Engineering topics
Publications and source records attributed to Yan, Jinyuan.
Non-hydrostatic high pressure X-ray diffraction is used to study the hardness of superhard ReB 2 nanocrystals. All nanocrystals show less plastic deformation under load than bulk ReB 2 , with the smallest nanocrystals showing the most enhancement.
Abstract The thermal equation of state (TEOS) for solids is a mathematic model among pressure, temperature and density, and is essential for geophysical, geochemical, and other high pressure–temperature (high P–T) researches. However, in the last few decades, there has been a growing concern about the accuracy of the pressure scales of the calibrants, and efforts have been made to improve it by either introducing a reference standard or building new thermal pressure models. The existing thermal equation of state, P ( V , T ) = P ( V , T 0 ) + P th ( V , T ), consists of an isothermal compression and an isochoric heating, while the thermal pressure is the pressure change in the isochoric heating. In this paper, we demonstrate that, for solids in a soft pressure medium in a diamond anvil cell, the thermal pressure can neither be determined from a single heating process, nor from the thermal pressure of its calibrant. To avoid the thermal pressure, we propose to replace the thermal pressure with a well-known thermal expansion model, and integrate it with the isothermal compression model to yields a Birch–Murnaghan-expansion TEOS model, called VPT TEOS. The predicted pressure of MgO and Au at ambient pressure from Birch–Murnaghan-expansion VPT TEOS model matches the experimental pressure of zero (0) GPa very well, while the pressure prediction from the approximated Anderson PVT TEOS exhibit a big deviation and a wrong trend.
In situ x-ray diffraction measurements and inverse Monte Carlo simulations of pair distribution functions were used to study the structural response of PbO 2 under pressure and to characterize the local structure of liquid PbO 2 . Two phase transitions are observed upon room-temperature compression of crystalline PbO 2 up to ~65 GPa. Here, the starting mixture of rutile structured β– PbO 2 and orthorhombic α– PbO 2 undergoes a transition to a ZrO 2 -type orthorhombic phase with space group Pbca at ~21 GPa. Above 42 GPa, the Pbca phase transforms to a cotunnite-type phase with space group Pnam. In this paper, we also report short-range order in liquid PbO 2 , showing ~8–9-fold and 4–5-fold coordination around Pb and O atoms, respectively.
A thermal expansion coefficient (αp) is an essential thermophysical quantity for high-pressure research. The thermal expansion coefficient is the volume change over the temperature in an isobaric heating process. Although isobaric heating processes for diamond anvil cell (DAC) have been conducted by keeping the pressure constant during heating, pressure determination at high-temperature high pressure is debatable for decades long. In this paper, a revertible heating/cooling approach is presented, while its pressure determination at high-temperature high pressure is not required. We report a pressure-dependent thermal expansion coefficient of MgO at 9.5 GPa by reversible heating/cooling was determined by a DAC and its result matches the one collected by a large volume press, whose isobaric heating was conducted by manually adjusting its load/pressure.
In this work, the performance of the carbon doped compositionally complex alloy (CCA) MoNbTaW was studied under ambient and high pressure and high temperature conditions. TaC and NbC carbides were formed when a large concentration of carbon was introduced while synthesizing the MoNbTaW alloy. Both FCC carbides and BCC CCA phases were detected in the sample compound at room temperature, in which the BCC phase was believed to have only refractory elements MoNbTaW while FCC carbide came from TaC and NbC. Carbides in the carbon doped MoNbTaW alloy were very stable since no phase transition was obtained even under 3.1 GPa and 870 °C by employing the resistor-heating diamond anvil cell (DAC) synchrotron X-ray diffraction technique. Via in situ examination, this study confirms the stability of carbides and MoNbTaW in the carbon doped CCA even under high pressure and high temperature.
