Yang, X. D. | Search NASA

DOE OSTI2022

Physical mechanisms for the transition from type-III to large ELMs induced by impurity injection on EAST

Transition from type-III to large-amplitude ELMs induced by neon injection has been observed in the EAST tokamak at overlapping q 95 space between large and small ELMs. With neon injection, pedestal density gradient shows a remarkable increase accompanied by some decrease of pedestal electron temperature, and consequently the pressure gradient increases moderately and edge bootstrap current has minimal change. Further experiment demonstrates that the occurrence of large ELMs after neon injection is highly correlated with the change in edge density. Linear peeling-ballooning stability analysis indicates that the large ELM case is more unstable than the type-III ELM case during the ELM transition. A scan of pedestal density gradient in linear stability analysis shows that the direct destabilizing effect of steep pedestal density gradient on peeling-ballooning instabilities via two-fluid effects could also facilitate the transition to large ELMs. In conclusion, these results could provide more insight into the role of pedestal density gradient on pedestal stability and ELM behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

ELECTRON COOLING USING A PULSED AND DITHERING BEAM FROM AN ELECTROSTATIC ELECTRON COOLER

Electron cooling continues to be an invaluable technique to reduce and maintain the emittance in hadron storage rings such as the EIC and EICC where stochastic cooling is inefficient and radiative cooling is negligible. Extending the energy range of electron coolers beyond what is feasible with the conventional, electrostatic approach necessitates the use of RF fields for acceleration and, thus, a bunched electron beam. To experimentally investigate how the relative time structure of the two beams affects the cooling properties, we have set up a pulsed-beam cooling device by adding a synchronized pulsing circuit to the conventional electron source of the CSRm cooler at Institute of Modern Physics. Using both constant and modulated synchronization between electron pulses and ion bunches, we have measured the effects of the electron bunch length and longitudinal ion focusing strength on the temporal evolution of the longitudinal and transverse ion beam profile and demonstrated the detrimental effect of timing jitter as predicted by space-charge theory and simulations. Our experiment suggests a need for further investigations of specific aspects of bunched cooling such as synchro-betatron coupling and phase dithering effects when using short electron bunches to cool longer ion bunches. However, given the comparatively long IBS lifetime of higher-energy proton storage rings like the EIC, slow dithering could potentially provide an option to save cost on the electron cooler linac.

Wang, Haipeng↗

DOE OSTI2021

Simulation of lithium transport using the BOUT++ framework

A numerical model that calculates the collisional interactions between the lithium atoms from a lithium pellet and the background plasmas has been upgraded. The ion density ($N_t$), electron temperature ($T_e$), ion temperature ($T_i$) and parallel ion velocity ($V_{∥, i}$) are used to characterize the background plasmas. The lithium atom density ($N^{a}_{Li}$) and parallel velocity ($V_{∥,a}$) of lithium atoms evolve with time. For each lithium ion, the density ($N_{Li^{n+}}$), temperature ($T_{Li^{n+}}$) and parallel velocity ($V_{∥, Li^{n+}}$) are self-consistently calculated. A C-mod lower single null equilibrium is used to generate the grid for the BOUT++ simulation. The lithium atoms can be fully ionized to $Li^{3+}$ in ~2 μs. The rapid radial and poloidal expansion of the lithium ions are found in the simulation. After the collision interaction process, the electron temperature rapidly decreases at the pellet location; then, it rapidly poloidally expands, and the temperature at the pellet location starts to recover. The electron pressure increases at the pellet location despite the decrease in electron temperature because of the extra electrons from the lithium ionization. The ion pressure profile decreases in the pellet location due to the decrease in ion temperature.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2021

Demonstration of Electron Cooling using a Pulsed Beam from an Electrostatic Electron Cooler

Electron cooling continues to be an invaluable technique to reduce and maintain the emittance in hadron storage rings in cases where stochastic cooling is inefficient and radiative cooling is negligible. Extending the energy range of electron coolers beyond what is feasible with the conventional, electrostatic approach necessitates the use of RF fields for acceleration and, thus, a bunched electron beam. To experimentally investigate how the relative time structure of the two beams affects the cooling properties, we have set up a pulsed-beam cooling device by adding a synchronized pulsing circuit to the conventional electron source of the CSRm cooler at Institute of Modern Physics *. We show the effect of the electron bunch length and longitudinal ion focusing strength on the temporal evolution of the longitudinal and transverse ion beam profile and demonstrate the detrimental effect of timing jitter as predicted by theory and simulations. Compared to actual RF-based coolers, the simplicity and flexibility of our setup will facilitate further investigations of specific aspects of bunched cooling such as synchro-betatron coupling and phase dithering.

Bruker, M. W.↗

DOE OSTI2021

Demonstration of Electron Cooling using a Pulsed Beam from an Electrostatic Electron Cooler

Electron cooling continues to be an invaluable technique to reduce and maintain the emittance in hadron storage rings in cases where stochastic cooling is inefficient and radiative cooling is negligible. Extending the energy range of electron coolers beyond what is feasible with the conventional, electrostatic approach necessitates the use of RF fields for acceleration and, thus, a bunched electron beam. To experimentally investigate how the relative time structure of the two beams affects the cooling properties, we have set up a pulsed-beam cooling device by adding a synchronized pulsing circuit to the conventional electron source of the CSRm cooler at Institute of Modern Physics *. We show the effect of the electron bunch length and longitudinal ion focusing strength on the temporal evolution of the longitudinal and transverse ion beam profile and demonstrate the detrimental effect of timing jitter as predicted by theory and simulations. Compared to actual RF-based coolers, the simplicity and flexibility of our setup will facilitate further investigations of specific aspects of bunched cooling such as synchro-betatron coupling and phase dithering.

Bruker, M. W.↗