Search NASA⌕ Search

Engineering topics

Yang, Jihui

Publications and source records attributed to Yang, Jihui.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Deconvoluting the impact of current collector structure and electrolyte selection on Coulombic efficiency of lithium metal anodes

Lithium metal batteries are regarded as a promising avenue for significantly boosting the gravimetric energy density of batteries, particularly for electric vehicles. However, the instability of the lithium metal anode continues to hinder performance. While 3D structured current collectors for lithium metal anodes have been frequently proposed as a solution, few studies explore the impact of these structures when combined with various electrolytes and the inclusion of a lithium reservoir within the structure. This study pairs four commercially available copper current collectors with four different electrolytes to assess how these factors influence cycling performance with a 4 mAh/cm2 lithium reservoir. Coulombic efficiency (CE) measurements revealed no statistically significant difference in CE across different current collectors within the same electrolyte. However, significant variations were noted when the current collector remained intact, and the electrolyte was changed. Although polarization, electrochemical impedance, and lithium morphology varied between structures and electrolytes, no consistent patterns emerged to suggest superior performance by any specific current collector structure. Therefore, the choice of structure appears inconsequential when a lithium reservoir is present, and efforts should focus on selecting and designing the electrolyte.

White, Julia↗
DOE OSTI2024

Absence of E 2 g Nematic Instability and Dominant A 1 g Response in the Kagome Metal CsV 3 Sb 5

Ever since the discovery of the charge density wave (CDW) transition in the kagome metal CsV 3 Sb 5 , the nature of its symmetry breaking has been under intense debate. While evidence suggests that the rotational symmetry is already broken at the CDW transition temperature ( T CDW ), an additional electronic nematic instability well below T CDW has been reported based on the diverging elastoresistivity coefficient in the anisotropic channel ( m E 2 g ). Verifying the existence of a nematic transition below T CDW is not only critical for establishing the correct description of the CDW order parameter, but also important for understanding low-temperature superconductivity. Here, we report elastoresistivity measurements of CsV 3 Sb 5 using three different techniques probing both isotropic and anisotropic symmetry channels. Contrary to previous reports, we find the anisotropic elastoresistivity coefficient m E 2 g is temperature independent, except for a step jump at T CDW . The absence of nematic fluctuations is further substantiated by measurements of the elastocaloric effect, which show no enhancement associated with nematic susceptibility. On the other hand, the symmetric elastoresistivity coefficient m A 1 g increases below T CDW , reaching a peak value of 90 at T * = 20 K . Our results strongly indicate that the phase transition at T * is not nematic in nature and the previously reported diverging elastoresistivity is due to the contamination from the A 1 g channel. Published by the American Physical Society 2024

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Continuously tunable uniaxial strain control of van der Waals heterostructure devices

Uniaxial strain has been widely used as a powerful tool for investigating and controlling the properties of quantum materials. However, existing strain techniques have so far mostly been limited to use with bulk crystals. Although recent progress has been made in extending the application of strain to two-dimensional van der Waals (vdW) heterostructures, these techniques have been limited to optical characterization and extremely simple electrical device geometries. Here, we report a piezoelectric-based in situ uniaxial strain technique enabling simultaneous electrical transport and optical spectroscopy characterization of dual-gated vdW heterostructure devices. Critically, our technique remains compatible with vdW heterostructure devices of arbitrary complexity fabricated on conventional silicon/silicon dioxide wafer substrates. We demonstrate a large and continuously tunable strain of up to –0.15% at millikelvin temperatures, with larger strain values also likely achievable. We quantify the strain transmission from the silicon wafer to the vdW heterostructure, and further demonstrate the ability of strain to modify the electronic properties of twisted bilayer graphene. Our technique provides a highly versatile new method for exploring the effect of uniaxial strain on both the electrical and optical properties of vdW heterostructures and can be easily extended to include additional characterization techniques.

Electrical properties and parameters↗
DOE OSTI2024

Controlled large-area lithium deposition to reduce swelling of high-energy lithium metal pouch cells in liquid electrolytes

Lithium (Li) metal battery technology, renowned for its high energy density, faces practical challenges, particularly concerning large volume change and cell swelling. Despite the profound impact of external pressure on cell performance, there is a notable gap in research regarding the interplay between external pressure and the electroplating behaviours of Li+ in large-format pouch cells. Here we delve into the impact of externally applied pressure on electroplating and stripping of Li in 350 Wh kg –1 pouch cells. Employing a hybrid design, we monitor and quantify self-generated pressures, correlating them with observed charge–discharge processes. A two-stage cycling process is proposed, revealing controlled pouch cell swelling of less than 10%, comparable to state-of-the-art Li-ion batteries. Finally, the pressure distribution across the cell surface unveils a complex Li+ detour behaviour during electroplating, highlighting the need for innovative strategies to address uneven Li plating and enhance Li metal battery technology.

