Engineering topics

Yang, L. C.

Publications and source records attributed to Yang, L. C..

At least 19 records

NASA NTRS1986

Measuring Combustion Advance in Solid Propellants

Set of gauges on solid-propellant rocket motor with electrically insulating case measures advance of combustion front and local erosion rates of propellant and insulation. Data furnished by gauges aid in motor design, failure analysis, and performance prediction. Technique useful in determining propellant uniformity and electrical properties of exhaust plum. Gauges used both in flight and on ground. Foilgauge technique also useful in basic research on pulsed plasmas or combustion of solids.

Yang, L. C.↗

NASA NTRS1986

Erosive burning research

A status report is given on the results for the completed tests in a series of motor firings being carried out to measure the effects of the parameters that are considered to most strongly influence the scaling to larger rocket motor sizes of the transition to/or threshold conditions for erosive burning rate augmentation. Propellant burning rates at locations along the axis of the test motors are measured with a newly developed plasma capacitance gauge technique. The measured results are compared with erosive-burning predictions from a supporting ballistics analysis. The completed motor firings have successfully demonstrated response to the designed test variables. The trends with varying propellant burning rate, chamber pressure, and mass flow rate are consistent with existing results, but no pronounced effect of surface roughness has been observed. Rather, the influence of propellant oxidizer particle size on erosive burning is through its effect on the base, no-corssflow burning rate.

Strand, L.↗

NASA NTRS1985

Instrumentation for sensing moisture content of material using a transient thermal pulse

Instrumentation for sensing moisture content of material using a transient thermal pulse is comprised of a sensing probe having a sensing element in the form of a ribbon excited by a constant current pulse from a source to increase the temperature and therefore the resistance of the ribbon linearly. Moisture in web material will limit the increase of temperature during the pulse in proportion to the moisture content. This increase in temperature produces a proportional increase in resistivity which is measured with a wheatstone bridge as a change in voltage displayed by a measurement display unit. The probe is glued in a shallow groove of a Lucite bar and connected to copper pins embedded in the bar.

Yang, L. C.↗

NASA NTRS1985

Fiber-Optic Equipment for Power-System Control

Report surveys state of art in fiber optics and explores use of microprocessors communicating over optical fibers to control complicated power system with many producing and consuming units. Power system of study is of planetary spacecraft, and fiber-optic technology extension of that now under development or used in military aircraft and ships.

Bridgeforth, A. O.↗

NASA NTRS1984

Diesel Particulate Destruction

Pulsed electrical discharge eliminates particulates in diesel exhaust. Particulates in diesel exhaust gas destroyed by passing them through agglomerator and series of high voltage-biased grids.

Yang, L. C.↗

NASA NTRS1984

Crystal Microbalance Monitors Relative Humidity

Sensor monitors water evaporation in industrial drying processes. Measured adsorption isotherm for instrument essentially linear over entire range of relative humidity. Testing at each temperature setting less than half hour for full relative-humidity range, with estimated frequency response time less than 10 seconds. Used to measure relative humidity of ambient atmosphere near drying paper, food textile fabrics and pulp to optimize water-drying portion of processing cycle.

Yang, L. C.↗

NASA NTRS1984

Surface-Moisture Monitoring Technique

Technique monitors drying of continuous sheets of thin material. Ribbon sensing element samples moisture content of web material during each rotation of roller. Change in resistivity of thermally and electrically conductive ribbon is parameter used to measure web moisture; measurements insensitive to ribbon contact pressure. Application in industrial production of sheet materials such as paper and fabric.

Yang, L. C.↗

NASA NTRS1982

Circuit Counts Carbon Fibers

Carbon fibers are counted when they fall on high-voltage grid. An arc discharge vaporizes fiber and triggers timer. The equal-duration pulses from timer are integrated by operational amplifier, giving an output voltage that is proportional to the number of fibers incident after reset switch was opened. If two or more fibers arrive at grid simultaneously, they are vaporized one at a time; thus all of them are counted.

Yang, L. C.↗

NASA NTRS1982

Sequential-Impulse Generator Uses Fiber-Optics

Light pulse from a ruby or neodymium-glass laser enters miniature optics of repetitive-detonation apparatus. Traveling along a bundle of optical fibers, light strikes laser-sensitive microdetonator and charge explodes. Apparatus then advances next charge in train into position. Possible applications of sequential-impulse generator are in creating shock waves for aerodynamics research and in generating electrical power by magnetohydrodynamics.

Yang, L. C.↗

NASA NTRS1982

Method and device for detection of a substance

A device is disclosed in which a discharge grid is provided that has a sufficiently high voltage potential across its grid electrodes so that a substance with predetermined characteristics causes an electric spark discharge to occur between electrodes. The electric spark discharge alters the predetermined characteristics of the substance by oxidation and/or vaporization so that the substance is no longer detectable by an electric spark discharge. A means is provided for counting the number of electric spark discharges. This count indicates the concentration of the substance having the predetermined characteristics. One embodiment disclosed detects longitudinally extending carbon fibers suspended in a gaseous medium. Another embodiment provides for the detection of carbon fibers adhesively attached to a collection tape. The tape is positioned against the discharge grid and a high voltage is periodically applied across the grid electrodes until electric spark discharges no longer occur.

