Engineering topics

Yang, Zhenzhen

Publications and source records attributed to Yang, Zhenzhen.

At least 19 records

DOE OSTI2026

Direct regeneration of degraded LiFePO4 cathodes via a separator-enabled prelithiation strategy

A persistent challenge in lithium-ion batteries is the loss of active lithium due to the solid electrolyte interphase (SEI) formation and associated side reactions. While prelithiation employing lithium replenishment separator (LRS) has been proven effective in compensating for lithium loss, previous studies have largely been accompanied by gas evolution or solid residue formation during the prelithiation process. To surmount this challenge, we present a LRS based on 4-fluoro-1,2-dihydroxybenzene lithium salt (LiDF), capable of mitigating lithium loss while producing decomposition products that integrate directly into the electrolyte as functional additives which can assist with the stability of the SEI, free from gas or solid formation, thus establishing a sustainable and environmentally benign strategy for lithium compensation. Incorporation of the LRS enables the pristine LiFePO4||graphite (Gr) full cell to achieve 10.8% higher capacity than the cell with a polypropylene separator (PPS) after 200 cycles at 0.5C. Remarkably, the degraded LiFePO4 (D-LFP)||Gr full cell with the LRS exhibits a 135.8% capacity improvement over the PPS-based cell after 500 cycles. These findings establish the LRS as a powerful approach for both boosting high-performance lithium-ion batteries and recovering the capacity of degraded batteries.

Tao, Fujun↗

DOE OSTI2024

High-entropy Li-rich layered oxide cathode for Li-ion batteries

High-entropy oxides (HEOs) are emerging as promising cathode materials for Li-ion batteries (LIBs) due to their stable solid-state phase and compositional flexibility. Herein, we investigate the structural and electrochemical properties of a novel non-equimolar high-entropy cathode material, termed high-entropy Li-rich layered oxide (HE-LLO, Li 1.15 Na 0.05 Ni 0.19 Mn 0.56 Fe 0.02 Mg 0.02 Al 0.02 O 1.97 F 0.03 ), in comparison to a pristine Li-rich layered oxide (PR-LLO, Li1.2Ni0.2Mn0.6O2). The incorporation of multiple cations (Na + , Al 3+ , Mg 2+ , Fe 3+ ) and anion (F - ) into HE-LLO introduces compositional diversity, enhancing structural stability through the entropy stabilization effect. Theoretical calculations confirm a significantly higher configurational entropy in HE-LLO compared to PRLLO, supporting its high-entropy nature. Electrochemical evaluations demonstrate that HE-LLO exhibits considerable capacity retention, preserving 76.8 % of its discharge capacity at 0.5C after 200 cycles, compared to only 36.2 % for PR-LLO. Even under high-temperature conditions, HE-LLO outperformed PR-LLO, maintaining 76.1 % of its discharge capacity after 100 cycles at 5C, while PR-LLO retained only 12.4 %. These enhancements are attributed to the improved phase reversibility and higher Li + ion diffusion coefficients of HE-LLO, validated by ex-situ characterizations using a synchrotron X-ray technique, along with density functional theory (DFT) calculations. In conclusion, these findings highlight the promise of non-equimolar HEOs as a novel design strategy for highperformance cathode materials.

25 ENERGY STORAGE↗

DOE OSTI2024

Multinonmetal-Doped V 2 O 5 Nanocomposites for Lithium-Ion Battery Cathodes

Lithium-ion batteries (LIBs) are critical for portable electronics and electric vehicles, demanding higher energy density to meet increasing energy storage needs. Current commercial cathode materials, such as LiFePO 4 and LiCoO 2 , are limited by a single electron transfer, restricting their energy density. Vanadium pentoxide (V 2 O 5 ) emerges as a promising high-capacity cathode due to its high theoretical capacity of 443 mA h g –1 with three Li storage capacities, significantly surpassing conventional materials. However, the practical application of V 2 O 5 is hindered by a large structural evolution and rapid capacity fading during full lithium intercalation. Here, this study introduces a multinonmetal doping (MNM) strategy to enhance V 2 O 5 cathodes by incorporating all-nonmetal dopants (B, P, and Si) and graphene (G). MNM-V 2 O 5 -G exhibits increased surface oxygen defects, improving charge transfer kinetics and thus enhancing the rate performance and cycling stability. Our results provide valuable insights into the role of surface oxygen defects in stabilizing V 2 O 5 with element doping. This research highlights the potential of multinonmetal doping to improve LIB cathode materials, offering a promising pathway for design of high-energy-density V 2 O 5 cathodes and advancing the development of next-generation energy storage solutions.

