Search NASA⌕ Search

Engineering topics

Yang, Zhenzhen

Publications and source records attributed to Yang, Zhenzhen.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A green closed-loop process for selective recycling of lithium from spent lithium-ion batteries

As the economy started to recover from the COVID pandemic, the price of Li 2 CO 3 skyrocketed to its highest. This situation has aggravated concerns about the supply chain for lithium-ion batteries (LIBs). Recycling spent LIBs is a potential solution to alleviate the bottleneck of the supply chain and prevent environmental pollution, and has attracted lots of attention. However, lithium recycling is generally disregarded because of the complex recycling process and its low recycling efficiency. Here, in this work we developed a sustainable lithium recovery process, which can selectively leach and recover lithium with formic acid before recycling valuable metals. With the reported method, lithium can be 99.8% recovered from layered oxide cathode materials with 99.994% purity. In addition, this lithium recovery process is affordable, compared to the typical hydrometallurgical process, by saving 11.15% per kilogram of spent LIBs. Therefore, this research provided a new solution to eliminating the effects of lithium ions on valuable metal separation and the co-precipitation reaction and precluding the influence of other metal ions on lithium recovery. Finally, this simplified lithium recovery process provides new opportunities for sustainable recycling of LIBs and economical restoration of the lithium supply chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Fully Conjugated Poly(phthalocyanine) Scaffolds Derived from a Mechanochemical Approach Towards Enhanced Energy Storage

Phthalocyanines (Pc)-derived materials represent an attractive category of porous organic scaffolds featured by extensive π-conjugated networks, but their construction is still limited to the solution-based pathways, producing materials with inferior conductivity and porosity. Herein, a mechanochemistry-driven approach was developed leveraging the on-surface polymerization of aromatic nitrile monomers with ortho-positioned dicyano groups in the presence of metal catalysts (magnesium, zinc, or aluminum) under neat and ambient conditions. Diverse Pc-functionalized conjugated porous networks (Pc-CPNs) were obtained featured by extensively and fully π-conjugated skeletons, high surface areas, and hierarchical porosities. The monomers in this mechanochemical approach could be extended to those difficult to be handled in solution-based procedures. In this work, the Pc-CPNs displayed attractive electrochemical performance as supercapacitor and anodes in batteries, together with superb long-term stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Enhanced Oxygen Activation Achieved by Robust Single Chromium Atom-Derived Catalysts in Aerobic Oxidative Desulfurization

Oxidative desulfurization (ODS) plays critical roles in the production of high-quality sulfur impurity-free fuels, especially procedures using molecular oxygen as the sole oxidant. However, the state-of-the-art systems still rely on noble metal nanocatalysts, with deactivation issues caused by coking and sintering still present. In this work, leveraging the merits of single-atom catalysts (SACs) with earth-abundant metal cores and robust nanoporous supports, a series of catalysts composed of homogeneously distributed single chromium atoms anchored on multiwalled carbon nanotubes were fabricated and deployed to catalyze the aerobic ODS transformation. Adopting aromatic sulfur compound (ASC)-containing alkanes as a model system with molecular oxygen as the oxidant, efficient oxygen-to-active O 2 •– transformation and subsequent ASCs-to-sulfone conversion have been achieved, with the former benefiting from the chromium-active sites and the latter arising from the robust, nanoporous, and π-conjugated architecture of the supports. The attractive catalytic performance and cycling stability of the chromium-based SACs make them promising candidates in practical sulfur species removal from liquid fuels, supplying an alternative guidance on the catalyst design toward cost-effective and energy-efficient ODS procedures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Synergy of carbonyl and azo chemistries for wide-temperature-range rechargeable aluminum organic batteries

