High-Performance Pseudocubic Thermoelectric Materials from Non-cubic Chalcopyrite Compounds
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Yang, Jihui.
Explore the source record for details and available documents.
Thermoelectric devices, intended for placement in the exhaust of a hydrocarbon fuelled combustion device and particularly suited for use in the exhaust gas stream of an internal combustion engine propelling a vehicle, are described. Exhaust gas passing through the device is in thermal communication with one side of a thermoelectric module while the other side of the thermoelectric module is in thermal communication with a lower temperature environment. The heat extracted from the exhaust gasses is converted to electrical energy by the thermoelectric module. The performance of the generator is enhanced by thermally coupling the hot and cold junctions of the thermoelectric modules to phase-change materials which transform at a temperature compatible with the preferred operating temperatures of the thermoelectric modules. In a second embodiment, a plurality of thermoelectric modules, each with a preferred operating temperature and each with a uniquely-matched phase-change material may be used to compensate for the progressive lowering of the exhaust gas temperature as it traverses the length of the exhaust pipe.
Type I clathrates, with compositions based on Ba8Ga16Ge30, are a class of promising thermoelectric materials due to their intrinsically low thermal conductivity. It has been demonstrated previously that the thermoelectric performance can be improved by transition metal substitution of the framework atoms. In this study, the effects of Au substitution for Ga/Ge on thermal and electrical transport properties of type I clathrate compounds have been investigated. Polycrystalline samples with a large range of Au content have been synthesized using conventional solid state techniques with the actual compositions of resulting materials approximately following Zintl-Klemm rules. The charge carrier type changes from electrons (n) to holes (p) as the Au content increases. The Seebeck coefficient (S) and power factor (S2/ where is the electrical resistivity) were improved by Au substitution and the resulting overall thermoelectric properties were enhanced by Au substitution with a thermoelectric figure of merit ZT ~ 0.63 at temperature T = 740 K for the composition Ba8Au5.47Ge39.96. The results presented herein show that Au-containing type I clathrates are promising p-type thermoelectric materials for high temperature applications.
Thermoelectric performance of p-type skutterudites currently lags that of the corresponding n-type materials and improvement of this important class of materials have become the focus of considerable research effort world-wide. Recent calculations find promising band structural features in p-type skutterudite materials of the type AeFe3NiSb12 ( Ae = Ca, Sr, or Ba) which could potentially lead to excellent thermoelectric properties. Recent work on the Yb- filled analog of the these formulations (YbFe3NiSb12) however finds that the onset of intrinsic conduction at lower than expected temperatures deteriorates the performance above 500 K leading to poor performance in the temperature range of interest for automotive waste heat recovery applications. We therefore seek a way to increase the band gap in order to find a way to minimize the deleterious effects of intrinsic conduction. Here we present ab initio band structure calculations and the synthesis and thermoelectric properties of YbxFe4-yPtySb12 (0.8 x 1, y = 1 and 0.5). Ab initio calculations find that the band gap increases for YbFe3PtSb12 as compared to the Ni-containing analog, though no such increase in the band gap energy was found for as compared to YbFe3.5Ni0.5Sb12. The y = 1 samples shows a characteristic transition to intrinsic conduction with a decrease in the Seebeck coefficient at temperatures above 700 K. The increased carrier concentration in y = 0.5 virtually eliminates any evidence of intrinsic conduction and the Seebeck coefficients for these samples increase monotonically up to 750 K, resulting in power factors approaching 27 W/cm K2 at 750 K. These power factors combined with low thermal conductivity result in a ZT = 0.9 at 750 K for Yb0.95Fe3.5Pt0.5Sb12.
Explore the source record for details and available documents.
A method of controlling engine exhaust flow through at least one of an exhaust bypass and a thermoelectric device via a bypass valve is provided. The method includes: determining a mass flow of exhaust exiting an engine; determining a desired exhaust pressure based on the mass flow of exhaust; comparing the desired exhaust pressure to a determined exhaust pressure; and determining a bypass valve control value based on the comparing, wherein the bypass valve control value is used to control the bypass valve.