25 ENERGY STORAGE↗

DOE OSTI2024

The carbon challenge: Design, synthesis, and chemisorption behavior of solid sorbents in direct air capture of carbon dioxide

Direct air capture (DAC) of CO 2 is a promising solution for reducing the carbon footprint through "negative emission" technology. However, the low CO 2 concentration (~400 ppm) and the dynamic nature of DAC processes present challenges in designing effective sorbent systems. Recent advancements in material design and structural engineering have led to the development of high-performance solid sorbents, offering a more stable, safe, and energy-efficient alternative to traditional liquid CO 2 capture methods. This review highlights progress in solid sorbent-based DAC, focusing on amine-modified materials, hydrogen-bonded frameworks, and ionic liquid-engineered scaffolds. The discussion covers design principles, synthesis methodologies, and their impact on CO 2 chemisorption, comparing the advantages and limitations of each approach. Characterization techniques, especially operando methods and computational tools, are reviewed to understand sorbent behavior during CO 2 integration and release. The reaction pathways and interaction mechanisms of these sorbents with CO 2 are analyzed to guide future design. Additionally, the CO 2 chemisorption behaviors, including capacity, sorption kinetics, recyclability, and durability in the presence of gaseous impurities and under humid conditions will be evaluated and compared. Further, the review offers unique insights into the physical properties, chemical structures, and surface engineering effects of these sorbents, based on comprehensive characterization and evaluation techniques.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Proton-exchange induced reactivity in layered oxides for lithium-ion batteries

LiNi x Co y Mn 1-x-y O 2 (0 < x, y < 1, NCM) is the dominant positive material for the state-of-the-art lithium-ion batteries. However, the sensitivity of NCM materials to moisture makes their manufacturing, storage, transportation, electrode processing and recycling complicated. Although it is recognized that protons play a critical role in their structure stability and performance, proton exchange with Li + in NCM materials has not been well understood. Here, we employ advanced characterizations and computational studies to elucidate how protons intercalate into the layered structure of NCM, leading to the leaching of Li + and the formation of protonated NCM. It is found that protonation facilitates cation rearrangement and formation of impurity phases in NCM, significantly deteriorating structural stability. The adverse effects induced by protons become increasingly pronounced with a higher Ni content in NCM. Through a comprehensive investigation into the thermodynamics and kinetics of protonation, we discover that Li deficiencies in NCM materials can be resolved via solution process in the presence of Li + ions and controlled proton concentration. The underlying mechanism of relithiation is further explored through materials characterizations and kinetics modeling. This work provides crucial insights into controlling structural and compositional defects of Li-ion battery positive material in complicated processing environment.

batteries↗

DOE OSTI2024

Recycled graphite enabled superior performance for lithium ion batteries

Recycling graphite attracts growing attention since cumulative amount of spent Li-ion batteries and the shortage of graphite supply chain. Although various recycling methods have been reported, the recycled graphite cannot reach the strict commercial standards of purity, scalability, efficiency, and capacity, preventing it from battery manufacturing. Herein, the important roles of defects and functional groups on the graphite surface are deeply studied, and a closed-loop graphite recycling process with the surface recovery and modification for the graphite from the end-of-life batteries is demonstrated. The recovered graphite delivers a purity of over 99.9 % and an average initial coulombic efficiency of 91.5 %. Compared with commercial graphite in industrial standard battery testing parameters, full cells with recovered graphite possess enhanced rate reversibility, doubled cycle life, over 10 % higher capacity along with half anode material cost. In conclusion, these impressive results not only underscore the transformative potential of surface reconstruction and modification in graphite recycling, but also present economic feasibility and sustainable pathway for significantly improving battery performance and addressing global resource challenges via integration with the hydrometallurgical recycling process.

