Engineering topics

Yang, Ankun

Publications and source records attributed to Yang, Ankun.

8 records

DOE OSTI2023

High-Quality Surface Plasmon Polaritons in Large-Area Sodium Nanostructures

Sodium (Na) is predicted to be an ideal plasmonic material with ultralow optical loss across visible to near-infrared (NIR). However, there has been limited research on Na plasmonics. We develop a scalable fabrication method for Na nanostructures by combining phase-shift photolithography and a thermo-assisted spin-coating process. Using this method, we fabricated Na nanopit arrays with varying periodicities (300-600 nm) and with tunable surface plasmon polariton (SPP) modes spanning visible to NIR. We achieved SPP resonances as narrow as 9.3 nm. In addition, Na nanostructures showed line width narrowing from visible toward NIR, showing their prospect operating in the NIR. To address the challenges associated with the high reactivity of Na, we designed a simple encapsulation strategy and stabilized the Na nanostructures in ambient conditions for more than two months. As a low-cost and low-loss plasmonic material, Na offers a competitive option for nanophotonic devices and plasmon-enhanced applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2022

Observation of an intermediate state during lithium intercalation of twisted bilayer MoS2

Abstract Lithium intercalation of MoS 2 is generally believed to introduce a phase transition from H phase (semiconducting) to T phase (metallic). However, during the intercalation process, a spatially sharp boundary is usually formed between the fully intercalated T phase MoS 2 and non-intercalated H phase MoS 2 . The intermediate state, i.e ., lightly intercalated H phase MoS 2 without a phase transition, is difficult to investigate by optical-microscope-based spectroscopy due to the narrow size. Here, we report the stabilization of the intermediate state across the whole flake of twisted bilayer MoS 2 . The twisted bilayer system allows the lithium to intercalate from the top surface and enables fast Li-ion diffusion by the reduced interlayer interaction. The E 2g Raman mode of the intermediate state shows a peak splitting behavior. Our simulation results indicate that the intermediate state is stabilized by lithium-induced symmetry breaking of the H phase MoS 2 . Our results provide an insight into the non-uniform intercalation during battery charging and discharging, and also open a new opportunity to modulate the properties of twisted 2D systems with guest species doping in the Moiré structures.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Dynamic spatial progression of isolated lithium during battery operations

The increasing demand for next-generation energy storage systems necessitates the development of high-performance lithium batteries. Unfortunately, current Li anodes exhibit rapid capacity decay and a short cycle life, owing to the continuous generation of solid electrolyte interface and isolated Li (i-Li). The formation of i-Li during the nonuniform dissolution of Li dendrites leads to a substantial capacity loss in lithium batteries under most testing conditions. Because i-Li loses electrical connection with the current collector, it has been considered electrochemically inactive or ‘dead’ in batteries. In this work, contradicting this commonly accepted presumption, we show that i-Li is highly responsive to battery operations, owing to its dynamic polarization to the electric field in the electrolyte. Simultaneous Li deposition and dissolution occurs on two ends of the i-Li, leading to its spatial progression toward the cathode (anode) during charge (discharge). Revealed by our simulation results, the progression rate of i-Li is mainly affected by its length, orientation and the applied current density. Moreover, we successfully demonstrate the recovery of i-Li in Cu–Li cells with >100% Coulombic efficiency and realize LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC)–Li full cells with extended cycle life.

25 ENERGY STORAGE↗

DOE OSTI2020

Ultralight and fire-extinguishing current collectors for high-energy and high-safety lithium-ion batteries

Inactive components and safety hazards are two critical challenges in realizing high-energy lithium-ion batteries. Metal foil current collectors with high density are typically an integrated part of lithium-ion batteries yet deliver no capacity. Meanwhile, high-energy batteries can entail increased fire safety issues. Here we report a composite current collector design that simultaneously minimizes the ‘dead weight’ within the cell and improves fire safety. An ultralight polyimide-based current collector (9 μm thick, specific mass 1.54 mg cm-2) is prepared by sandwiching a polyimide embedded with triphenyl phosphate flame retardant between two superthin Cu layers (~500 nm). Compared to lithium-ion batteries assembled with the thinnest commercial metal foil current collectors (~6 µm), batteries equipped with our composite current collectors can realize a 16-26% improvement in specific energy and rapidly self-extinguish fires under extreme conditions such as short circuits and thermal runaway.