A thermoelectric material includes a multiple transition metal-doped type I clathrate crystal structure having the formula A.sub.8TM.sub.y.sub.1.sup.1TM.sub.y.sub.2.sup.2 . . . TM.sub.y.sub.n.sup.nM.sub.zX.sub.46-y.sub.1.sub.-y.sub.2.sub.- . . . -y.sub.n.sub.-z. In the formula, A is selected from the group consisting of barium, strontium, and europium; X is selected from the group consisting of silicon, germanium, and tin; M is selected from the group consisting of aluminum, gallium, and indium; TM.sup.1, TM.sup.2, and TM.sup.n are independently selected from the group consisting of 3d, 4d, and 5d transition metals; and y.sub.1, y.sub.2, y.sub.n and Z are actual compositions of TM.sup.1, TM.sup.2, TM.sup.n, and M, respectively. The actual compositions are based upon nominal compositions derived from the following equation: z=8q.sub.A-|.DELTA.q.sub.1|y.sub.1-|.DELTA.q.sub.2|y.sub.2- . . . -|.DELTA.q.sub.n|y.sub.n, wherein q.sub.A is a charge state of A, and wherein .DELTA.q.sub.1, .DELTA.q.sub.2, .DELTA.q.sub.n are, respectively, the nominal charge state of the first, second, and n-th TM.
P-type skutterudites, with nominal compositions YbxFe3.5Ni0.5Sb12 (0.8 x 1), have been synthesized by induction melting with subsequent annealing, and their thermoelectric properties evaluated from 3.5 K to 745 K to assess their suitability for thermoelectric based waste heat recovery applications. We report results for the synthesis and measurements of Seebeck coefficient (S), electrical resistivity ( ), thermal conductivity ( ), Hall coefficient (RH), and effective mass (m*/m0) of YbxFe3.5Ni0.5Sb12 (0.8 x 1). Powder x-ray diffraction and electron probe microanalysis (EPMA) show that this system has a narrow filling fraction range of x ~ 0.84 to 0.86 for Yb in the crystallographic voids. All samples show positive RH for the entire temperature range studied with carrier concentrations ranging from 9.6 1020 to 2.8 1021 cm-3 at room temperature. Relatively high values of S result in high power factors up to 17 Wcm-1K-2 at room temperature. However, large values of and a sharp reduction in the S at high temperature due to bipolar conduction prevent the attainment of high thermoelectric figure of merit.
We have prepared Ni-doped p-type skutterudites Ce{sub y}Fe{sub 4-x}Ni{sub x}Sb{sub 12} and systematically studied their thermoelectric properties. The lattice parameters of these skutterudites are found to be sensitive to both the Ni content and Ce-filling fraction. With increasing Ni content, the electrical conductivity decreases and the Seebeck coefficient increases, consistent with the expected decrease in hole concentration due to the extra electrons introduced by Ni. All Ni-doped samples possess similar band gap values. We also find that the Ni-doped Ce{sub y}Fe{sub 4-x}Ni{sub x}Sb{sub 12} system has electrical transport properties similar to those of Co-doped Ce{sub y}Fe{sub 4-x}Co{sub x}Sb{sub 12} system at a similar nominal hole concentration based on a simple charge counting. We do, however, find a pronounced bi-polar phenomenon in thermal conductivity that rapidly increases for Ni-doped samples when temperature is above 600 K. Importantly, Ni-doped samples have higher dimensionless thermoelectric figures of merit values than CeFe{sub 4}Sb{sub 12} over the entire temperature range measured. Therefore, Ni doping is useful for improving the energy conversion efficiency in applications.
Explore the source record for details and available documents.
A thermoelectric device includes a nanocomposite material with nanowires of at least one thermoelectric material having a predetermined figure of merit, the nanowires being formed in a porous substrate having a low thermal conductivity and having an average pore diameter ranging from about 4 nm to about 300 nm.
Explore the source record for details and available documents.