25 ENERGY STORAGE↗

DOE OSTI2024

Cascade CO 2 Insertion in Carbanion Ionic Liquids Driven by Structure Rearrangement

The CO 2 chemisorption in state-of-the-art sorbents based on oxide/hydroxide/amine moieties is driven by strong chemical bonding formation in the carbonate/bicarbonate/carbamate products, which in turn leads to high energy input in sorbent regeneration. In addition, the CO 2 uptake capacity was limited by the active sites’ utilization efficiency, with each active site incorporating one CO 2 molecule or less. In this work, a new concept and generation of sorbent was developed to achieve cascade insertion of multiple CO 2 molecules by leveraging structure rearrangement as the driving force, leading to in situ generation of extra CO 2 -binding sites and significantly reduced energy input for CO 2 release. The designed ionic liquids (ILs) containing carbanions with conjugated and asymmetric structure, deprotonated (methylsulfonyl)acetonitrile ([MSA]) anion, allowed the cascade insertion of two CO 2 molecules via consecutive C–C and O–C bond formations. The proton transfer and structure rearrangement of the carboxylic acid intermediates played critical roles in stabilizing the first integrated CO 2 and generating extra electron-rich oxygen sites for the insertion of the second CO 2 . The structure variation and reaction pathway were confirmed by operando spectroscopy, magnetic resonance spectroscopy (NMR), mass spectroscopy, and computational chemistry. The energy input in sorbent regeneration could be further reduced by harnessing the phase-changing behavior of the carbanion salts in ether solutions upon reacting with CO 2 , avoiding the energy consumption in heating the solvent. In conclusion, the fundamental insights obtained herein provide a promising approach to greatly improve the CO 2 sorption performance via sophisticated molecular-scale structural engineering of the sorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Porous liquids: an integrated platform for gas storage and catalysis

Porous liquids (PLs) represent a new frontier in materials design, combining the unique features of fluidity in liquids and permanent porosity in solids. By engineering well-defined pores into liquids via designed structure modification techniques, the greatly improved free volume significantly enhances the gas transport and storage capability of PL sorbents. Triggered by the promising applications of PLs in gas separation, PLs are further explored in catalysis particularly to integrate the gas storage and catalytic transformation procedure. This emerging field has demonstrated promising progress to advance catalytic procedures using PLs as catalysts, with performance surpassing that of the pure liquid and porous host counterparts. In this perspective article, the recent discoveries and progress in the field of integrated gas storage and catalysis by leveraging the PL platforms will be summarized, particularly compared with the traditional homogeneous or heterogeneous catalytic procedures. The unique features of PLs endow them with combined merits from liquid and solid catalysts and beyond which will be illustrated first. This will be followed by the unique techniques being utilized to probe the porosity and active sites in PLs and the structural evolution during the catalytic procedures. The catalytic application of PLs will be divided by the reaction categories, including CO 2 -involving transformation, O 2 -involving reaction, H 2 S conversion, hydrogenation reaction, and non-gas involving cascade reactions. In each reaction type, the synthesis approaches and structure engineering techniques of PLs, structure characterization, catalytic performance evaluation, and reaction mechanism exploration will be discussed, highlighting the structure–performance relationship and the advancement benefiting from the unique features of PLs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

High‐Energy LiNiO 2 Li Metal Batteries Enabled by Hybrid Electrolyte Consisting of Ionic Liquid and Weakly Solvating Fluorinated Ether

Abstract In pursuit of the highest possible energy density, researchers shift their focus to the ultimate anode material, lithium metal (Li 0 ), and high‐capacity cathode materials with high nickel content (Ni > 80%). The combination of these aggressive electrodes presents unprecedented challenges to the electrolyte. Here, we report a hybrid electrolyte consisting of a highly fluorinated ionic liquid and a weakly solvating fluorinated ether, whose hybridization structure enables the reversible operation of a battery chemistry based on Li 0 and LiNiO 2 (Ni = 100%), delivering nearly theoretical capacity of the latter (up to 249 mAh g −1 ) for >300 cycles with retention of 78.6% and in absence of unwanted morphological changes in both electrodes. Extensive characterization assisted by molecular dynamic simulation and density functional theory calculations reveals the function of the fluorinated ether to be far more profound than simple dilution and viscosity reduction. Instead, it induces drastic changes in Li + ‐solvation environment, the consequence of which engenders simultaneous stabilization of electrode/electrolyte and interfacing via formation of respective interfacial chemistries. This study further unlocks fundamental knowledge underneath the prevailing “diluent strategy” that is extensively applied by the electrolyte researchers and opens more design space for the next‐generation electrolytes and interphases for these coveted battery chemistries.

