Search NASA⌕ Search

Engineering topics

Yao, B

Publications and source records attributed to Yao, B.

SU-F-J-167: Use of MR for Permanent Prostate Implant Preplanning

Purpose: To study the feasibility using MR imaging to improve target definition on ultrasound during permanent prostate implants and aid in source strength determination for treatment planning in the OR. Methods: Patients who receive permanent prostate implants undergo MR and CT imaging prior to the implant procedure to determine the volume of the prostate, bony restriction to the procedure, bladder extension, external sphincter length and neurovascular bundle. The volume of the prostate is generally used to order seeds for the procedure. In 10 patients, the MR was used as the preplanning study with the PTV defined as a 2 mm expansion of the MR prostate in all directions except the posterior. Various dose volume parameters for the MR prostate and the PTV were compared to the actual preplan developed and executed in the OR. In addition, there parameters were compared to the post implant dosimetry performed 3 weeks after the implant procedure. Results: The results show that the number of seeds used using MR and US (ultrasound) planning was generally with 2 seeds and the maximum difference was 7 seeds. There is no significant difference between any of the dose index parameters of V100, V150, V200, D99 and D90 parameters between MR planning, US planning and postimplant evaluation There was a significant difference between planned D99 (avg of 105%) and achieved D99 (avg 91%). Conclusion: MR imaging is an invaluable tool to improve target definition for permanent prostate implants. Use of MR images for preplanning improves the confidence with which source can be ordered for the procedure that is OR planned. Ordering a maximum of 10 seeds more than planned would be sufficient to deliver a plan in the OR using US. Moving ahead to non-rigid registration between MR ad US images could further increase the confidence level of MR planning.

60 APPLIED LIFE SCIENCES↗

Evidence of cation vacancy induced room temperature ferromagnetism in Li-N codoped ZnO thin films

Room temperature ferromagnetism (RTFM) was observed in Li-N codoped ZnO thin films [ZnO:(Li, N)] fabricated by plasma-assisted molecular beam epitaxy, and p-type ZnO:(Li, N) shows the strongest RTFM. Positron annihilation spectroscopy and low temperature photoluminescence measurements indicate that the RTFM in ZnO:(Li, N) is attributed to the defect complex related to V{sub Zn}, such as V{sub Zn} and Li{sub i}-N{sub O}-V{sub Zn} complex, well supported by first-principles calculations. The incorporation of N{sub O} can stabilize and enhance the RTFM of ZnO:(Li, N) by combining with Li{sub i} to form Li{sub i}-N{sub O} complex, which restrains the compensation of Li{sub i} for V{sub Zn} and makes the ZnO:(Li, N) conduct in p-type.

36 MATERIALS SCIENCE↗

Microstructural Characterization of Burnable Absorber Materials Being Evaluated for Application in LEU U-Mo Fuel Plates

The starting microstructure of a fuel plate will impact how it performs during irradiation. As a result, microstructural characterization has been performed on as-fabricated monolithic fuel plates to determine the changes in fuel plate microstructure that may result from changes in fabrication parameters. Particular focus has been given to the fuel plate U-10Mo/Zr and Zr/AA6061 cladding interfaces, since the integrity of these interfaces will play a big role in determining the overall performance of the fuel plate during irradiation. In addition, burnable absorber materials for potential incorporation into monolithic fuel plates have been characterized to identify their as-fabricated microstructures. This information will be important when trying to understand the PIE data from fuel plates with burnable absorbers that are irradiated in future irradiation experiments. This paper will focus on the microstructures observed using optical metallography, X-ray diffraction, and scanning and transmission electron microscopy for monolithic fuel plates exposed to different fabrication parameters and for as-fabricated burnable absorber materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Structural and electrical characteristics of high quality (100) orientated-Zn{sub 3}N{sub 2} thin films grown by radio-frequency magnetron sputtering

We report on highly crystalline zinc nitride (Zn{sub 3}N{sub 2}) thin films which were grown by rf magnetron sputtering on quartz substrates. The substrate temperature during growth is found to strongly affect the crystal quality of the thin films. The chemical bonding states were determined by x-ray photoelectron spectroscopy. Large chemical shifts in core-level N 1s peaks with binding energy of 396.4 eV were observed as compared to N 1s of free amine (398.8 eV), indicating Zn-N bond formation. Two N 1s states were found: one is N{sub 1} formed by Zn-N bonds and another is (N{sub 2}) produced by substitution of N molecules at N ion sites, which leads to larger lattice constants, consistent with x-ray diffraction results. Temperature-dependent Hall effect measurements of our Zn{sub 3}N{sub 2} films exhibited distinct conduction mechanisms at specific different temperature ranges.

36 MATERIALS SCIENCE↗

Electrical properties and stability of p-type ZnO film enhanced by alloying with S and heavy doping of Cu

Single wurtzite p-type Zn{sub 1-y}Cu{sub y}O{sub 1-x}S{sub x} alloy films with 0.081{<=}x{<=}0.186 and 0.09{<=}y{<=}0.159 were grown on quartz reproducibly by magnetron sputtering. The alloys show very stable p-type conductivity with a hole concentration of 4.31-5.78x10{sup 19} cm{sup -3}, a resistivity of 0.29-0.34 {Omega} cm and a mobility of 0.32-0.49 cm{sup 2} V{sup -1} s{sup -1}. The p-type conductivity is attributed to substitution of Cu{sup +1} for the Zn site, and the ionization energy of the Cu{sup +1} acceptor is measured to be 53 meV, much less than that of Cu-doped ZnO reported previously. The small ionization energy is due to Cu heavy doping and increase in valence band maximum of ZnO induced by alloying with S.

