Engineering topics

Yang, Songge [Worcester Polytechnic Institute, MA (United States)]

Publications and source records attributed to Yang, Songge [Worcester Polytechnic Institute, MA (United States)].

3 records

DOE OSTI2025

Hybrid Doping Strategy with High‐Entropy Cu/Fe Surface Modification and Zr Bulk Incorporation for Ni‐Rich Cathodes

A hybrid doping strategy combining Zr 4+ bulk doping with high-entropy Cu 2+ /Fe 3+ surface doping is developed to enhance the structural and interfacial stability of Ni-rich layered oxide cathodes. Cu and Fe are selectively introduced at the particle surface via a surface-selective ion-exchange process, forming a ≈15 nm Fe-rich layer while preserving the layered framework. Compared to the pristine cathode, the hybrid sample exhibits significantly improved electrochemical performance in both half-cell and full-cell configurations. In half-cells, the hybrid retains 88.5% and 90.2% after 100 cycles at 1C under 4.6 and 4.5 V, respectively. During high-voltage full-cell cycling, the hybrid cathode maintains over 80% capacity retention, whereas the pristine counterpart retains less than 10% under identical conditions over the same cycling period. XPS, EELS, and DEMS analyses confirm improved oxygen retention, suppressed gas evolution, and stable surface chemistry, while DFT calculations indicate enhanced Me–O bonding in the selected Fe 0.75 Cu 0.25 (Mn 1/16 Co 2/16 Ni 13/16 )O 2 surface composition, which is identified through DFT-calculated mixing energy reaching a minimum at this ratio, indicating the most thermodynamically favorable configuration. In conclusion, these results demonstrate the effectiveness of this hybrid doping strategy in mitigating coupled degradation pathways in Ni-rich cathodes.

15 GEOTHERMAL ENERGY↗

DOE OSTI2025

In-situ formation of stable interface towards Li-in anode for halide solid-state electrolyte

Halide-based solid-state electrolytes (SSEs) are promising candidates for next-generation all-solid-state lithium batteries (ASSLBs) due to their high ionic conductivity and chemical stability. However, their poor interfacial compatibility with lithium metal anode and Li-In alloy significantly hinder practical application due to the requirement for a protective interlayer. In this study, a novel approach to overcome this limitation is presented by introducing iron (Fe) doping into Li 3 InCl 6 (LIC), which enables direct and stable contact with lithium-indium (Li-In) metal without a protective interlayer. Thermodynamic and computational analyses identified Fe 3+ as a suitable dopant based on its similar reduction potential to In 3+ and structural compatibility within the halide lattice. The synthesized 10 at. % Fe-doped LIC exhibits high phase purity, retained ionic conductivity, and notably improved interfacial stability. Full-cell tests using Fe-LIC achieve over 300 cycles with 80 % capacity retention. At the same time, symmetric Li-In/ Fe-LIC/ Li-In cells sustain over 500 h of operation, representing the first reported long-term cycling of LIC-based ASSLB without a protective interlayer. In conclusion, this work establishes Fe doping as an effective strategy to stabilize halide SSEs of In system against Li-In alloy, thereby simplifying cell architecture and advancing the development of safer, high-performance halide-based solid-state electrolytes.

Halide-based solid-state electrolytes↗

DOE OSTI2025

Anionic‐Based Layered Oxide Cathodes with High Electrochemical Performance through Dual‐Site Substitutions for Sodium‐Ion Batteries

Mn-rich layered oxide cathodes with anionic redox promise high energy density for sodium-ion batteries (SIBs) due to ultra-high capacity derived from both Mn and O redox couples. Nevertheless, instability of the reactions that lead to poor electrochemical stability hinders the cathodes from practical applications. Here, the Al and Zn dual-site substitution strategy is proposed to enhance electrochemical performance. Here, the designed cathode, Na 0.73 Zn 0.03 Li 0.25 Mn 0.76 Al 0.01 O 2 (AlZn), delivers a high discharge capacity of 242 mAh g −1 with an impressive rate capability (162 mAh g −1 at 1000 mA g −1 ) and excellent capacity retention (89.69% over 150 cycles). In addition, full-cell SIB based on AlZn coupled with hard carbon exhibits a high energy density of 317 Wh kg −1 (based on both cathode and anode mass) and a reasonable capacity retention of 80.8% after 250 cycles. Revealed by advanced investigations, the synergy of robust Al–O in TM layers and O–Zn–O pillars in Na layers helps alleviate severe inactive spinel/rock-salt phase transformation and intragranular cracks in the AlZn cathode. This consequently leads to greatly enhanced electrochemical performance over the pristine cathode. This work provides insight into improving electrochemical properties of anionic-redox-based layered oxides by Al/Zn co-substitutions toward high-energy SIBs.

25 ENERGY STORAGE↗