25 ENERGY STORAGE↗

DOE OSTI2024

Polysulfide-incompatible additive suppresses spatial reaction heterogeneity of Li-S batteries

Rational electrolyte engineering for practical pouch cells remains elusive because the correlation between the cathode/solid-electrolyte interphase layer and cell-level reaction behavior is poorly understood. Here, by combining multiscale characterization and computational modeling, we show that—counter to the conventional perception of polysulfide-incompatible additives—the spontaneous reaction of sparingly solvated polysulfides with Lewis acid additives (LAAs) can induce in situ formation of a homogeneous interphase on thick and tortuous S cathode. Multiscale synchrotron X-ray characterization consistently affirms that such interface design could effectively eliminate the notorious problems of polysulfide shuttle and lithium corrosion and, more importantly, provide an interconnected “ion transport highway” to alleviate the uneven ion transport within the tortuous S cathode. Hence, this design dramatically reduces the reaction heterogeneity of lithium-sulfur (Li-S) pouch cells under lean electrolyte conditions. Further, this work resolves controversy around the role of polysulfide-incompatible additives in high-energy Li-S pouch cells and highlights the importance of suppressing reaction heterogeneity for practical batteries.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Intermolecular Proton Transfer Enabled Reactive CO 2 Capture by the Malononitrile Anion

Task-specific ionic liquids (ILs) employing carbanions represent a new class of ILs for carbon capture. The deprotonated malononitrile carbanion, [CH(CN) 2 ] - , has shown close to equimolar capacity for reactive CO 2 capture. Although the formation of the [C(CN) 2 COOH] - carboxylic acid was found to be the final product, how the hydrogen atom on the [CH(CN) 2 ] - carbanion transfers to the carboxylate group as a proton has not been fully understood. In this work, we employ density functional theory calculations with an implicit solvation model to investigate the proton transfer mechanisms in forming carboxylic acid from the reaction of the [CH(CN) 2 ] - carbanion with CO 2 . We find that the intramolecular proton-transfer pathway in [CH(CN) 2 COO] - to form [C(CN) 2 COOH] - is unlikely due to the high energy barrier of 152 kJ/mol. Instead, the intermolecular proton transfer pathway between two [CH(CN) 2 COO] - anions is more feasible to form two molecules of [C(CN) 2 COOH] - , with a significantly lower activation energy of 50 kJ/mol. Moreover, the [C(CN) 2 COOH] - dimer is further stabilized by the intermolecular hydrogen bonds of the two –COOH groups in the Z-configuration of the π-conjugated planar geometry. This insight of reactive CO 2 capture enabled by intermolecular proton transfer will be useful in designing novel carbanions and ILs for carbon capture and conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Acid Etching‐Driven Self‐Assembly of Mn‐Shell Inducing Rock‐Salt Phase for Enhanced Single‐Crystal Ni‐Rich Cathodes

With the wide adoption of Li‐ion batteries, Ni‐rich cathode is considered as one of the most promising candidates of cathodes due to its high energy density and low cost. However, stability decreased with increasing Ni content in the Ni‐rich cathode. To solve this bottleneck, many strategies, such as coating, doping, surface modification, and special morphologies, have been developed. Herein, we introduce a groundbreaking approach for enhancing Ni‐rich cathode through an innovative acid etching process that promotes Mn shell self‐assembly, inducing a rock‐salt phase on the surface. This method not only simplifies the Ni‐rich cathode modification process, but also significantly improves the structural stability and electrochemical performance of Ni‐rich cathode. Our findings demonstrate that developed single‐crystal Ni‐rich cathode shows 3–34 % better stability compared to both commercial modified Ni‐rich cathode and unmodified counterparts. The unique Mn shell effectively mitigates reversible phase shifts during cycling, contributing to a remarkable enhancement in cycling stability. Additionally, this novel fabrication technique paves the way for cost‐effective production of high‐performance cathode materials, offering substantial benefits for lithium‐ion battery technology. And this study proves the potential of this method in advancing the design and development of durable, high‐capacity cathode materials for next‐generation batteries.