Rechargeable aluminum organic batteries (RAOBs) are promising for developing cost-effective and sustainable energy storage devices due to the low cost, abundance, and high sustainability of aluminum and organic resources. In this study, we designed and synthesized a redox-active polymer bearing carbonyl and azo groups as a cathode material for RAOBs. The polymeric cathode exhibits a high reversible specific capacity, superior cyclic stability, fast charging capability, and a wide operation temperature range (₋40°C to 100°C). X-ray photoelectron spectroscopy (XPS), pair distribution function (PDF) analysis, and soft X-ray absorption near edge structure (XANES) were employed to gain fundamental insight into the carbonyl and azo chemistries in RAOBs, as well as the cathode electrolyte interphase (CEI) structure. We demonstrated a step-by-step alumination/de-alumination reaction for carbonyl and azo groups in the polymer cathode and unraveled a Al 2 O 3⁻ and AlN-rich CEI, which is critical for the impressive performance of RAOBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Mechanochemistry-driven phase transformation of crystalline covalent triazine frameworks assisted by alkaline molten salts

We report covalent triazine frameworks (CTFs) have shown wide applications in the fields of separation, catalysis, energy storage, and beyond. However, it is a long-term challenging subject to fabricate high-quality CTF materials via facile procedures. Herein, a mechanochemistry-driven procedure was developed to achieve phase transformation of crystalline CTFs assisted by alkaline molten salts. The transformation of CTF-1 from staggered AB to eclipsed AA stacking mode was achieved by short time (30 min) mechanochemical treatment in the presence of molten salts composed of LiOH/KOH, generating high-quality CTF-1 material with high crystallinity, high surface area (625 m 2 g -1 ), and permanent/ordered porosity without carbonization under ambient conditions. This facile procedure could be extended to provide nanoporous three-dimensional CTF materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Tuning working potential of silicon-phosphorus anode via microstructure control for high-energy lithium-ion batteries

The primary research on anode materials of lithium-ion batteries have been focused on increasing the specific capacity, while the working potential that is also closely related to the practical energy density of batteries has been paid much less attention. In this paper, starting from micrometer-sized silicon and black phosphorus, we have reported a high-energy silicon-phosphorus/carbon anode (denoted as mSPC) via a high-energy ball milling process, which demonstrates an average discharge working potential of 0.3 volts versus lithium, together with a high reversible capacity of > 2000 mAh/g, high initial coulombic efficiency of 84%, excellent cycle stability, and superior rate capability up to 15 A/g. Furthermore, in situ focused-ion-beam scanning electron microscopy reveals that the volume change of the mSPC anode during repeated (de) lithiation is effectively alleviated. In contrast, starting from nanometer-sized silicon, the resulted anode (denoted as nSPC) not only presents a lower reversible capacity (~1200 mAh/g), but also exhibits a higher charge/discharge working potential, leading to reduced energy density. Our results indicate the importance of composition/structure control in tailoring the working potential and specific capacity of alloying-type anodes towards high-energy lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Achieving low-temperature hydrothermal relithiation by redox mediation for direct recycling of spent lithium-ion battery cathodes

Lithium-ion battery (LIB) recycling is an urgent need to address the massive generation of spent LIBs from portable devices and electrical vehicles. However, the large-scale recycling is hampered by economic and safety issues associated with today's recycling processes. In this study, we demonstrate a safe and energy efficient direct regeneration process based on low-temperature hydrothermal relithiation (LTHR) at low pressure for spent LiNi x Co y Mn z O 2 (0 < x,y,z <1, x + y + z = 1, or NCM) cathode materials. A low concentration of low-cost redox mediator is employed to improve the relithiation kinetics of spent NCM materials, enabling full relithiation temperature to be reduced from 220 °C to 100 °C or below. Correspondingly, the pressure incurred in the relithiation process can be reduced from ~25 bar to 1 bar, offering significantly improved operation safety. Specifically, three NCM materials, including chemically delithiated NCM111, cycled (degraded) NCM111, and cycled NCM622, were successfully regenerated with complete recovery of composition, crystal structure, and electrochemical performance, achieving the same effectiveness as that achieved at high temperature process. Meanwhile, the total energy consumption of spent cell recycling and the greenhouse gas emission is also reduced. This work provides a facile and scalable way to more sustainable LIB recycling with high economic return, high operation safety and low cost.