25 ENERGY STORAGE↗

DOE OSTI2020

Designing hierarchical nanoporous membranes for highly efficient gas adsorption and storage

Nanoporous membranes with two-dimensional materials such as graphene oxide have attracted attention in volatile organic compounds (VOCs) and H 2 adsorption because of their unique molecular sieving properties and operational simplicity. However, agglomeration of graphene sheets and low efficiency remain challenging. Therefore, we designed hierarchical nanoporous membranes (HNMs), a class of nanocomposites combined with a carbon sphere and graphene oxide. Hierarchical carbon spheres, prepared following Murray’s law using chemical activation incorporating microwave heating, act as spacers and adsorbents. Hierarchical carbon spheres preclude the agglomeration of graphene oxide, while graphene oxide sheets physically disperse, ensuring structural stability. The obtained HNMs contain micropores that are dominated by a combination of ultramicropores and mesopores, resulting in high VOCs/H 2 adsorption capacity, up to 235 and 352 mg/g at 200 ppmv and 3.3 weight % (77 K and 1.2 bar), respectively. Our work substantially expands the potential for HNMs applications in the environmental and energy fields.

42 ENGINEERING↗

DOE OSTI2020

Supercooled liquid sulfur maintained in three-dimensional current collector for high-performance Li-S batteries

In lithium-sulfur (Li-S) chemistry, the electrically/ionically insulating nature of sulfur and Li 2 S leads to sluggish electron/ion transfer kinetics for sulfur species conversion. Sulfur and Li 2 S are recognized as solid at room temperature, and solid-liquid phase transitions are the limiting steps in Li-S batteries. Here, we visualize the distinct sulfur growth behaviors on Al, carbon, Ni current collectors and demonstrate that (i) liquid sulfur generated on Ni provides higher reversible capacity, faster kinetics, and better cycling life compared to solid sulfur; and (ii) Ni facilitates the phase transition (e.g., Li 2 S decomposition). Accordingly, light-weight, 3D Ni-based current collector is designed to control the deposition and catalytic conversion of sulfur species toward high-performance Li-S batteries. This work provides insights on the critical role of the current collector in determining the physical state of sulfur and elucidates the correlation between sulfur state and battery performance, which will advance electrode designs in high-energy Li-S batteries.

25 ENERGY STORAGE↗

DOE OSTI2020

Tortuosity Effects in Lithium-Metal Host Anodes

Lithium (Li) metal is the ultimate anode material for Li batteries because of its highest capacity among all candidates. Recent research has focused on stable interphase and host materials to address its low stability and reversibility. Here, we discover that tortuosity is a critical parameter affecting the morphology and electrochemical performances of hosted Li anodes. In three types of hosts—vertically aligned, horizontally aligned, and random reduced graphene oxide (rGO) electrodes with tortuosities of 1.25, 4.46, and 1.76, respectively—we show that high electrode tortuosity causes locally higher current density on the top surface of electrodes, resulting in thick Li deposition on the surface and degraded cycling performance. Low electrode tortuosity in the vertically aligned rGO host enables homogeneous Li transport and uniform Li deposition across the host, realizing greatly improved cycling stability. Furthermore, using this principle of low tortuosity, the designed electrode shows through-electrode uniform morphology with anodic Coulombic efficiency of ~99.1% under high current and capacity cycling conditions.

25 ENERGY STORAGE↗

DOE OSTI2020

Electrochemical generation of liquid and solid sulfur on two-dimensional layered materials with distinct areal capacities

It has recently been shown that sulfur, a solid material in its elementary form S8, can stay in a supercooled state as liquid sulfur in an electrochemical cell. We establish that this newly discovered state could have implications for lithium–sulfur batteries. Here, through in situ studies of electrochemical sulfur generation, we show that liquid (supercooled) and solid elementary sulfur possess very different areal capacities over the same charging period. To control the physical state of sulfur, we studied its growth on two-dimensional layered materials. We found that on the basal plane, only liquid sulfur accumulates; by contrast, at the edge sites, liquid sulfur accumulates if the thickness of the two-dimensional material is small, whereas solid sulfur nucleates if the thickness is large (tens of nanometres). Correlating the sulfur states with their respective areal capacities, as well as controlling the growth of sulfur on two-dimensional materials, could provide insights for the design of future lithium–sulfur batteries.

36 MATERIALS SCIENCE↗