25 ENERGY STORAGE↗
DOE OSTI2023

Observation of flat and weakly dispersing bands in the van der Waals semiconductor Nb 3 Br 8 with breathing kagome lattice

Niobium halides, Nb 3 ⁢X 8 (X=Cl,Br,I), which are predicted two-dimensional magnets, have recently gotten attention due to their breathing kagome geometry. Here we have studied the electronic structure of Nb 3⁢ Br 8 by using angle-resolved photoemission spectroscopy (ARPES) and first-principles calculations. ARPES results depict the presence of multiple flat and weakly dispersing bands. These bands are well explained by the theoretical calculations, which show they have Nbd character indicating their origination from the Nb atoms forming the breathing kagome plane. This van der Waals material can be easily thinned down via mechanical exfoliation to the ultrathin limit and such ultrathin samples are stable as depicted from the time-dependent Raman spectroscopy measurements at room temperature. Finally, these results demonstrate that Nb 3 ⁢Br 8 is an excellent material not only for studying breathing kagome induced flat band physics and its connection with magnetism but also for heterostructure fabrication and for practical application.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Interfacial Engineering and Modeling of High Energy Li Batteries

In the past 6 years, the UW team have collaborated extensively with the Battery500 Consortium team members, including The Pacific Northwest National Lab, The Idaho National Lab, Binghamton University, and UT Austin. We have accomplished all milestones and deliverables at the end of the program.

25 ENERGY STORAGE↗
DOE OSTI2022

Future energy infrastructure, energy platform and energy storage

Today fossil energy dominates energy consumption across the world. There has been an increasing momentum to reduce fossil energy consumption and increase renewable energy utilization to more than 70%. Such high penetrations of distributed renewable resources bring large uncertainty and complexity that cannot be easily handled by the current infrastructure. For the last two decades, telecommunication industry has gone through a similar transition from centralized to distributed systems, and more recently to platform approaches, which become the corner stone of today’s vibrant platform economy. Based on telecommunication history, we believe that a platform-based approach, called the energy platform, is a viable solution for addressing the renewable energy challenges. The energy platform consists of an array of computational algorithms, sensing and control technologies for key industry, energy generators and users to jointly manage and control the complex energy infrastructure. It includes the following key components: (1) the hardware and software to generate, store, control and transmit electricity/data (the energy cloud), (2) the digital platforms and tools for key energy producers, digital, service and communication industry to share the assets, participate in and manage the complex infrastructure, and for customers to participate in energy transactions, (3) the transaction platform for new service and business models. Additionally, the energy platform requires breakthroughs in large scale energy storage and many other areas including efficient power electronics, sensors and controls, new mathematical and computational tools, and deep integration of energy technologies and information sciences to control and stabilize such complex chaotic systems.

25 ENERGY STORAGE↗
DOE OSTI2021

The Quest for Stable Potassium‐Ion Battery Chemistry

Abstract Potassium‐ion batteries (KIBs) have attracted wide interest for energy storage because of the abundance of the electrode materials involved; however, their electrochemical performances are far behind what can be achieved from lithium‐ion batteries (LIBs) or sodium‐ion batteries (SIBs). Herein, key promising electrode and electrolyte materials for potassium‐ion batteries are identified, the coupled electrochemical reactions in the cell are investigated, and the compatibility between different materials is demonstrated to play the most important role. K 2 Mn[Fe(CN) 6 ] cathode can deliver a high capacity of ≈125 mAh g −1 and exceptional cycling stability over 61 000 cycles (≈9 months) if the side reactions from the anode can be prevented. Graphite is a good anode material but is subjected to degradation in traditional carbonate electrolytes. New concentrated electrolytes are developed and evaluated. A stable KIB system is demonstrated by coupling a stable K 2 Mn[Fe(CN) 6 ] cathode, a prepotassiated graphite anode with a concentrated electrolyte to achieve a high energy density of ≈260 Wh kg −1 (based on the active mass of cathode and anode) and good cycling of over 1000 cycles.