The hydrogen-absorbing ability of a mantle mineral in its structure determines the capacity of the water reservoirs hosted by the mineral. Water reservoirs at the base of Earth’s mantle directly influence the fate of water brought down by slab subduction and the seismic heterogeneity such as ultralow-velocity zones (ULVZs) at the core-mantle boundary. Pyrite-FeO 2 H x (0 ≤ x ≤ 1) presents a possibility of such reservoirs in the deep mantle. Ever since the discovery of this mineral phase, however, its chemistry at the lower mantle conditions has been debated. We conducted kinetics experiments of pyrite-FeO 2 H x dehydrogenation at 110 GPa/2100 K, 110 GPa/2300 K, and 120 GPa/2300 K and P-V-T equation of state analysis using in situ synchrotron X-ray diffraction. We found that x approaches 0.80, 0.75, and 0.79, respectively, at the above conditions. The collective P-V-T data yield K 0 = 241(13) GPa, K' = 4.2(4), dK/dT = –0.028(1) GPa/K, α 0 = 4.32(13) × 10 –5 K –1 , and α 1 = 0.31(10) × 10 –8 K –2 for the composition of x = 0.75 ± 0.04. Our first-principles calculations indicate that FeO 2 H 0.75 with a slightly distorted pyrite structure is stable at 100 GPa. These results indicate that this mineral is likely present in the deep mantle with rather a partially dehydrogenated composition than FeO 2 or FeOOH. Furthermore, the results also clarify the difference between the ULVZs originated from pyrite-FeO 2 H x and those from partial melting in terms of shear and compressional wave seismic velocity reduction ratio δlnV S /δlnV P .
The excellent mechanical properties of high-entropy alloys (HEAs) make them promising materials for advances in science and technology. However, the underlying mechanism of plastic deformation is not well understood. In situ experiments are urgently required to provide a fundamental understanding of the plastic deformation under high pressure. We performed in situ synchrotron X-ray diffraction (XRD) experiments to study compression deformation behavior of the HEA MoNbTaVW in a radial diamond anvil cell (rDAC). Our results show that the strength and ratio of the stress-to-shear modulus values are ~1.5 and 3 times that of pure tungsten (W), respectively. MoNbTaVW showed plastic deformation above 5 GPa and displayed a much stronger texture. In this work, we found that the active dislocation behavior is mainly responsible for the high strength in MoNbTaVW under compression. This unique technique opens a new avenue to investigate the in situ mechanical properties and their mechanism in other types of HEAs.
In this work, the formation of carbide with the concertation of carbon at 0.1 at.% in refractory high-entropy alloy (RHEA) Mo 15 Nb 20 Re 15 Ta 30 W 20 was studied under both ambient and high-pressure high-temperature conditions. The x-ray diffraction of dilute carbon (C)-doped RHEA under ambient pressure showed that the phases and lattice constant of RHEA were not influenced by the addition of 0.1 at.% C. In contrast, C-doped RHEA showed unexpected phase formation and transformation under combined high-pressure and high-temperature conditions by resistively employing the heated diamond anvil cell (DAC) technique. The new FCC_L1 2 phase appeared at 6 GPa and 809 °C and preserved the ambient temperature and pressure. High-pressure and high-temperature promoted the formation of carbides Ta 3 C and Nb 3 C, which are stable and may further improve the mechanical performance of the dilute C-doped alloy Mo 15 Nb 20 Re 15 Ta 30 W 20 .
The Hall–Petch relationship, according to which the strength of a metal increases as the grain size decreases, has been reported to break down at a critical grain size of around 10 to 15 nanometres. As the grain size decreases beyond this point, the dominant mechanism of deformation switches from a dislocation-mediated process to grain boundary sliding, leading to material softening. In one previous approach, stabilization of grain boundaries through relaxation and molybdenum segregation was used to prevent this softening effect in nickel–molybdenum alloys with grain sizes below 10 nanometres. Here we track in situ the yield stress and deformation texturing of pure nickel samples of various average grain sizes using a diamond anvil cell coupled with radial X-ray diffraction. Our high-pressure experiments reveal continuous strengthening in samples with grain sizes from 200 nanometres down to 3 nanometres, with the strengthening enhanced (rather than reduced) at grain sizes smaller than 20 nanometres. Here, we achieve a yield strength of approximately 4.2 gigapascals in our 3-nanometre-grain-size samples, ten times stronger than that of a commercial nickel material. A maximum flow stress of 10.2 gigapascals is obtained in nickel of grain size 3 nanometres for the pressure range studied here. We see similar patterns of compression strengthening in gold and palladium samples down to the smallest grain sizes. Simulations and transmission electron microscopy reveal that the high strength observed in nickel of grain size 3 nanometres is caused by the superposition of strengthening mechanisms: both partial and full dislocation hardening plus suppression of grain boundary plasticity. These insights contribute the ongoing search for ultrastrong metals via materials engineering.