Search NASA⌕ Search

Engineering topics

Yang, S.

Publications and source records attributed to Yang, S..

At least 19 records

Delivering laser performance conditions to enable fusion ignition, and beyond at the National Ignition Facility

On December 5th, 2022, controlled fusion ignition was demonstrated for the first time at the National Ignition Facility (NIF), a major achievement in the field of Inertial Confinement Fusion (ICF) requiring a multi-decadal effort involving broad national and international collaborations. To drive the fusion ignition reaction with the compressed fuel capsule, that yielded 3.15 MJ of nuclear energy [1], the NIF laser delivered a high-precision pulse shape with 2.05 MJ of ultra-violet (UV) laser energy and a peak power of 440 TW. This laser energy was an increase of ~8 % compared to that delivered on the previous “threshold of ignition” record yield experiment (1.37 MJ of yield for 1.89 MJ of laser energy) on August 8th, 2021. Here we explain how the results of our extensive research in laser technology and UV optics damage mitigation led to major improvements in the NIF laser, enabling this energy increase along with additional accuracy, precision, and power balance enhancements. Furthermore, we will discuss on-going efforts that have enabled operations at 2.2 MJ of UV energy as well as potential new initiatives to push the laser performance –accuracy and delivered energy– to even higher levels in the future as previously demonstrated on a small subset of NIF beams.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors, Volume 1

This is Volume 1 of a two-volume document that collects the verification and validation (V&V) works done for the PLTEMP/ANL code during the years of its development and improvement. Volume 1 describes the V&V of sixteen capabilities of the PLTEMP/ANL code that were identified by research reactor analysts as frequently used in their thermal-hydraulic analysis. Volume 2 describes the V&V of developments and improvements since the release of PLTEMP/ANL Version 4.3. Each chapter of the document focuses on verifying or validating a specific part of the software that calculates a specific phenomenon, e.g., channel flow calculation, coolant property calculation, heat transfer calculation, and flow instability calculation. Software verification is performed by comparing the code with hand calculation, Microsoft spreadsheet calculation, Mathematica calculation, or MATLAB calculation. The software validation is done by comparing the code with experimental data or a widely tested code like the RELAP5 code. In addition, some PLTEMP/ANL V&V works that are available in the open literature are simply cited in Volume 1 of the document. PLTEMP/ANL has been used in the safety analysis reports of several US and foreign research reactors licensed and converted from highly enriched uranium fuel to low-enriched uranium fuel. A list of such reactors is given in Volume 1 of the document.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors, Volume 2

This is Volume 2 of a two-volume document that collects the verification and validation (V&V) works done for the PLTEMP/ANL code during the years of its development and improvement. Volume 1 describes the V&V of sixteen capabilities of the PLTEMP/ANL code that were identified by research reactor analysts as frequently used in their thermal-hydraulic analysis. Volume 2 describes the V&V of developments and improvements since the release of PLTEMP/ANL Version 4.3. Each chapter of the document focuses on verifying or validating a specific part of the software that calculates a particular phenomenon, e.g., channel flow calculation, coolant property calculation, heat transfer calculation, and flow instability calculation. Software verification is performed by comparing the code with a hand calculation, Microsoft spreadsheet calculation, Mathematica calculation, or MATLAB calculation. The software validation is achieved by comparing the code with experimental data or a widely tested code like the RELAP5 code. In addition, some PLTEMP/ANL V&V works that are available in the open literature are simply referenced in Volume 1 of the document. PLTEMP/ANL has been used in safety analysis reports of several US and foreign research reactors licensed and converted from highly enriched uranium fuel to low-enriched uranium fuel. A list of such reactors is given in Volume 1 of the document.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A User’s Guide to the PLTEMP/ANL Code