36 MATERIALS SCIENCE↗

Microstructural Analysis of As-Processed U-10 wt% Mo Monolithic Fuel Plate in AA6061 Matrix with Zr Diffusion Barrier

For higher U-loading in low-enriched U-10wt.%Mo fuels, monolithic fuel plate clad in AA6061 is being developed as a part of Reduced Enrichment for Research and Test Reactor (RERTR) program. This paper reports the first characterization results from a monolithic U- 10wt.%Mo fuel plate with a Zr diffusion barrier that was fabricated as part of a plate fabrication campaign for irradiation testing in the Advanced Test Reactor (ATR). Both scanning and transmission electron microscopy (SEM and TEM) were employed for analysis. At the interface between the Zr barrier and U-10wt.%Mo, going from Zr-to-U(Mo), UZr2, ?-UZr, Zr solidsolution and Mo2Zr phases were observed. The interface between AA6061 cladding and Zr barrier plate consisted of four layers, going from Al-to-Zr, (Al,Si)2Zr, (Al,Si)Zr3 (Al,Si)3Zr, and AlSi4Zr5. Irradiation behavior of these intermetallic phases is discussed based on their constituents. Characterization of as-fabricated phase constituents and microstructure would help understand the irradiation behavior of these fuel plates, interpret post-irradiation examination, and optimize the processing parameters of monolithic fuel system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

SEM and TEM Characterization of As-Fabricated U-7Mo Disperson Fuel Plates

The starting microstructure of a dispersion fuel plate can have a dramatic impact on the overall performance of the plate during irradiation. To improve the understanding of the as-fabricated microstructures of dispersion fuel plates, SEM and TEM analysis have been performed on RERTR-9A archive fuel plates, which went through an additional hot isostatic procsssing (HIP) step during fabrication. The fuel plates had depleted U-7Mo fuel particles dispersed in either Al-2Si or 4043 Al alloy matrix. For the characterized samples, it was observed that a large fraction of the ?-phase U-7Mo alloy particles had decomposed during fabrication, and in areas near the fuel/matrix interface where the transformation products were present significant fuel/matrix interaction had occurred. Relatively thin Si-rich interaction layers were also observed around the U-7Mo particles. In the thick interaction layers, (U)(Al,Si)3 and U6Mo4Al43 were identified, and in the thin interaction layers U(Al,Si)3, U3Si3Al2, U3Si5, and USi1.88-type phases were observed. The U3Si3Al2 phase contained some Mo. Based on the results of this work, exposure of dispersion fuel plates to relatively high temperatures during fabrication impacts the overall microstructure, particularly the nature of the interaction layers around the fuel particles. The time and temperature of fabrication should be carefully controlled in order to produce the most uniform Si-rich layers around the U-7Mo particles.

99 GENERAL AND MISCELLANEOUS↗

Interdiffusion in Diffusion Couples: U-Mo v. Al and Al-Si

Interdiffusion and microstructural development in the U-Mo-Al system was examined using solid-tosolid diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo and U-12wt.%Mo vs. pure Al, annealed at 600°C for 24 hours. The influence of Si alloying addition (up to 5 wt.%) in Al on the interdiffusion microstructural development was also examined using solid-to-solid diffusion couples consisting of U-7wt.%Mo, U-10wt.%Mo and U-12wt.%Mo vs. pure Al, Al-2wt.%Si, and Al-5wt.%Si annealed at 550°C up to 20 hours. Scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA) were employed to examine the development of a very fine multiphase intermetallic layer. In ternary U-Mo-Al diffusion couples annealed at 600°C for 24 hours, interdiffusion microstructure varied of finely dispersed UAl3, UAl4, U6Mo4Al43, and UMo2Al20 phases while the average composition throughout the interdiffusion zone remained constant at approximately 80 at.% Al. Interdiffusion microstructure observed by SEM/TEM analyses and diffusion paths drawn from concentration profiles determined by EPMA appear to deviate from the assumption of “local thermodynamic equilibrium,” and suggest that interdiffusion occurs via supersaturated UAl4 followed by equilibrium transformation into UAl3, U6Mo4Al43, UAl4 and UMo2Al20 phases. Similar observation was made for U-Mo vs. Al diffusion couples annealed at 550°C. The addition of Si (up to 5 wt.%) in Al significantly reduced the thickness of the intermetallic layer by changing the constituent phases of the interdiffusion zone developed in U-Mo vs. Al-Si diffusion couples. Specifically, the formation of (U,Mo)(Al,Si)3 with relatively large solubility for Mo and Si, along with UMo2Al20 phases was observed along with disappearance of U6Mo4Al43 and UAl4 phases. Simplified understanding based on U-Al, U-Si, and Mo-Si binary phase diagrams is discussed in the light of the beneficial effect of Si alloying addition.

99 GENERAL AND MISCELLANEOUS↗