Engineering topics
Publications and source records attributed to Yang, Zhenzhen.
Compounds, powders, and cathode active materials that can be used in lithium ion batteries are described herein. Methods of making such compounds, powders, and cathode active materials are described.
Residual impurities such as lithium carbonate and hydroxide are a major concern for accelerating parasitic reactions at the cathode electrolyte interface of lithium-ion batteries. Removal of these lithium-bearing species becomes a necessity for high-performance nickel-rich cathode materials. Instead of directly removing these impurities through washing steps, a wet impregnation process is employed to convert these detrimental surface impurities into beneficial surface coating on nickel-rich cathode materials. Specifically, the pristine cathode material is treated with Al(H 2 PO 4 ) 3 solution to convert undesired compounds into Li 3 PO 4 and AlPO 4 , both of which are considered positive surface coating materials for high-voltage cathodes. It is found that the introduced modification greatly suppresses the interfacial impedance hike and improves the capacity retention of the cathode material after repeating charging/discharging. It is believed that these benefits are realized through the modification of the surface chemistry of the cathode material, which helps to slow down the parasitic reactions and reduce the damage to the cathode material.
Graphite is the major anode material used in commercial lithium-ion batteries (LIBs). However, the sluggish ion-transfer kinetics associated with graphite anodes significantly restrict the operation of LIBs over a wide temperature. This is primarily due to their low reversible capacity and the substantial overpotential exhibited under low-temperature conditions. To address this limitation, we demonstrate herein an approach that involves grafting an electrochemically active lithium benzenesulfonate layer onto a graphite surface through a typical reduction reaction of diazonium cations, followed by ion exchange process. This surface modification reduces the charge transfer resistance of graphite anodes, leading to an excellent reversible capacity of ~150 mAh g –1 at low-temperatures (-20 °C, 0.1C). Electrochemical impedance spectroscopy indicates that both desolvation of the lithium ions outside the graphite, and lithium diffusion within the solid electrolyte interphase and graphite lattice are two crucial rate-limiting steps during the Li (de)lithiation, with the latter dominating during the low-temperature operation. In conclusion, these findings demonstrate a facile method for enhancing the low-temperature performance of graphite through surface modification and provide valuable insights into fundamental understandings that can guide the future design of better -low-temperature graphite anodes.
Covalent triazine frameworks (CTFs) represent one of the most extensively studied organic networks characterized by graphitic π-conjugated structures linked by aza-fused rings, possessing unique features such as compositions of light elements (e.g., C, H, and N), porous architectures abundant heteroatom involvement, and extensively conjugated structures. In addition, the textural and chemical structures of CTFs could be engineered via synthesis control to accommodate diverse applications. CTF materials with notable characteristics, including plentiful (ultra-)micropores, high surface areas, and the presence of CO 2 -philic functional groups involving nitrogen (N), oxygen (O), and fluorine (F), hold great promise as potential candidates for anthropogenic CO 2 capture and sequestration (CCS) applications. However, the conventional high-temperature involved ionothermal procedures and the solution-based coupling pathway only afforded CTF materials in powder form, which is difficult to be processed toward membrane formation. Successful fabrication of CTF-derived membranes will rely on the development of alternative polymerization approaches as well as structural engineering to afford membrane architectures with controllable porosity distribution and active interaction sites with CO 2 benefiting the CO 2 separation procedure. In this Account, a demonstration of the latest progress in the development of CTF-derived membranes was provided. The CTF membranes were mainly synthesized via a superacid (e.g., CF 3 SO 3 H)-promoted sol–gel approach involving the polymerization of aromatic nitrile monomers. The formation of the triazine unit through the trimerization of cyano groups served as the cross-linkers, resulting in the creation of π-conjugated networks alongside the arenes present in the starting materials. The