25 ENERGY STORAGE↗
DOE OSTI2022

Critical Evaluation of Potentiostatic Holds as Accelerated Predictors of Capacity Fade during Calendar Aging

Li-ion batteries will lose both capacity and power over time due to calendar aging caused by slow parasitic processes that consume Li + ions. Studying and mitigating these processes is traditionally an equally slow venture, which is especially taxing for the validation of new active materials and electrolyte additives. Here, we evaluate whether potentiostatic holds can be used to accelerate the diagnosis of Li + loss during calendar aging. The technique is based on the idea that, under the right conditions, the current measured as the cell voltage is held constant can be correlated with the instantaneous rate of side reactions. Thus, in principle, these measurements could capture the rate of capacity fade in real time . In practice, we show that this method is incapable of quantitatively forecasting calendar aging trends. Instead, our study demonstrates that potentiostatic holds can be applied for initial qualitative screening of systems that exhibit promising long-term stability, which can be useful to shrink the parameter space for calendar aging studies. By facilitating the identification of improved formulations, this approach can help accelerate innovation in the battery industry.

25 ENERGY STORAGE↗
DOE OSTI2022

Defect-Regulated Frustrated-Lewis-Pair Behavior of Boron Nitride in Ambient Pressure Hydrogen Activation

We report the construction of heterogeneous frustrated Lewis pairs (FLPs) with performance comparable to or surpassing the homogeneous counterparts in H 2 activation is a long-standing challenge. Herein, sterically hindered Lewis acid (“B” center) and Lewis base (“N” center) sites were anchored within the rigid lattice of highly crystalline hexagonal boron nitride (h-BN) scaffolds. The active sites were created via precision defect regulation during the molten-salt-involved (NaNH 2 and NaBH 4 ) h-BN construction procedure. The as-afforded h-BN scaffolds achieved highly efficient H 2 /D 2 activation and dissociation under ambient pressure via FLP-like behavior, and attractive catalytic efficiency in hydrogenation reactions surpassing the current heterogeneous analogues.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Achieving SEI preformed graphite in flow cell to mitigate initial lithium loss

The irreversible lithium loss due to the formation of solid electrolyte interphase (SEI) in the initial cycle on the graphite anode greatly reduces the overall cell energy density of lithium ion batteries, that is, the lost Li ions from forming SEI lead to the decrease of Li ions for the intercalation. The method of cathode prelithiation has been widely explored to compensate this lithium loss. However, these cathode additives with high lithium contents inevitably lower the loading of the cathode active materials. In this work, we report a novel approach to solve this challenge, a facile graphite prelithiation method by preforming SEI layers on the surface of graphite powders (Pre-SEI graphite) utilizing a specially designed flow cell. The Li accommodation in the graphite anode can be controlled by the operating time and current density in the flow cell for the electrochemical SEI formation. As a result, we demonstrate a 10% initial Columbic efficiency increase of the LiFePO 4 electrode in a full cell configuration using the Pre-SEI graphite, compared with the pristine graphite anode. The electrochemical preformation of SEI on the graphite powders offers a complete solution to offset initial lithium loss without a sacrifice of active cathode material loading.

25 ENERGY STORAGE↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

Abstract The commercialization of lithium–sulfur (Li−S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li stripping/plating reversibility. Herein, we report an effective strategy by combining Se‐doped S hosted in an ordered macroporous framework with a highly fluorinated ether (HFE)‐based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of >5.4 mAh cm −2 with high Coulombic efficiency >99.2 % can be achieved under high areal Se/S loading (5.8 mg cm −2 ), while the underlying mechanism was further revealed through synchrotron X‐ray probes and Time‐of‐Flight Secondary Ion Mass Spectrometry (ToF‐SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (>5.0 mg cm −2 ) and thin Li metal (40 μm).