Wu, Xianyong↗
DOE OSTI2021

Axion Dark Matter Experiment: Detailed design and operations

Axion dark matter experiment ultra-low noise haloscope technology has enabled the successful completion of two science runs (1A and 1B) that looked for dark matter axions in the 2.66–3.1 μeV mass range with Dine–Fischler–Srednicki–Zhitnisky sensitivity. Therefore, it is the most sensitive axion search experiment to date in this mass range. Here, we discuss the technological advances made in the last several years to achieve this sensitivity, which includes the implementation of components, such as the state-of-the-art quantum-noise-limited amplifiers and a dilution refrigerator. Furthermore, we demonstrate the use of a frequency tunable microstrip superconducting quantum interference device amplifier in run 1A, and a Josephson parametric amplifier in run 1B, along with novel analysis tools that characterize the system noise temperature.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

All solid thick oxide cathodes based on low temperature sintering for high energy solid batteries

Solid-state batteries (SSBs) could significantly improve the safety and energy density over conventional liquid cells. One key enabling technology is the use of solid electrolytes. NASICON-type Li 1.3 Al 0.3 Ti 1.7 (PO 4 ) 3 (LATP) is a very attractive solid-state electrolyte for the cathode side due to its high oxidation potential and high ionic conductivity. The usage, however, is limited by its large interfacial resistance against most of the cathode materials as well as the thermodynamic instability during high temperature sintering needed to achieve high mass density. Here we construct thin, percolative, and mixed conductive interphases through in situ low-melting-point liquid sintering. These mixed conductive interphases drastically improve the kinetics, leading to high-loading solid LATP/LiCoO 2 cathodes achieving capacity loading of up to ~6 mA h cm –2 . The technique is also applicable to Ni-rich cathode materials, achieving up to ~10 mAh cm –2 , which can lead to more than 400 W h kg –1 cells in SSBs. Furthermore, our composite cathodes show a ten-times and three-times area capacity improvement over the state-of-the-art cathodes using oxide and sulfide SSEs, respectively.

25 ENERGY STORAGE↗
DOE OSTI2021

Systematic Evaluation of Carbon Hosts for High-Energy Rechargeable Lithium-Metal Batteries

Rechargeable lithium batteries (RLBs) have attracted wide attention for achieving high energy and low cost, but the poor stability of the Li anode has remained as a large challenge. In the last several years, great efforts have been made to develop carbon anode structures for RLB applications. A wide range of carbon structures as well as many chemical modification strategies have been investigated to improve the Coulombic efficiency and extend the cycle life of the anodes or the cells. However, currently there is no clear conclusion on key factors that determine the performance of such the types of carbon structures due to the wide range of experimental conditions used in such studies. In this study, we systematically evaluated and compared the electrochemical properties of representative carbon anode materials as well as chemically functionalized carbon materials in different electrolytes. We have found that chemical functionalization, metallic loading, and the types of micro or nano-structures all have an effect on Li deposition/stripping process, but by far the most critical factor is the nature of the electrolytes. All carbon materials produced poor Coulombic efficiency and cycle life in conventional carbonate or ether-based electrolytes. However, when a Li metal compatible is used, the average Coulombic efficiency of Li metal deposition on all carbon structures is increased to 99% or higher. This study provides critical lessons on the directions for carbon anodes for RLBs. Based on these findings, we constructed Li metal coin cells using prelithiated hard carbon, LiNi0.6Mn0.2Co0.2O2 (NMC622) cathode, and compatible electrolyte and tested the cells under conditions of lean electrolyte, lean Li metal and high cathode loading required for more than 300 Wh kg-1 specific energy. More than 200 stable cycles were demonstrated with over 80% capacity retention. Furthermore, the existing challenges and potential approaches have been discussed to further extend the cyclability of lithium-metal batteries under practical conditions.

Liu, Yao↗
DOE OSTI2021

Multifunctional, Self-Healing Polyelectrolyte Gels for Long-Cycle-Life, High-Capacity Sulfur Cathodes in Li-S Batteries (FY2020 Final Report)

The project aims to develop polyelectrolyte gels consisting of partially crosslinked ionomer, interpenetrated with self-healing/polysulfide-trapping chains and swelled with a mixture of room temperature ionic liquid (RTIL) and lithium salt. To our knowledge, no other sulfur-based cathode design has combined self-healing behavior, polysulfide containment, and lithium dendrite suppression into a single design. We have demonstrated the benefits of multifunctional ionomer gel polyelectrolytes / gel cathodes with self-healing properties, as well as chemical modification of mesoporous carbons for S/C composite cathodes. Success of the proposed program of study would have wide ranging impact on the electric vehicle industry and society as a whole. A Li-S battery system with the capability of doubling lithium-ion energy density would enable the production of lighter, longer range electric vehicles at a cost that is affordable to the average U.S. household. The availability of such vehicles should lead to wide-ranging adoption over the coming years which, in combination with increased renewable electricity generation, will drastically decrease carbon emissions across the country and reduce U.S. dependency on fossil fuel sources.