Yang, L. C.↗

NASA NTRS1981

Performance characteristics of a laser initiated microdetonator

The test results of 320 units of a laser initiated microdetonator are summarized. The commercially fabricated units used a lead styphnate/lead azide/HMX (1 mg/13.5 mg) explosive train design contained in a miniature aluminum can that was capped with a glass-metal seal window. The test parameters were the laser energy, temperature, laser pulse duration, laser wavelength and nuclear radiation (5,000,000 rad of 1 MeV gamma rays). The performance parameters were the laser energy for ignition and the actuation response time.

Yang, L. C.↗

NASA NTRS1981

Instrumentation for sensing moisture content of material using a transient thermal pulse

Instrumentation is developed for sensing moisture content of material using a transient thermal pulse and is comprised of a sensing probe having a sensing element in the form of a ribbon excited by a constant current pulse to increase the temperature, and therefore the resistance, of the ribbon linearly. Moisture in web material limits the increase of temperature during the pulse in proportion to the moisture content. This increase in temperature produces a proportional increase in resistivity which is measured with a Wheatsone bridge as a change in voltage displayed by a measurement display unit. The probe is glued in a shallow groove of a lucite bar and connected to copper pins embedded in the bar.

Yang, L. C.↗

NASA NTRS1981

Characterization of superfluid helium transfer

The friction factor and steady state flow rate of superfluid helium (He II) are measured, with the driving pressure difference generated by the saturated vapor pressure and a small hydrostatic pressure head. The temperature ranged from 1.5 K to the transition temperature of 2.17 K. Three different lengths and two different internal diameters were used for the stainless steel transfer tubes, and the transfer of liquid helium (He I) was investigated with the same apparatus for comparison. It was found that the friction factor of He II is greater than that of He I for pressure differences greater than 20 mm Hg, and smaller below that magnitude.

Yang, L. C.↗

NASA NTRS1980

Apparatus and method for destructive removal of particles contained in flowing fluid

An apparatus and method for destructively removing particles from a flowing gas containing the particles is described. In the specific embodiments disclosed the apparatus is adapted to remove carbon particles from diesel engine exhaust products. The exhaust products are directed to a predetermined location where they are rapidly vaporized and combine with oxygen in the exhaust products to form carbon dioxide. Vaporization in one embodiment is effected by a discharge grid located within an exhaust conduit, the grid being chosen so that alternate conductors defining the grid are spaced apart a distance approximately 125 times the mean diameter of the particles to be removed. A voltage differential of approximately 690 volts is applied across adjacent conductors.

Yang, L. C.↗

NASA NTRS1980

High-voltage spark carbon-fiber sticky-tape data analyzer

An efficient method for detecting carbon fibers collected on a stick tape monitor was developed. The fibers were released from a simulated crash fire situation containing carbon fiber composite material. The method utilized the ability of the fiber to initiate a spark across a set of alternately biased high voltage electrodes to electronically count the number of fiber fragments collected on the tape. It was found that the spark, which contains high energy and is of very short duration, is capable of partially damaging or consuming the fiber fragments. It also creates a mechanical disturbance which ejects the fiber from the grid. Both characteristics were helpful in establishing a single discharge pulse for each fiber segment.

Yang, L. C.↗

NASA NTRS1980

High voltage spark carbon fiber detection system

The pulse discharge technique was used to determine the length and density of carbon fibers released from fiber composite materials during a fire or aircraft accident. Specifications are given for the system which uses the ability of a carbon fiber to initiate spark discharge across a high voltage biased grid to achieve accurate counting and sizing of fibers. The design of the system was optimized, and prototype hardware proved satisfactory in laboratory and field tests.

Yang, L. C.↗

NASA NTRS1980

Portable heatable container

A container is provided which can be designed to heat its outer surface to sterilize it, or to heat its inner surface and any contents therewithin. In a container that self sterilizes its outer surface, the container includes a combustible layer of thermite-type pyrotechnic material which can be ignited to generate considerable heat, and a thin casing around the combustible layer which is of highly thermally conductive materials such as aluminum which can be heated to a high temperature by the ignited combustible layer. A buffer layer which may be of metal, lies within the combustible layer, and a layer of insulation such as Teflon lies within the buffer layer to insulate the contents of the container from the heat.

Yang, L. C.↗

NASA NTRS1980

Superfluid helium film in zero gravity

The behaviour of nearly-saturated superfluid helium films several hundred Angstroms thick was investigated under zero gravity conditions in a small cryostat carried on a 0.3 m diameter, 3 m long sounding rocket, using a quartz microbalance technique. The flight provided 30 s of high acceleration, about 5 min. of zero gravity, and 90 s of mg acceleration. The temperature of the experiment ranged from 1.67 to 2.15 K. In contrast to ground test results, thick films uniformly distributed on all surfaces were observed in zero gravity.

Yang, L. C.↗