aromatic nitrile monomers with rigid and sterically hindered structures were required to afford CTF membranes with nanoporous architectures. The acidity of the superacid and reactivity of the aromatic monomers played critical roles in the polymerization efficiency. The monomer diversity and synthesis tunability endowed the introduction of CO 2 -philic functionalities (e.g., pyrazole and fluorine) within the CTF skeletons, and integration of ionic moieties was achieved by adopting FSO 3 H with stronger acidity as the catalyst and aromatic nitrile monomers with pyrazine structures. To ensure the successful construction of fluorinated CTF membranes, it is important to avoid any fluorines on the ortho-position of the cyano groups on the benzene ring. Through control over the monomers and reaction conditions, flexible, transparent, and insoluble CTF membranes could be fabricated. The sol–gel method could be further expanded to membrane fabrication through acetyl-to-benzene transformation through synthesis control. The mild oxidation-exfoliation-filtration method was also demonstrated to fabricate substrate-supported CTF membranes. The as-afforded membranes are well characterized to determine the structural features and provide information to study the structure-performance relationship. Here, the application of CTF membranes in CO 2 separation was summarized, focusing on the approaches being developed to enhance CO 2 uptake and separation performance. In addition to utilizing the pristine CTF membranes for gas separation, functionalized carbon molecular sieve membranes could be obtained from the pyrolysis of thermally stable CTF membrane precursors toward efficient CO 2 separation, benefiting from the abundant ultramicropores being created during the pyrolysis/decomposition procedure and involvement of CO 2 -philic functionalities such as fluorine and nitrogen-containing moieties. Based on these achievements, unsolved issues in CTF membrane-related fabrication and applications, including the potential solution approaches, have been proposed to advance the application of CTF membranes.
Redox-active polymers (RAPs) are promising organic electrode materials for affordable and sustainable batteries due to their flexible chemical structures and negligible solubility in the electrolyte. Developing high-dimensional RAPs with porous structures and crosslinkers can further improve their stability and redox capability by reducing the solubility and enhancing reaction kinetics. Further, this work reports two three-dimensional (3D) RAPs as stable organic cathodes in Na-ion batteries (NIBs) and K-ion batteries (KIBs). Carbonyl functional groups are incorporated into the repeating units of the RAPs by the polycondensation of Tetrakis(4-aminophenyl)methane and two different dianhydrides. The RAPs with interconnected 3D extended conjugation structures undergo multi-electron redox reactions and exhibit high performance in both NIBs and KIBs in terms of long cycle life (up to 8000 cycles) and fast charging capability (up to 2 A g -1 ). The results demonstrate that developing 3D RAPs is an effective strategy to achieve high-performance, affordable, and sustainable NIBs and KIBs.
Developing low-voltage carboxylate anode materials is critical for achieving low-cost, high-performance, and sustainable Na-ion batteries (NIBs). However, the structure design rationale and structure-performance correlation for organic carboxylates in NIBs remains elusive. Herein, the spatial effect on the performance of carboxylate anode materials is studied by introducing heteroatoms in the conjugation structure and manipulating the positions of carboxylate groups in the aromatic rings. Planar and twisted organic carboxylates are designed and synthesized to gain insight into the impact of geometric structures to the electrochemical performance of carboxylate anodes in NIBs. Among the carboxylates, disodium 2,2’-bipyridine-5,5’-dicarboxylate (2255-Na) with a planar structure outperforms the others in terms of highest specific capacity (210 mAh g -1 ), longest cycle life (2000 cycles), and best rate capability (up to 5 A g -1 ). Further, the cyclic stability and redox mechanism of 2255-Na in NIBs are exploited by various characterization techniques. Moreover, high-temperature (up to 100 °C) and all-organic batteries based on a 2255-Na anode, a polyaniline (PANI) cathode, and an ether-based electrolyte are achieved and exhibited exceptional electrochemical performance. Therefore, this work demonstrates that designing organic carboxylates with extended planar conjugation structures is an effective strategy to achieve high-performance and sustainable NIBs.