PLTEMP/ANL V4.4 is a program that obtains a steady-state flow and temperature solution, in geometrical extent, for a nuclear reactor core, or a single fuel assembly, including the effect of manufacturing and modelling uncertainties by the means of hot channel factors. It is based on an evolutionary sequence of codes originally used for calculating plate temperatures, hence “PLTEMP”, developed at Argonne National Laboratory over the past 30 years. Fueled and non-fueled regions are modeled. Each fuel assembly consists of one or more plates or tubes separated by coolant channels. The fuel plates may have one to five layers of different materials, each with heat generation. The width of a fuel plate may be divided into multiple longitudinal stripes, each with its own axial power shape. Depending upon the heat transfer method selected, the temperature solution is effectively 2-dimensional or 3-dimensional. The geometry may be either slab or radial, corresponding to fuel assemblies made of a series of flat (or slightly curved) plates, or of nested tubes. A variety of thermal-hydraulic correlations are available to determine safety margins such as onset of nucleate boiling ratio (ONBR), departure from nucleate boiling ratio (DNBR), and onset of flow instability ratio (OFIR). Coolant properties for either light or heavy water are obtained from FORTRAN functions rather than from tables. The code is intended for thermal-hydraulic analysis of research reactor performance in the sub-cooled boiling regime. Both turbulent and laminar flow regimes can be modeled. Options to calculate both forced flow and natural circulation are available. A general search capability for select design and safety parameters is available to greatly reduce the reactor analyst’s time.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Optical Transmission Characterization of Fused Silica Materials Irradiated at the CERN Large Hadron Collider

The Target Absorbers for Neutrals (TANs) represent one of the most radioactive regions in the Large Hadron Collider (LHC). Seven 40 cm long fused silica rods with different dopant specifications, manufactured by Heraeus, were irradiated in one of the TANs located around the ATLAS experiment by the Beam RAte of Neutrals (BRAN) detector group. This campaign took place during the Run 2 p+p data taking, which occurred between 2016 and 2018. This paper reports a complete characterization of optical transmission per unit length of irradiated fused silica materials as a function of wavelength (240 nm - 1500 nm), dose (up to 18 MGy), and level of OH and H$_2$ dopants introduced in the manufacturing process. The dose delivered to the rods was estimated using Monte Carlo simulations performed by the CERN FLUKA team.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Optimization of Backscatter and Symmetry for Laser Fusion Experiments Using Multiple Tunable Wavelengths

A new additional wavelength-tuning capability has been implemented on the National Ignition Facility (NIF) laser allowing for unprecedented control of crossed-beam energy transfer (CBET) between all groups of beams for better performance of indirect-drive inertial confinement fusion (ICF) ignition experiments. In particular, this advance allows for negation and reversal of flow-induced CBET and the rebalancing of the intensity of different groups of beams within an indirect-drive (ICF) hohlraum. The experiments conducted at the NIF using a 1.1 MJ laser pulse with peak power of 390 TW demonstrate this high level of control through measurements of the precise changes to stimulated Brillouin scattering, typically driven by flow-induced CBET at the end of the pulse. Additionally, this new capability is shown to be able to predictably control gold-wall plasma expansion in the target driven by early-time flow-induced CBET. Estimates of early-time CBET from the wall expansion are shown to be consistent with simulation expectations. This new additional capability to control symmetry and backscatter expands the design space of current experiments and provides extra margin for increased laser energy in near-future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Na 22 activation level measurements of fused silica rods in the LHC target absorber for neutrals compared to simulations

The Target Absorbers for Neutrals (TANs) are located in a high intensity radiation environment inside the tunnel of the Large Hadron Collider (LHC). TANs are positioned about 140 m downstream from the beam interaction points. Seven 40-cm long fused silica rods with different dopant specifications were irradiated in the TAN by the Beam RAte of Neutrals (BRAN) detector group during p + p data taking from 2016 to 2018 at the LHC. The peak dose delivered to the fused silica rods was 18 MGy. We report measurements of the 22 Na activation of the fused silica rods carried out at the University of Illinois at Urbana-Champaign and Argonne National Laboratory. At the end of the irradiation campaign, the maximum 22 Na activity observed was A = 21 kBq/cm 3 corresponding to a density, ρ = 2.5 x 10 12 /cm 3 , of 22 Na nuclei. FLUKA Monte Carlo simulations have been performed by the CERN FLUKA team to estimate 22 Na activities for the irradiated BRAN rod samples. The simulations reproduce the 22 Na activity profile measured along the rods, with a 35% underestimation of the experimental measurement results.

