Engineering topics

Yang, Songge

Publications and source records attributed to Yang, Songge.

10 records

DOE OSTI2024

High-entropy Li-rich layered oxide cathode for Li-ion batteries

High-entropy oxides (HEOs) are emerging as promising cathode materials for Li-ion batteries (LIBs) due to their stable solid-state phase and compositional flexibility. Herein, we investigate the structural and electrochemical properties of a novel non-equimolar high-entropy cathode material, termed high-entropy Li-rich layered oxide (HE-LLO, Li 1.15 Na 0.05 Ni 0.19 Mn 0.56 Fe 0.02 Mg 0.02 Al 0.02 O 1.97 F 0.03 ), in comparison to a pristine Li-rich layered oxide (PR-LLO, Li1.2Ni0.2Mn0.6O2). The incorporation of multiple cations (Na + , Al 3+ , Mg 2+ , Fe 3+ ) and anion (F - ) into HE-LLO introduces compositional diversity, enhancing structural stability through the entropy stabilization effect. Theoretical calculations confirm a significantly higher configurational entropy in HE-LLO compared to PRLLO, supporting its high-entropy nature. Electrochemical evaluations demonstrate that HE-LLO exhibits considerable capacity retention, preserving 76.8 % of its discharge capacity at 0.5C after 200 cycles, compared to only 36.2 % for PR-LLO. Even under high-temperature conditions, HE-LLO outperformed PR-LLO, maintaining 76.1 % of its discharge capacity after 100 cycles at 5C, while PR-LLO retained only 12.4 %. These enhancements are attributed to the improved phase reversibility and higher Li + ion diffusion coefficients of HE-LLO, validated by ex-situ characterizations using a synchrotron X-ray technique, along with density functional theory (DFT) calculations. In conclusion, these findings highlight the promise of non-equimolar HEOs as a novel design strategy for highperformance cathode materials.

25 ENERGY STORAGE↗

DOE OSTI2023

Ab Initio Modeling on The Thermodynamic and Temperature-Dependent Elastic Properties of Subsystems of The FCC FeNiCoCr Medium Entropy Alloys (MEAs)

The stability, phonon spectra, thermodynamic, and temperature-dependent elasticity of subsystems of the FCC FeNiCoCr MEAs are systematically studied by the ab initio approach. Especially, the quasi-harmonic approximation (QHA) and the innovative Zentropy theory were utilized to predict the thermodynamic properties and elastic properties of FeNi, NiCo, FeNiCo, and FeNiCoCr MEAs with the consideration of magnetic transition. With the ensemble of the partition function based on the multiplicity of each magnetic configuration, the current work successfully reproduced the Curie temperature and the Schottky anomaly of heat capacity of these four MEAs purely based on the ab initio input. Meanwhile, the elastic properties of these alloys at finite temperatures are also successfully predicted with the consideration of magnetic transition. The overall results agree well with the available experimental data and CALPHAD prediction.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Ab initio studies on structural and thermodynamic properties of magnetic Fe

The present work systematically investigates the total energy, phonon spectra, and thermodynamic properties of different polymorphs of pure Fe, i.e., FCC, BCC, and HCP, with the ab initio approach, considering various magnetic configurations. In general, the calculated energy vs. volume curves and phonon spectra agree well with previous calculations and the experimental data. In addition, their thermodynamic properties are estimated by the quasiharmonic approximation (QHA). Specifically, a superposition approach based on the latest Zentropy theory was utilized to predict magnetic transition temperatures and thermodynamic properties of pure Fe. With the ensemble of the partition function considering the multiplicity of each magnetic microstate, the current work successfully reproduced the Curie/Néel temperature and the Schottky anomaly of heat capacity in FCC, BCC, and HCP Fe purely based on the ab initio input, which exhibits good agreement with the experimental data and CALPHAD modeling.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Modeling assisted synthesis of Zr-doped Li 3-x In 1-x Zr x Cl 6 with ultrahigh ionic conductivity for lithium-ion batteries