Superbase-derived ionic liquids (SILs) are promising sorbents to tackle the carbon challenge featured by tunable interaction strength with CO 2 via structural engineering, particularly the oxygenate-derived counterparts (e. g., phenolate). However, for the widely deployed phenolate-derived SILs, unsolved stability issues severely limited their applications leading to unfavorable and diminished CO 2 chemisorption performance caused by ylide formation-involved side reactions and the phenolate-quinone transformation via auto-oxidation. Here, in this work, robust pyrazolonate-derived SILs possessing anti-oxidation nature were developed by introducing aza-fused rings in the oxygenate-derived anions, which delivered promising and tunable CO 2 uptake capacity surpassing the phenolate-based SIL via a carbonate formation pathway (O-C bond formation), as illustrated by detailed spectroscopy studies. Further theoretical calculations and experimental comparisons demonstrated the more favorable reaction enthalpy and improved anti-oxidation properties of the pyrazolonate-derived SILs compared with phenolate anions. The achievements being made in this work provides a promising approach to achieve efficient carbon capture by combining the benefits of strong interaction strength of oxygenate species with CO 2 and the stability improvement enabled by aza-fused rings introduction.
The durability of anode-free Li metal batteries is largely limited by the undesired Li plating/stripping irreversibility on the current collector due to the infinite volume change, uncontrollable Li dendrite growth, and continuous parasitic reactions between Li metal and the electrolyte. To address these challenges, the formation of a stable and robust solid electrolyte interphase (SEI) with high ionic conductivity and strong mechanical strength is critical. Here, we developed an advanced electrolyte by introducing LiNO 3 into the localized high concentration electrolyte (LHCE) with lithium bis(fluorosulfonyl)imide (LiFSI) salt, 1,2-dimethoxyethane (DME) solvent, and 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TFTE) diluent to in situ construct a LiF and Li x N y O z co-enriched passivation layer on the Cu current collector. The synergetic effect of high mechanical strength of LiF and high ionic conductivity of Li x N y O z endows the Li metal anode with a high Coulombic efficiency (CE) of 99.35%. In conclusion, in anode-free Li metal pouch cell using LiFePO 4 (LFP) as a cathode holds an exceptionally improved capacity retention under the charging/discharging rate of 1/3 C, demonstrating great promise for developing dendrite-free and safe Li metal batteries.
There are numerous factors that can have an impact on the degradation behavior of batteries, such as the number of recharge cycles or the charge rate. Here, we investigate the influence of operating temperature on the structural degradation of the microstructure in lithium-ion positive electrodes. For that purpose, the microstructure is characterized for cathodes which have been cycled for 200 cycles under 6C (10-minute) charging at different operating temperatures, namely, 20°C, 30°C, 40°C, and 50°C. For each operating condition scanning electron microscopy (SEM) images of cross-sectioned Li x Ni 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) electrodes have been analyzed, to determine structural descriptors such as global particle porosity, crack size/length/width distribution, and porosity and specific surface area distribution of individual particles. Additionally, a stereological method has been deployed to investigate the local particle porosity as a function of distance to the particle center. Results show that particle porosity increases with increasing cycling temperature. Particle porosity is greatest at the particle center and decreases along the particle radius to the exterior. Particle surface area is similar across the four cycling-temperature aging conditions.