Ni-rich cathode↗

DOE OSTI2024

Tailoring the Gating Effect of Organic Cage via a Porous Liquid Approach

Porous liquids (PLs) represent a new frontier in material design combining the merits of solid porous host and liquid phase in gas separation and catalysis. Herein, the PL construction approach is harnessed to tailor the gating effect of organic cages toward enhanced gas separation. A type-II fluorinated PL (F-PL) is developed via liquifying a fluorinated organic cage (F-cage) by a fluorinated ionic liquid (F-IL). The F-cage is featured by a small window size (≈5.1 Å), high surface area, good stability under highly ionic conditions, and abundant fluorine moieties. The F-IL possesses high steric hindrance (bulky cation) and structure similarity with the F-cage (fluorinated alkyl chain in the anion). The existing status structure integrity of F-cage in F-IL upon F-PL formation is illustrated via spectroscopy and X-ray-based techniques. The existence of rigid voids in F-PL is illustrated by positron annihilation lifetime spectroscopy (PALS) and the improved gas uptake capacity than F-IL via pressure-swing CO 2 uptake isotherms (0–40) bar. Further, the comparison of the gas uptake behavior (CO 2 , N 2 , CH 4 , and Xe) of F-PL and F-cage, combining the computational simulation, highlights that the PL construction can be leveraged to tune the window size of porous scaffolds, leading to enhanced gas selectivity.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Precision Structure Engineering of High-Entropy Oxides under Ambient Conditions

High-entropy oxides (HEOs) have unveiled a unique frontier in the realm of heterogeneous catalysis, taking advantage of the entropic effect and increased complexities to deliver ultrahigh stability and large tuning capability. However, current HEO synthesis mainly relies on high-temperature annealing approaches affording HEOs possessing no or low surface area, inferior active site exposure efficiency, and low controllability over the structure tuning. The grand challenge lies in producing high-quality HEO catalysts with high active site utilization efficiency, which relies on precision structure engineering, preferably under mild conditions. In this work, an in situ lattice engineering approach was developed to afford a supported HEO catalyst under ambient conditions. The HEO compositions (CuCoFeNiMnO x ) were uniformly integrated into the lattice of CeO 2 driven by cavitation-induced nucleation being generated via ultrasonication. The as-afforded catalysts were featured by high surface area, atomically dispersed HEO compositions, active redox properties, abundant oxygen vacancies (O V ), antiagglomeration, and high phase stability under harsh conditions. Compared with the ex situ introduction of HEO on the surface, the in situ method provides dual benefits to maintain the dispersity of HEO via entropic and lattice confinement effects. Engineering the complex HEO within the lattice of fluorite-structured CeO 2 also yields abundant defects (e.g., O V ) and active metal sites with strong reducing properties (e.g., Ce 3+ and Cu + ), which greatly improves the activity of the lattice oxygen and tunability of the adsorption behavior of the guest molecules, especially in the presence of impurities (e.g., water and propane). The catalytic performance of the supported HEO catalyst in oxidative procedures surpasses the pure dense phase HEO as well as the ex situ-generated catalysts. Further, the synthesis approach being developed in this work, together with the fundamental understanding in structure evolution and reaction mechanism, showcases a facile pathway under ambient conditions to generate stable catalysts capable of maintaining structural robustness in high-temperature conditions while delivering enhanced catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Stabilizing Graphite Anode in Electrolytes with Nanoscale Anion Networking for High-Rate Lithium Storage

Graphite is the preferred anode material in commercial lithium-ion batteries (LIBs), but its limited compatibility with various organic molecules restricts the electrolyte solvent options. The primary challenge is solvent co-intercalation with Li ions, leading to graphite layer exfoliation. As a result, electrolyte selection often relies on ethylene carbonate (EC)-based solvents. Here, in this study, we introduce electrolytes featuring a nanoscale anion network ordering that hinders the liquid-phase exfoliation of graphite. This network, formed from concentrated long-chain lithium salts, traps free dioxolane (DOL) molecules, reducing the interactions between graphite particles and solvents during Li intercalation. Our findings reveal a mechanism that stabilizes graphite in otherwise unstable solvents with concentrated salts like LiTFSI, providing key insights for improving LIB performance by addressing electrolyte limitations on graphite anodes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2024

Unveiling the porosity effect of superbase ionic liquid-modified carbon sorbents in CO 2 capture from air

