Engineering topics
Yang, Ke
Publications and source records attributed to Yang, Ke.
Pressure-induced permanent annihilation of free volume in L a 75 A l 25 metallic glasses
Not provided.
Ammonia Electrosynthesis from Nitrate Using a Ruthenium–Copper Cocatalyst System: A Full Concentration Range Study
Electrochemical synthesis of ammonia via the nitrate reduction reaction (NO3RR) has been intensively researched as an alternative to the traditional Haber–Bosch process. Most research focuses on the low concentration range representative of the nitrate level in wastewater, leaving the high concentration range, which exists in nuclear and fertilizer wastes, unexplored. The use of a concentrated electrolyte (≥1 M) for higher rate production is hampered by poor hydrogen transfer kinetics. Herein, we demonstrate that a cocatalytic system of Ru/Cu 2 O catalyst enables NO3RR at 10.0 A in 1 M nitrate electrolyte in a 16 cm 2 flow electrolyzer, with 100% faradaic efficiency toward ammonia. Detailed mechanistic studies by deuterium labeling and operando Fourier transform infrared (FTIR) spectroscopy allow us to probe the hydrogen transfer rate and intermediate species on Ru/Cu 2 O. Ab initio molecular dynamics (AIMD) simulations reveal that adsorbed hydroxide on Ru nanoparticles increases the density of the hydrogen-bonded water network near the Cu 2 O surface, which promotes the hydrogen transfer rate. Finally, our work highlights the importance of engineering synergistic interactions in cocatalysts for addressing the kinetic bottleneck in electrosynthesis.
X-ray Absorption Spectroscopy Studies of a Molecular CO 2 -Reduction Catalyst Deposited on Graphitic Carbon Nitride
Metal-ligand complexes have been extensively explored as well-defined molecular catalysts in small molecule activation reactions such as carbon dioxide (CO 2 ) reduction. Many hybrid photocatalysts have been prepared by coupling such complexes with photoactive surfaces for use in solar CO 2 reduction. In this work, we employ X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) spectroscopies, density functional theory (DFT) and computational XANES modeling to interrogate the structure of a hybrid photocatalyst consisting of a macrocyclic cobalt complex deposited on graphitic carbon nitride (C 3 N 4 ). Results show that the cobalt complex binds on C 3 N 4 through surface OH or NH 2 groups. By refining the local geometry and binding sites of this well-defined molecular cobalt complex on C 3 N 4 , here we established an important benchmark for modeling a large class of molecular catalysts that can be adapted to in situ/operando studies and further enhanced by applying chemometrics-based approaches and machine learning methods of XANES data analysis.
Observation of three superconducting transitions in the pressurized CDW-bearing compound TaTe 2
Transition metal dichalcogenides host a wide variety of lattice and electronic structures, as well as corresponding exotic physical properties, especially under certain tuning conditions. Here, we report the observation of pressure-induced three superconducting transitions in TaTe 2 , a charge density wave (CDW)–bearing layered transition-metal dichalcogenide that is metallic but not superconducting at ambient pressure. We find that its CDW state can be easily suppressed upon increasing pressure up to ~1 GPa. A superconducting state then emerges from the suppressed CDW state and persists to the pressure about 7 GPa. Unexpectedly, another superconducting state appears at ~11 GPa within the same monoclinic (M) structure of its ambient-pressure one. Upon further compression to 21 GPa, a third superconducting state with higher T c appears from a high-pressure (HP) phase. Our experimental results suggest that the pressure-induced three superconducting transitions in TaTe 2 are, respectively, driven by the suppression of the CDW state, the change of the β angle in the M phase and the transition of M-to-HP phase. Finally, these results demonstrate not only the versatile nature of this correlated electron system, but also the first experimental example that shows the pressure-induced evolution from a CDW state to three superconducting states driven by different mechanisms.
Study the existing form of copper ( p-type oxide/segregation ) and its release mechanism from the passive film of Ti-7Cu alloy
For this work, the existing form of copper and its release mechanism from the passive film of Ti-7Cu alloy was studied by Quantitative analysis of depth profile and series of electrochemical tests. Results were interpreted within the Point Defect Model-II. Copper does not form any p-type (cuprous or cupric) oxide but preferentially oxidises at the metal/film interface and segregated as Cu interstitials ($Cu^+_i$) and become substituted as $Cu^{x'}_{Ti}$ in the oxygen-deficient TiO 2-x barrier layer having n-type semiconducting character. Eventually, the segregated species of Cu preferentially dissolute through the film as Cu ions into the solution at film/solution interface via the Esaki-tunnelling effect.