The transport of lithium ions in the solid electrolyte interphase (SEI) has been previously accepted to proceed in two steps: a fast pore diffusion through the outer, porous organic layer followed by a slow knock-off or vacancy diffusion in the inner, dense inorganic layer. The second step is believed to be the rate-limiting step during fast-charging. In this study, we have intentionally constructed a thicker SEI (SEI-rich) structure on the surface of monoclinic Nb 2 O 5 (H-Nb 2 O 5 ) by adding LiNO 3 into a conventional ethylene carbonate based electrolyte. The electrochemical performance of two electrodes, one SEI-rich and one with few SEI (SEI-lean), was found to be almost the same, including their fast-charging capability and cycling stability, despite the significant difference in their SEI structure. Importantly, analysis using cryogenic scanning/transmission electron microscopy showed the discrete decoration of individual inorganic particles (e.g., Li 2 O) and amorphous species (LiN x O y /organic components) over the surface of H-Nb 2 O 5 . These discrete inorganic particles are in contradiction to the formation of dense inner inorganic layer, which has been commonly postulated. Based on these findings, we propose a new mechanism for Li ion transport through the SEI: one-step pore diffusion, without the second step slow diffusion. This one-step pore diffusion process provides an extremely fast Li ion transport, and effectively removes the kinetic limitation of Li ion transport in the SEI for fast charging. Finally, these results strongly suggest that the influence of SEI structure on the transport kinetics of lithium ions is much less significant than previously accepted. These results offer a new understanding of possible lithium ion transport pathway within SEI and may have implications for the future designs of fast-charging battery materials.
Here, with the limited resources and high cost of lithium-ion batteries (LIBs) and the ever-increasing market demands, sodium-ion batteries (SIBs) gain much interest due to their economical sustainability, and similar chemistry and manufacturing processes to LIBs. As cathodes play a vital role in determining the energy density of SIBs, Mn-based layered oxides are promising cathodes due to their low cost, environmental friendliness, and high theoretical capacity. However, the main challenge is structural instability upon cycling at high voltage. Herein, Mg is introduced into the P2-type Na 0.62 Ni 0.25 Mn 0.75 O 2 cathode to enhance electrochemical stability. By combining electrochemical testing and material characterizations, it is found that substituting 10 mol% Mg can effectively alleviate the P2–O2 phase transition, Jahn-Teller distortion, and irreversible oxygen redox. Moreover, structural integrity is greatly improved. These lead to enhanced electrochemical performances. With the optimized sample, a remarkable capacity retention of 92% in the half cell after 100 cycles and 95% in the full cell after 170 cycles can be achieved. Altogether, this work provides an alternative way to stabilize P2-type Mn-based layer oxide cathodes, which in turn, put forward the development of this material for the next-generation SIBs.
Parasitic reactions are responsible for continuous performance loss during the normal operation and storage of lithium-ion batteries, particularly for those using nickel-rich cathode materials. Among many contributors, residual Li 2 CO 3 on the surface of nickel-rich cathodes plays a detrimental role in promoting parasitic reactions, and hence accelerates the performance loss of those cathode materials. In this work, a wet impregnation process was utilized to convert the detrimental Li 2 CO 3 and LiOH impurities into a beneficial functional surface coating comprising phosphates. Specifically, hydro-phosphates were used as the functional surface modification agents to mitigate the detrimental effect of surface residuals. The best electrochemical performance was achieved by modifying LiNi 0.6 Mn 0.2 Co 0.2 O 2 with a diluted dihydro-phosphate solution (pKa = 7.2), while the metal cation had a negligible impact on the electrochemical performance. This work provides a cheap and simple method for enabling the high performance of nickel-rich cathodes.
Compounds, particles, and cathode active materials that can be used in lithium ion batteries are described herein. Methods of making such compounds, powders, and cathode active materials are described.
Strong binders can be counterproductive for silicon anodes. Here, we show that stresses from cycling Si-based electrodes can cause permanent stretching and wrinkling of the current collector. Furthermore, this deformation damages the electrode coating and accelerates cell aging due to the inactivation of Si domains and facilitation of Li plating. Interestingly, we demonstrate that the formation of wrinkles is size-dependent, being present in pouch cells but absent from coin cells. This size-dependent performance decay indicates that, in extreme cases, testing outcomes are highly dependent on scale and that the validation of battery materials may require testing at larger cell formats.
A cathode active material includes a plurality of cathode active compound particles and a coating disposed over each of the cathode active compound particles. The coating includes a lithium (Li)-ion conducting oxide containing lanthanum (La) and titanium (Ti).