25 ENERGY STORAGE↗
DOE OSTI2021

Axion dark matter experiment: Run 1B analysis details

Searching for axion dark matter, the ADMX Collaboration acquired data from January to October 2018, over the mass range 2.81–3.31 μeV, corresponding to the frequency range 680–790 MHz. Using an axion haloscope consisting of a microwave cavity in a strong magnetic field, the ADMX experiment excluded Dine-Fischler-Srednicki-Zhitnisky (DFSZ) axions at 90% confidence level and 100% dark matter density over this entire frequency range, except for a few gaps due to mode crossings. This paper explains the full ADMX analysis for run 1B, motivating analysis choices informed by details specific to this run.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Electron-phonon coupling and superconductivity in the doped topological crystalline insulator ( Pb 0.5 Sn 0.5 ) 1 – x In x Te

Here, we present a neutron-scattering study of phonons in single crystals of ( Pb 0.5 Sn 0.5 ) 1 – x In x Te with x = 0 (metallic, but nonsuperconducting) and x = 0.2 (nonmetallic normal state, but superconducting). We map the phonon dispersions (more completely for x = 0 ) and find general consistency with theoretical calculations, except for the transverse and longitudinal optical (LO) modes at the Brillouin-zone center. At low temperature, both modes are strongly damped but sit at a finite energy ( ≈ 4 meV in both samples), shifting to higher energy at room temperature. These modes are soft due to a proximate structural instability driven by the sensitivity of Pb-Te and Sn-Te p -orbital hybridization to off-center displacements of the metal atoms. The impact of the soft optical modes on the low-energy acoustic modes is inferred from the low thermal conductivity, especially at low temperature. Given that the strongest electron-phonon coupling is predicted for the LO mode, which should be similar for both studied compositions, it is intriguing that only the In-doped crystal is superconducting. In addition, we observe elastic diffuse (Huang) scattering that is qualitatively explained by the difference in Pb-Te and Sn-Te bond lengths within the lattice of randomly distributed Pb and Sn sites. We also confirm the presence of anomalous diffuse low-energy atomic vibrations that we speculatively attribute to local fluctuations of individual Pb atoms between off-center sites.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Blocking Ion Migration Stabilizes the High Thermoelectric Performance in Cu 2 Se Composites

The applications of mixed ionic–electronic conductors are limited due to phase instability under a high direct current and large temperature difference. Here, it is shown that Cu 2 Se is stabilized through regulating the behaviors of Cu + ions and electrons in a Schottky heterojunction between the Cu 2 Se host matrix and in-situ-formed BiCuSeO nanoparticles. The accumulation of Cu + ions via an ionic capacitive effect at the Schottky junction under the direct current modifies the space-charge distribution in the electric double layer, which blocks the long-range migration of Cu + and produces a drastic reduction of Cu + ion migration by nearly two orders of magnitude. Moreover, this heterojunction impedes electrons transferring from BiCuSeO to Cu 2 Se, obstructing the reduction reaction of Cu + into Cu metal at the interface and hence stabilizes the β-Cu 2 Se phase. Furthermore, incorporation of BiCuSeO in Cu 2 Se optimizes the carrier concentration and intensifies phonon scattering, contributing to the peak figure of merit ZT value of ≈2.7 at 973 K and high average ZT value of ≈1.5 between 400 and 973 K for the Cu 2 Se/ BiCuSeO composites. Here, this discovery provides a new avenue for stabilizing mixed ionic–electronic conduction thermoelectrics, and gives fresh insights into controlling ion migration in these ionic-transport-dominated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Understanding and applying coulombic efficiency in lithium metal batteries

Coulombic Efficiency (CE) has been widely used in battery research as a quantifiable monitor to compare the properties and performances of materials, electrolytes, interfaces and the entire electrochemical cells. While CE with ultra high precision effectively predicts the lifespan and health for lithium ion (Li-ion) batteries, it is not necessarily true in rechargeable lithium (Li) metal batteries. A large variation of CE is often seen even from the same materials and electrolytes in Li metal cells. This work discusses the fundamental definition of CE in different configurations of Li metal-based cells. The similarities and differences of CE in Li-ion and Li metal cells have been clarified and used to understand the relevance/irrelevance between CE and cycling. Long-standing goal of this study is to help rational design of cell testing protocols and elaborate electrochemical results. The insights from this work are broadly applicable in many other rechargeable metal cells e.g., Zn, Mg and Na batteries to accelerate reseach innovation.

Xiao, Jie↗