Effect of Cu on the passivity of Ti–xCu (x = 0, 3 and 5 wt%) alloy in phosphate-buffered saline solution within the framework of PDM-II
The effect of copper content on the passivity of Ti–xCu alloys in a phosphate-buffered saline electrolyte (pH 7.4), in the steady-state condition, was examined using potentiostatic polarization, electrochemical impedance spectroscopy, and Mott-Schottky analysis. The study demonstrates that the oxide layer forms on the Ti–xCu alloys surface have n-type semiconducting character, and the steady-state thickness of the oxide layer is observed linearly and depends on the applied potential. The study observations are in line with the predictions of the Point Defect Model (PDM-II), which provides a physiochemically realistic description of the oxide layer formation on Ti–xCu alloys. The observations reveal that the Cu additions result in a decrease in the charge transfer resistance and capacitances associated with the hydroxide and barrier layer, an increase in the donor density, and reduce the electrochemical resistance of the Ti–xCu alloys. The study also exhibits that the decrease in the steady-state current density after the initial addition of 3 wt% of Cu is attributed to the progressive substitution of copper on the cation sublattice of the film resulting in enhanced electrostatic interaction between the immobilized copper $Cu^{x'}_{Ti}$, and the mobile cation interstitials $Cu^{+}_{i}$, which carries the excess current over and that conveyed by oxygen vacancies $V^{••}_o$ in the barrier layer. Moreover, it is also observed that over a hundred-year implant period, about 0.006 cm (0.06 mm) of Ti–3Cu alloy is predicted to lose due to steady-state corrosion in the PBS solution under the given set of conditions, it is further seen that, as the Cu amount increased from 3 wt% to 5 wt% in the Ti–xCu alloys, the steady-state corrosion rate decreases.
Tuning 2D magnetism in Fe 3+X GeTe 2 films by element doping
Two-dimensional (2D) ferromagnetic materials have been discovered with tunable magnetism and orbital-driven nodal-line features. Controlling the 2D magnetism in exfoliated nanoflakes via electric/magnetic fields enables a boosted Curie temperature (T C ) or phase transitions. One of the challenges, however, is the realization of high T C 2D magnets that are tunable, robust and suitable for large scale fabrication. Here, we report molecular-beam epitaxy growth of wafer-scale Fe 3+X GeTe 2 films with T C above room temperature. By controlling the Fe composition in Fe 3+X GeTe 2 , a continuously modulated T C in a broad range of 185–320 K has been achieved. This widely tunable T C is attributed to the doped interlayer Fe that provides a 40% enhancement around the optimal composition X = 2. We further fabricated magnetic tunneling junction device arrays that exhibit clear tunneling signals. Our results show an effective and reliable approach, i.e. element doping, to producing robust and tunable ferromagnetism beyond room temperature in a large-scale 2D Fe 3+X GeTe 2 fashion.
Pressure-induced spin crossover in a Fe 78 Si 9 B 13 metallic glass
The pressure effect on structures and properties of a Fe 78 Si 9 B 13 metallic glass was investigated by in situ high-pressure synchrotron Fe Kβ x-ray emission spectroscopy and x-ray diffraction, and electrical resistivity measurements up to ~51 GPa. The study reveals a reversible and continuous pressure-induced high- to low-spin crossover of Fe atoms in an amorphous structure. The changes of the local spin moment can be scaled to match its average atomic distance shrinkage very well during compression. The crossover of electronic spin states in the Fe 78 Si 9 B 13 metallic glass resembles that of typical crystalline Fe-bearing materials but without a sharp atomic volume collapse and an abrupt electrical resistivity jump. Furthermore, these findings could help guide applications of Fe-based metallic glasses as a soft ferromagnetic material at extreme conditions and also improve our understanding of magnetism and coupling of its changes with disordered atomic structures and other properties in metallic glasses.
High Energy Density and Stable Three-Dimensionally Structured Se-Loaded Bicontinuous Porous Carbon Battery Electrodes
Here, 3D structured Se-loaded bicontinuous porous carbon (BPC) electrodes were fabricated through colloidal templating of BPC followed by pulsed-voltage Se electrodeposition. The resultant electrodes were found to deliver a specific capacity of 665 mA h g -1 at a rate of 0.1 C, near the theoretical value for Se. When a vinylene carbonate containing electrolyte was utilized, the capacity fade over 500 cycles at 1 C rate was as small as a few percent. Impedance measurements and physical characterization of cycled electrodes indicated the exceptionally stable cycling performance was possibly due to vinylene carbonate resulting in formation of a stable SEI during cycling. Along with cycling stability, the rate performance of the 3D Se/BPC electrodes was also good. Due to the bicontinuous structure of carbonaceous current collector at rates as high as 5 C, the deliverable capacity was about 300 mA h g -1 .
