor materials

A process for the plasma deposition of a layer of a microcrystalline semiconductor material is carried out by energizing a process gas which includes a precursor of the semiconductor material and a diluent with electromagnetic energy so as to create a plasma therefrom. The plasma deposits a layer of the microcrystalline semiconductor material onto the substrate. The concentration of the diluent in the process gas is varied as a function of the thickness of the layer of microcrystalline semiconductor material which has been deposited. Also disclosed is the use of the process for the preparation of an N-I-P type photovoltaic device.

36 MATERIALS SCIENCE↗