While materials with excellent thermoelectric performance are most desirable for higher heat to electrical energy conversion efficiency, thermoelectric materials must also be sufficiently mechanically robust to withstand the large number of thermal cycles and vibrational stresses likely to be encountered while in service, particularly in automotive applications. Further these TE materials should be composed of non-toxic and naturally abundant constituent elements and be available as both n- and p-type varieties. Skutterudite based thermoelectric materials seemingly fit this list of criteria. In this contribution we report on the synthesis, tensile fracture strengths, low temperature electrical and thermal transport properties, and coefficients of thermal expansion (CTE), of the n-type skutterudite La{sub 0.05({+-}0.01)}Ba{sub 0.07({+-}0.04)}Yb{sub 0.08({+-}0.02)}Co{sub 4.00({+-}0.01)}Sb{sub 12.02({+-}0.03)} and the p-type Ce{sub 0.30({+-}0.02)}Co{sub 2.57({+-}0.02)}Fe{sub 1.43({+-}0.02)}Sb{sub 11.98({+-}0.03)}. Both materials have tensile fracture strengths that are temperature independent up to 500 C, and are in the range of {approx}140 MPa as measured by a three point bend flexure test fixture described herein. The CTE's were measured by dual rod dilatometry and were determined to be 10.3 ppm/C for the n-type material and 11.5 ppm/C for p-type up to 450 C.
Skutterudites CoSb{sub 3} with multiple cofillers Ba, La, and Yb were synthesized and very high thermoelectric figure of merit ZT = 1.7 at 850 K was realized. X-ray diffraction of the densified multiple-filled bulk samples reveals all samples are phase pure. High-resolution scanning transmission electron microscopy (STEM) and energy dispersive X-ray spectroscopy (EDS) analysis confirm that multiple guest fillers occupy the nanoscale-cages in the skutterudites. The fillers are further shown to be uniformly distributed and the Co-Sb skutterudite framework is virtually unperturbed from atomic scale to a few micrometers. Our results firmly show that high power factors can be realized by adjusting the total filling fraction of fillers with different charge states to reach the optimum carrier density, at the same time, lattice thermal conductivity can also be significantly reduced, to values near the glass limit of these materials, through combining filler species of different rattling frequencies to achieve broad-frequency phonon scattering. Therefore, partially filled skutterudites with multiple fillers of different chemical nature render unique structural characteristics for optimizing electrical and thermal transports in a relatively independent way, leading to continually enhanced ZT values from single- to double-, and finally to multiple-filled skutterudites. The idea of combining multiple fillers with different charge states and rattling frequencies for performance optimization is also expected to be valid for other caged TE compounds.
High thermoelectric performance of a single crystal layered compound In{sub 4}Se{sub 3} was reported recently. We present here an electrical and thermal transport property study over a wide temperature range for polycrystalline samples of In{sub 4}Se{sub 3} and In{sub 4}Te{sub 3}. Our data demonstrate that these materials are lightly doped semiconductors, leading to large thermopower and resistivity. Very low thermal conductivity, below 1 W/m K, is observed. The power factors for In{sub 4}Se{sub 3} and In{sub 4}Te{sub 3} are much smaller when compared with state-of-the-art thermoelectric materials. This combined with the very low thermal conductivity results in the maximum ZT value of less than 0.6 at 700 K for In{sub 4}Se{sub 3}.
The failure stress distributions of developmental Yb0.27Co4Sb12.08 (n-type) and Ce0.86Co1.02Fe2.98Sb11.97 (p type) skutterudites were measured as a function of temperature. These thermoelectric materials are attractive candidates for use in devices under consideration for power generation sourced from intermediate to high-temperature waste heat recovery. A self-aligning, high-temperature-capable, three-point-bend fixture was developed and used to test specimens whose cross-sectional dimensions were equivalent to those typically used in thermoelectric device legs. The strength of the n-type skutterudite was approximately 115 MPa and independent of temperature to 500 C. The strength of the p-type skutterudite was equivalent to that of the n type material and independent of temperature to at least 200 C, but its strength dropped by ~20% at 400 C. Compared to other skutterudites, the herein tested compositions have equivalent or even superior strength.