All-solid-state lithium-ion batteries (ASSLBs) are an important milestone for the future of energy storage because of their capability of impressive energy density and outstanding safety. However, oxide and sulfide solid-state electrolytes (SSEs) suffer from either low ionic conductivity or poor chemical stability. In contrast, halide-based SSEs, are promising as candidate materials owing to high conductivity, good stability, and broad cathode compatibility. Though element doping of the SSEs is an effective and common approach to further improve their electrochemical properties, dopant exploration and optimization through solely experimental trials are both costly and time-consuming. For this aspect, computational simulations for dopant element and concentration screening are adopted in this research and zirconium is selected as a suitable dopant for Li 3 InCl 6 . Further, the synthesized Li 2.75 In 0.75 Zr 0.25 Cl 6 exhibited Li ionic conductivity of 5.82 x 10 -3 Scm -1 at room temperature, which is the highest among reported halide SSEs. The ASSLB formed with Li 2 CoO 2 -Li 2.75 In 0.75 Zr 0.25 Cl 6 -Li/In delivers a high initial capacity of 129.3 mAh∙g -1 . Conclusively, this work provides an effective approach which combines computational modeling and experimental verification for the development of halide SSEs with improved stability and conductivity. The successful design approach and compelling results provide further possibilities and capabilities in future SSE research.

25 ENERGY STORAGE↗

DOE OSTI2022

Energy and mechanical properties predictions in Fe-Ni binary system by ab initio calculations

Here, the fcc random solid solutions in Fe-Ni binary system were investigated using ab initio calculations. Density functional theory (DFT) was applied along with supercells generated by the Special Quasi-Random Structure (SQS) method to predict the enthalpy of mixing and magnetic and elastic properties. The results were compared with relevant experimental and computational data produced by other groups. The effect of SQS supercell size and relaxation procedure on the predicted properties of the alloys were also studied. Our calculations show that 16-atoms SQS model provides adequate approach to the mixing energy of the alloy. However, calculation of mechanical properties requires larger supercell. Excellent agreement between experimental and calculated elastic properties was found in fcc region of Fe-Ni system.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Revisit the VEC criterion in high entropy alloys (HEAs) with high-throughput ab initio calculations: A case study with Al-Co-Cr-Fe-Ni system

Valence electron concentration (VEC) was treated as a useful parameter to predict the stability of solid solution phases. However, the available experimental data to support this criterion is far from enough. In the current study, the high-throughput ab initio modeling is applied to investigate the relative stability of FCC and BCC single crystals of the Al-Co-Cr-Fe-Ni high entropy alloys (HEAs) by using the special quasi-random structure (SQS) approach. Furthermore, the predictions start with pure elements of the Al-Co-Cr-Fe-Ni system and are continued with binaries, ternaries, and quaternary compositions, which come up with 180 compositions (360 structures). After that, the reliability of the VEC criterion is testified. The results show that the VEC criterion not only works for the stable structure but also works effectively for metastable structure when both FCC and BCC are not thermodynamic stable. However, it is found that the old VEC criterion proposed by Guo et al. fails to work effectively for compositions containing high concentrations of light-weight metals such as Al at VEC<5. To solve this problem, the present work proposes a new VEC rule to define the stability of FCC and BCC structures at the ground state. With the implementation of the new VEC rule, the effectiveness of the VEC rule (EVEC) of both FCC and BCC structures is enhanced, especially for pure elements and binary compositions, indicating that this rule does not only work effectively for multicomponent systems but also works for low-order systems.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Ab initio simulations on the pure Cr lattice stability at 0K: Verification with the Fe-Cr and Ni-Cr binary systems

Significant discrepancies have been observed and discussed on the lattice stability of Cr between the predictions from the ab initio calculations and the CALPHAD approach. In the current work, we carefully examined the possible structures for pure Cr and reviewed the history back from how Kaufman originally determined the Gibbs energy of FCC-Cr in the 1970s. The reliability of Cr lattice stability derived by the CALPHAD and ab initio approaches was systematically discussed. It is concluded that the Cr lattice stability based on the CALPHAD approach has large uncertainty. Meanwhile, we cannot claim that the ab initio H FCC-Cr is error-free as FCC-Cr is an unstable phase under ambient conditions. The present work shows that the ab initio HFCC-Cr can be a viable scientific approach. As both approaches have their limitations, the present work propose to integrate the ab initio results into the CALPHAD platform for the development of the next generation CALPHAD database. As a result, the Fe-Cr and Ni-Cr binary systems were chosen as two case studies demonstrating the capability to adopt the ab initio Cr lattice stability directly into the current CALPHAD database framework.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗

DOE OSTI2020

The Novel Hybrid Ab Initio Model of High-Performance Structural Alloys Design for Fossil Energy Power Plants

The current project developed a novel HT-CALPHAD/DFT approach, which can quickly design new high-performance structural alloys for the application of FE power plants. The PI will mainly take charge of high-throughput DFT simulations and computational thermodynamics of the selected multicomponent alloy systems for the FE power plant applications. At the end of the project, a novel hybrid model based on high throughput CALPHAD/DFT simulations and computational thermodynamics will be developed to provide guidance on how to identify multi-component new high-performance structural alloys with much less computational effort needed. It will address the extensive computation time needed for DFT on the new alloys design. In addition, it will also address the well-known headache of DFT, i.e. how to make the accurate prediction of the high-temperature equilibria. The novel hybrid model the PI proposed will not only be applied to the design of high-performance structural alloys in FE power plants but in many different applications, such as nuclear reactors. This hybrid modeling approach includes four sections: 1) HT-CALPHAD modeling of Al-Co-Cr-Ni-Fe system with FCC and BCC phase. In this section, 3561 non-equiatomic compositions were randomly generated in order to investigate the phase stability of single FCC and BCC phases. Meanwhile, we proposed a data screening procedure to screen out the good candidates within these compositions, considering the temperature range, average density, and melting temperature, etc. 2) Investigation of FCC-Cr lattice stability in Fe-Cr system. We systematically assessed the reliability of FCC-Cr lattice stability derived by DFT and CALPHAD approaches. Meanwhile, the Fe-Cr binary system was chosen as a case study to verify the Cr lattice stability obtained by both approaches. 3) High-throughput DFT modeling on elastic properties of Al-Co-Cr-Ni-Fe systems. We predicted and established the FCC quinary elastic constant database of the Al-Co-Cr-Fe-Ni systems at 0K by using special quasi-random structure (SQS) approach. The predictions will start with pure elements of Al-Co-Cr-Fe-Ni system and will be continued with binaries, ternaries, quaternaries, and finally the quinary compositions. 3) Modeling of temperature-dependent elastic properties in Al-Co-Cr-Ni-Fe systems. In this part, we predict the thermal expansion coefficient and elastic stiffness coefficient as a function of temperature by applying quasiharmonic approximation. With this approach, the elastic properties of HEAs at elevate temperature can be estimated.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2020

Revisit the VEC rule in high entropy alloys (HEAs) with high-throughput CALPHAD approach and its applications for material design-A case study with Al–Co–Cr–Fe–Ni system

Valence electron concentration (VEC) was treated as a useful parameter to predict solid solution phases, and the VEC rule was proposed for high entropy alloys (HEAs). However, this empirical rule has its limitations, which restricts its applications for phase predictions in HEAs. In this paper, we revisited the empirical VEC rule with the HT-CALPHAD approach in the Al–Co–Cr–Fe–Ni system. Our investigation showed that more than 90% compositions are observed to have BCC structures when 5.7≤VEC≤7.2 and we got 100% FCC structures when VEC≥8.4. Meanwhile, we proposed a data screening procedure to classify and discover the new HEAs. The concepts of average density (ρHEA), highest BCC/FCC temperatures ($T$ $^{max}_{BCC/FCC}$), and temperature ranges (ΔT BCC/FCC ) were introduced as useful data screening criteria to down-screen the candidate alloy compositions for specific engineering applications. In the current work, we have identified three HEA categories (refractory BCC HEAs, light-weight BCC HEA and refractory FCC HEAs) in the Al–Co–Cr–Fe–Ni system and proposed the best candidate in each group. Here, our investigation showed the HEA non-equiatomic composition space provides ample opportunities for the discovery of the next-generation HEAs.

36 MATERIALS SCIENCE↗