Zhao, Chen↗
DOE OSTI2022

Ionic liquids for carbon capture

This article covers cutting-edge research in ionic liquid-based materials and their impact on carbon capture. Ionic liquids boast high thermal stability, low vapor pressure, and great tunability. They can be deployed as either sorbents or supported liquid membranes for carbon capture and other gas separations. Absorption of CO 2 in ionic liquids can be achieved via physisorption or chemisorption, depending on the strength of the interaction. For physisorption, both CO 2 -anion and cation–anion interactions are important factors in dictating CO 2 solubility. For chemisorption, the reactivity with CO 2 can be tuned by the basicity of the anion while the stability of the ionic liquid can be enhanced by controlling the cation. Marrying ionicity of ionic liquids with porosity leads to novel porous ionic liquids that feature unique properties for facilitating gas transport, while interfacing ionic liquids with microporous membranes allow the ions to gate the pores for selective gas transport. Further, composite materials of ionic liquids with crystalline materials such as metal–organic frameworks offer scalable heterogeneous interfaces to promote selectivity. Future opportunities include controlling the interaction with CO 2 and its transport at the charged or electrified interface with the ionic-liquid electric double layer, as well as combining CO 2 capture and conversion with ionic liquids.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

The commercialization of lithium-sulfur (Li-S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li striping/platting reversibility. We reported an effective strategy by combining Se-doped S hosted in an ordered macroporous framework with highly fluorinated ether (HFE)-based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of > 5.4 mAh cm -2 with high coulombic efficiency > 99.2% can be achieved under high areal Se/S loading (5.8 mg cm -2 ), while the underlying mechanism was further revealed through synchrotron X-ray probes and Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (> 5.0 mg cm -2 ) and thin Li metal (40 µm).

25 ENERGY STORAGE↗
DOE OSTI2022

A Comprehensive Understanding of the Aging Effects of Extreme Fast Charging on High Ni NMC Cathode

As the battery industry shifts toward high Ni content cathodes, such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 [NMC811], a complete understanding of the degradation mechanisms of NMC811 under extreme fast charging (XFC) (XFC, ≤10–15 min charging) conditions is needed. Such comprehensive understanding would identify the most critical materials gaps that need to be addressed for enabling XFC long-life cells for electric vehicles. This study maps out the key aging mechanisms for NMC811 cycled at different XFC conditions (between 1C and 9C) for up to 1000 cycles. To acquire a fundamental understanding of utilization and degradation, cells are evaluated using a range of electrochemical techniques, and multimodal and multiscale microscopy techniques to quantify chemical, structural, and crystallographic degradation as a function of cycling conditions for the NMC cathode. When comparing NMC811 to NMC532, it is observed that NMC811 has a greater subsurface crystallographic degradation and displays a similar magnitude of subparticle cracking. However, the NMC811 maintains superior performance despite those advanced degradations. Here, the superior cycle life performance is attributed to the NMC811 particles having radially oriented grains and improved transport properties. NMC811 shows between 4.6× and 3.15× reduction in capacity fade than NMC532 for charging rates between 4C (e.g., 15-min charging) and 6C (10-min charging).

25 ENERGY STORAGE↗
DOE OSTI2022

Enabling Non-Carbonate Electrolytes for Silicon Anode Batteries Using Fluoroethylene Carbonate

Silicon is considered as one of the most promising anodes for next generation lithium-ion batteries, due to its high theoretical capacity and energy density. However, many technical barriers remain to its implementation, due to its high chemical/electrochemical reactivities with standard electrolytes and incomplete passivation. In this work, we take the most effective passivating additive of fluoroethylene carbonate (FEC) and study its impact on non-carbonate electrolytes. Our results indicate that esters and ureas-based electrolytes are similarly stabilized by FEC, and have very similar capacity retentions and Coulombic efficiencies to the state-of-the-art carbonate electrolyte. This study indicates the discovery of more efficient additives other than FEC is vital in developing an electrolyte that can successfully enable a silicon-anode battery.

25 ENERGY STORAGE↗