Engineering topics

Yang, Chunhui

Publications and source records attributed to Yang, Chunhui.

3 records

DOE OSTI2020

CO 2 -Assisted propane aromatization over phosphorus-modified Ga/ZSM-5 catalysts

Modification of HZSM-5 with phosphorus (P) and gallium (Ga) was found to enhance the activity of CO 2 -assisted oxidative dehydrogenation and aromatization (CO 2 -ODA) of propane to liquid aromatics. Flow reactor studies measuring the simultaneous CO 2 reduction and the CO 2 -ODA of propane were performed at 873 K at atmospheric pressure over unmodified HZSM-5 and P/Ga/ZSM-5 catalysts. At comparable propane conversion, HZSM-5 showed a high selectivity toward the undesired methane product (41.4%) with a relatively low selectivity toward aromatics (16.5%). In comparison, P/Ga/ZSM-5 demonstrated a significantly higher aromatics selectivity (42.3%) with a simultaneous reduction in methane selectivity (13.5%). Density functional theory (DFT) calculations identified the mechanisms for propane dehydrogenation and aromatization over P/Ga/ZSM-5 and the role of CO 2 . Finally cooperative with P, CO 2 addition avoided the formation of molecular H 2 and reduced the barriers for benzene formation, leading to an enhanced activity and selectivity to aromatics from CO 2 -ODA of propane over P/Ga/ZSM-5.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2018

Length-scale-dependent nanoindentation creep behaviour of Ti/Al multilayers by magnetron sputtering

This study presented length-scale-dependent room temperature creep behaviour of Ti/Al multilayers by nanoindentation. Ti/Al multilayers with individual layer thickness ranging from 10 nm to 250 nm were prepared by a direct current magnetron sputtering method. Microstructural analysis showed that the prepared Ti/Al multilayers were polycrystalline, with strong Ti (0002) and Al (111) texture. Nanoindentation creep tests were performed to examine the time-dependent creep deformation, stress exponent, creep strain rate sensitivity and contact creep compliance of the multilayers at room temperature. It was found that both the maximum creep deformation and the creep strain rate sensitivity increase with an increase in the individual layer thickness, indicating a length-scale-dependent creep behaviour of the Ti/Al multilayers. The values of stress exponent were found to lay in the range of 15.74–61.46, implying that the creep behaviour of the multilayers was controlled by the dislocation creep mechanism. Finally, the contact creep compliances of the Ti/Al multilayers were well modelled by a two-element Kelvin-Voigt model. From this, it was determined that the creep numbers and retardation times increased with increased individual layer thickness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2015

A study on atomic diffusion behaviours in an Al-Mg compound casting process

Al and Mg alloys are main lightweight alloys of research interest and they both have superb material properties, i.e., low density and high specific strength, etc. Being different from Al alloys, the corrosion of Mg alloys is much more difficult to control. Therefore to combine merits of these two lightweight alloys as a composite-like structure is an ideal solution through using Al alloys as a protective layer for Mg alloys. Compound casting is a realistic technique to manufacture such a bi-metal structure. In this study, a compound casting technique is employed to fabricate bi-layered samples using Al and Mg and then the samples are analysed using electron probe micro-analyzer (EPMA) to determine diffusion behaviours between Al and Mg. The diffusion mechanism and behaviours between Al and Mg are studied numerically at atomic scale using molecular dynamics (MD) and parametric studies are conducted to find out influences of ambient temperature and pressure on the diffusion behaviours between Al and Mg. The results obtained clearly show the effectiveness of the compound casting process to increase the diffusion between Al and Mg and thus create the Al-base protection layer for Mg.

36 MATERIALS SCIENCE↗