43 PARTICLE ACCELERATORS↗

First graded metal pushered single shell capsule implosions on the National Ignition Facility

Graded metal pushered single shell (PSS) capsules are predicted to be a viable alternative to low-Z capsule indirect drive inertial confinement fusion (ICF) implosions for achieving high fusion yields [MacLaren et al., Phys. Plasmas 28, 122710 (2021)]. The first experiments with Be/Cr-graded metal PSS capsules indicate that the implementation of the principle design feature, the graded density inner metal layer, has succeeded in producing a stable implosion with performance in agreement with predictions. With 50% Cr concentration in the pusher, PSS capsules have greater than ~2× higher shell densities during stagnation for enhanced core confinement and radiation trapping at ~35% lower shell implosion velocities than low-Z capsules. High-energy >30 keV inflight shell radiography recorded 215 km/s implosion velocities and show that implosion Legendre mode P 2 asymmetry can be tuned via inner-to-outer beam wavelength separation, similar to other implosions. Shell radiographs and neutron core images show similar P 2 asymmetry, suggesting no symmetry swings between peak implosion velocity and stagnation times. Despite the modest implosion velocities, gas-filled deuterium–tritium capsule implosions generate 10 15 neutron yields at relatively modest core ion temperatures of 2.75 keV, indicating that in spite of the high-density inner layer, the implosions have been stabilized by the design density gradient. When compared with hydrodynamic simulations, the measured yield-over-simulated is 35% due to fuel–pusher mix and other perturbations such as the capsule fill tube. Finally, simple analytical scalings of hot spot pressure and neutron yield show that PSS implosions reach similar performance at lower implosion velocities and higher shell densities to low-Z ICF capsules.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Commissioning of a replacement subatmospheric cold box for Jefferson Lab’s Central Helium Liquefier

Jefferson Lab’s Cryogenics Department has designed, fabricated, installed, and commissioned a new subatmospheric cold box to replace one of the two existing units within our Central Helium Liquefier (CHL). The replacement cold box, dubbed SC1R, pumps saturated helium vapor at 0.0385 atm from Jefferson Lab’s continuous electron beam accelerator facility (CEBAF) cryomodules to maintain an operating temperature of nominally 2.1 K. This is accomplished using a five-stage cryogenic centrifugal compressor (cold compressor) system and a brazed aluminum plate-fin heat exchanger operating between 2.1 K and 4.5 K. In this paper we will describe our experience commissioning the SC1R cold box. We will discuss pump-down of the system to 2.1 K and steady-state operation at the cold compressor design flow rates of 170, 200, and 250 g/s. Performance of the heat exchanger and cold compressors has been mapped across a range of flow rates and optimized for CEBAF operations. This commissioning data will be used to monitor future performance and adapt to changing load requirements.

Mastracci, B.↗

Determination of the Al 27 Neutron Distribution Radius from a Parity-Violating Electron Scattering Measurement

In this paper, we report the first measurement of the parity-violating elastic electron scattering asymmetry on 27 Al. The 27 Al elastic asymmetry is $A_{\text{PV}}$ = 2.16 ± 0.11(stat) ± 0.16(syst) ppm, and was measured at $\langle Q^2\rangle$ = 0.02357 ± 0.00010 GeV$^2$, $\angleθ_{\text{lab}}$ = 7.61° ± 0.02°, and $\langle E_{\text{lab}}$ = 1.157 GeV with the Q weak apparatus at Jefferson Lab. Predictions using a simple Born approximation as well as more sophisticated distorted-wave calculations are in good agreement with this result. From this asymmetry the 27 Al neutron radius $R_n$ = 2.89 ± 0.12 fm was determined using a many-models correlation technique. The corresponding neutron skin thickness $R_n – R_p$ = –0.04 ± 0.12 fm is small, as expected for a light nucleus with a neutron excess of only 1. This result thus serves as a successful benchmark for electroweak determinations of neutron radii on heavier nuclei. A tree-level approach was used to extract the 27 Al weak radius $R_w$ = 3.00 ± 0.15 fm, and the weak skin thickness $R_{\text{wk}} – R_{\text{ch}}$ = –0.04 ± 0.15 fm. The weak form factor at this $Q^2$ is $F_{\text{wk}}$ = 0.39 ± 0.04.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Achieving record hot spot energies with large HDC implosions on NIF in HYBRID-E

HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths (Δλ> 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams (Δλ1-2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δλ> 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δλ, indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ~360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ~170 kJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