Direct air capture (DAC) of CO 2 represents one of the most promising technologies to achieve negative carbon emissions. In this work, the superbase ionic liquids (ILs)-modified carbon substrates were developed for DAC of CO 2 by harnessing the strong CO 2 binding capability of IL and the ordered porous channels of the carbon supports. Detailed porosity analysis revealed that the IL with an aromatic cation and an oxygenate anion preferred to fill the micropores, and a thin layer was created on the surface of the mesopores. Strong π-π interaction between the IL layer and the carbon surface was disclosed by wide-angle X-ray scattering (WAXS) analysis, leading to enhanced thermal stability of the IL phase. For the same lL coating amount, the DAC of CO 2 evaluation revealed that a larger mesopore size and pore volume in the carbon/IL composite materials led to higher CO 2 uptake capacity by exposing more active sites to integrate CO 2 from diluted sources. Further, the thermodynamic analysis confirmed the critical role of IL coating in providing strong chemisorption sites and significantly improved selectivity to enrich the diluted CO 2 from the air atmosphere. This work provides guidance on leveraging the scaffolds' surface properties and porosities of the scaffolds to optimize DAC of CO 2 behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Electrochemical reactivity and passivation of organic electrolytes at spinel MgCrMnO 4 cathode interfaces for rechargeable high voltage magnesium-ion batteries

Magnesium transition metal oxides such as MgCr 2−x Mn x O 4 are promising high-voltage and high-capacity cathode materials for rechargeable magnesium batteries (RMBs). Understanding and improving the chemical and electrochemical stability of the cathode–electrolyte interface (CEI) has been the primary technical emphasis to enable this category of cathode materials, which has been significantly underexplored. Herein, in this study, we focus on investigating the fundamental mechanism of parasitic reactions at the charged surface of the high-voltage MgCrMnO 4 model cathode with different organic electrolytes. The aim is to reveal the underlying effect of anions and solvents responsible for the passivation behavior of the cathode by using three exemplary anions: [(CF 3 SO 2 ) 2 N] − (TFSI − ), Al[OC(CF 3 ) 3 ] 4 − (TPFA − ), and [CB 11 H 12 ] − (MC) and three solvents: diglyme (G2), triglyme (G3), and 3-methoxypropylamine (MPA). High precision leakage current measurements during potentiostatic hold reveal that the electrolyte solvent chemistry has a more profound impact than anion's on the passivation of the MgCrMnO 4 cathode surface during deintercalation of Mg 2+ . X-ray photoelectron spectroscopy exhibits the differences in CEI composition. Amine solvents like MPA show poor passivation due to a higher degree of solvent decomposition, while the thin and anion-derived CEI in glyme-based electrolytes is directly linked with the better passivation behavior on the cathode. Furthermore, we leverage the knowledge from these findings to modify the electrolyte structure by adding a solvent additive, with the goal of reducing the parasitic reaction.

25 ENERGY STORAGE↗

DOE OSTI2024

Light-induced Kondo-like exciton-spin interaction in neodymium(II) doped hybrid perovskite

Abstract Tuning the properties of a pair of entangled electron and hole in a light-induced exciton is a fundamentally intriguing inquiry for quantum science. Here, using semiconducting hybrid perovskite as an exploratory platform, we discover that Nd 2+ -doped CH 3 NH 3 PbI 3 (MAPbI 3 ) perovskite exhibits a Kondo-like exciton-spin interaction under cryogenic and photoexcitation conditions. The feedback to such interaction between excitons in perovskite and the localized spins in Nd 2+ is observed as notably prolonged carrier lifetimes measured by time-resolved photoluminescence, ~10 times to that of pristine MAPbI 3 without Nd 2+ dopant. From a mechanistic standpoint, such extended charge separation states are the consequence of the trap state enabled by the antiferromagnetic exchange interaction between the light-induced exciton and the localized 4 f spins of the Nd 2+ in the proximity. Importantly, this Kondo-like exciton-spin interaction can be modulated by either increasing Nd 2+ doping concentration that enhances the coupling between the exciton and Nd 2+ 4 f spins as evidenced by elongated carrier lifetime, or by using an external magnetic field that can nullify the spin-dependent exchange interaction therein due to the unified orientations of Nd 2+ spin angular momentum, thereby leading to exciton recombination at the dynamics comparable to pristine MAPbI 3 .

36 MATERIALS SCIENCE↗