In our initial study on the high-voltage 5 V cobalt-free spinel LiNi 0.5 Mn 1.5 O 4 (LNMO) cathode, we discovered a severe delamination issue in the laminates when cycled at a high upper cut-off voltage (UCV) of 4.95 V, especially when a large cell format was used. This delamination problem prompted us to investigate further by studying the transition metal (TM) dissolution mechanism of cobalt-free LNMO cathodes, and as a comparison, some cobalt-containing lithium nickel manganese cobalt oxides (NMC) cathodes, as the leachates from the soaking experiment might be the culprit for the delamination. Unlike other previous reports, we are interested in the intrinsic stability of the cathode in the presence of a baseline Gen2 electrolyte consisting of 1.2 M of LiPF 6 in ethylene carbonate/ethyl methyl carbonate (EC/EMC), similar to a storage condition. The electrode laminates (transition metal oxides, transition metal oxides, TMOs, coated on an Al current collector with a loading level of around 2.5 mAh/cm 2 ) or the TMO powders (pure commercial quality spinel LNMO, NMC, etc.) were stored in the baseline solution, and the transition metal dissolution was studied through nuclear magnetic resonance, such as 1 H NMR, 19 F NMR, scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS). Significant electrolyte decomposition was observed and could be the cause that leads to the TM dissolution of LNMO. To address this TM dissolution, additives were introduced into the baseline electrolyte, effectively alleviating the issue of TM dissolution. The results suggest that the observed delamination is caused by electrolyte decompositions that lead to etching, and additives such as lithium difluorooxalato borate and p-toluenesulfonyl isocyanate can alleviate this issue by forming a firm cathode electrolyte interface. This study provides a new perspective on cell degradation induced by electrode/electrolyte interactions under storage conditions.
A daunting challenge in the design of lithium ion batteries (LiBs) is enabling 10-min extreme fast charging (XFC) while achieving appreciable charge acceptance and cycle life. This desirable outcome requires both a comprehensive understanding of LiB operation and aging behavior at different length scales and careful optimization. Lithium plating has been a critical bottleneck because, at XFC rates, it consumes cyclable lithium causing distinct aging and safety concerns even in moderate-loading LiBs. Here, we propose combining multiple solutions, including materials-to-electrode design-to-charging protocols, that are intended to overcome limitations in lithium-ion transport in the electrolyte phase, thus enabling 10-min XFC in LiBs. Some implemented strategies include cathode chemistry, optimized carbon binder domain in the cathode, dual layer anode design, improved separator and advanced electrolyte. Further, innovative charging protocols in moderately loading (~3 mAh/cm 2 anode/2.7 mAh/cm 2 cathode) single-layer pouch cells are proposed, together with demonstrated 10-min XFC with higher charge acceptance between 87.3 and 92.1% (or 2–2.1 mAh/cm 2 ) for 600 cycles without lithium plating. This methodical study with well-defined cells shows promise in combining multiple solution strategies to enable 10-min XFC, charting a pathway to achieve XFC in higher-loading energy-optimized LiBs.
Realizing extreme fast charging (XFC) in lithium-ion batteries for electric vehicles is still challenging due to the insufficient lithium-ion transport kinetics, especially in the electrolyte. Herein, a novel high-performance electrolyte (HPE) consisting of lithium bis(fluorosulfonyl)imide (LiFSI), lithium hexafluorophosphate (LiPF 6 ) and carbonates is proposed and tested in pilot-scale, 2-Ah pouch cells. Moreover, the origin of improved electrochemical performance is comprehensively studied via various characterizations, suggesting that the proposed HPE exhibits high ionic conductivity and excellent electrochemical stability at high charging rate of 6-C. Furthermore, the HPE-based pouch cells deliver improved discharge specific capacity and excellent long-term cyclability up to 1500 cycles under XFC conditions, which is superior to the conventional state-of-the-art baseline electrolyte.