Structural transitions of 4:1 methanol–ethanol mixture and silicone oil under high pressure
A 4:1 (volume ratio) methanol–ethanol (ME) mixture and silicone oil are two of the most widely used liquid pressure-transmitting media (PTM) in high-pressure studies. Their hydrostatic limits have been extensively studied using various methods; however, the evolution of the atomic structures associated with their emerging nonhydrostaticity remains unclear. Here, we monitor their structures as functions of pressure up to ∼30 GPa at room temperature using in situ high-pressure synchrotron x-ray diffraction (XRD), optical micro-Raman spectroscopy, and ruby fluorescence spectroscopy in a diamond anvil cell. No crystallization is observed for either PTM. The pressure dependence of the principal diffraction peak position and width indicates the existence of a glass transition in the 4:1 ME mixture at ∼12 GPa and in the silicone oil at ∼3 GPa, beyond which a pressure gradient emerges and grows quickly with pressure. There may be another liquid-to-liquid transition in the 4:1 ME mixture at ∼5 GPa and two more glass-to-glass transitions in the silicone oil at ∼10 GPa and ∼16 GPa. By contrast, Raman signals only show peak weakening and broadening for typical structural disordering, and Raman spectroscopy seems to be less sensitive than XRD in catching these structural transitions related to hydrostaticity variations in both PTM. These results uncover rich pressure-induced transitions in the two PTM and clarify their effects on hydrostaticity with direct structural evidence. The high-pressure XRD and Raman data on the two PTM obtained in this work could also be helpful in distinguishing between signals from samples and those from PTM in future high-pressure experiments.
Probing the Electronic Band Gap of Solid Hydrogen by Inelastic X-Ray Scattering up to 90 GPa
Metallization of hydrogen as a key problem in modern physics is the pressure-induced evolution of the hydrogen electronic band from a wide-gap insulator to a closed gap metal. However, due to its remarkably high energy, the electronic band gap of insulating hydrogen has never before been directly observed under pressure. Using high-brilliance, high-energy synchrotron radiation, we developed an inelastic x-ray probe to yield the hydrogen electronic band information in situ under high pressures in a diamond-anvil cell. Here, the dynamic structure factor of hydrogen was measured over a large energy range of 45 eV. The electronic band gap was found to decrease linearly from 10.9 to 6.57 eV, with an 8.6 times densification (ρ/ρ 0 ~ 8.6 ) from zero pressure up to 90 GPa.
Chalcogenide Perovskite YScS 3 as a Potential p-Type Transparent Conducting Material
Transparent conducting materials (TCMs) have been widely used in optoelectronic applications such as touchscreens, flat panel displays and thin film solar cells. These applications of TCMs are currently dominated by n-type doped oxides. High-performance p-type TCMs are still lacking due to their low hole mobility or p-type doping bottleneck, which impedes efficient device design and novel applications such as transparent electronics. Here, based on first-principles calculations, we propose chalcogenide perovskite YScS 3 as a promising p-type TCM. According to our calculations, its optical absorption onset is above 3 eV, which allows transparency to visible light. Its hole conductivity effective mass is 0.48m 0 , which is among the smallest in p-type TCMs, suggesting enhanced hole mobility. It could be doped to p-type by group-II elements on cation sites, all of which yield shallow acceptors. Here, combining these properties, YScS 3 holds great promise to enhancing the performance of p-type TCMs toward their n-type counterparts.
Octahedron rotation evolution in 2D perovskites and its impact on optoelectronic properties: the case of Ba–Zr–S chalcogenides
Octahedron rotation (OR) is a unique structural feature in most perovskite materials. During dimensional reduction from bulk to two-dimensional (2D) perovskites, how the OR pattern evolves is still an open question. Here, we employ an adapted Glazer's notation from bulk perovskites to systematically study the structural evolution of 2D perovskites by fully considering the possible OR patterns. Applying this approach to the 2D Ba–Zr–S system, we establish the relationship between the OR pattern and slab thickness. It is found that as the thickness decreases, the OR pattern undergoes a transition by suppressing out-of-plane rotations. The OR in 2D chalcogenide perovskites could result in an anti-confinement effect, i.e., reducing the band gap to even below that of the bulk by countering the quantum confinement effect. In addition, we show that the Ba–Zr–S 2D perovskites exhibit reasonable electron mobility of ~150 cm 2 V –1 s –1 and large exciton binding energy of ~0.9 eV. In conclusion, combining the slab thickness and strain as effective knobs for widely tuning the electronic structure, we suggest the 2D chalcogenide perovskites as promising optoelectronic materials.
Metastable oxygen vacancy ordering state and improved memristive behavior in TiO2 crystals
Not Available
Hall-coefficient diagnostics of the surface state in pressurized SmB 6
In this study, we report results of the high-pressure Hall coefficient (R H ) measurements in the putative topological Kondo insulator SmB 6 up to 37 GPa. Below 10 GPa, our data reveal that R H (T) exhibits a prominent peak upon cooling below 20 K. Remarkably, the temperature at which surface conduction dominates coincides with the temperature of the peak in R H (T). The temperature dependent resistance and Hall coefficient can be well fitted by a two-channel model with contributions from the metallic surface and the thermally activated bulk states. When the bulk of SmB 6 becomes metallic and magnetic at ~10 GPa, both the R H (T) peak and the resistance plateau disappear simultaneously. Here, our results indicate that the R H (T) peak is a fingerprint to diagnose the presence of a metallic surface state in SmB 6 . The high-pressure magnetic state of SmB 6 is robust to 180 GPa, and no evidence of superconductivity is observed in the metallic phase.