Search NASA⌕ Search

Engineering topics

Yates, E. C., Jr.

Publications and source records attributed to Yates, E. C., Jr..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Computation of transonic vortex flows past delta wings Integral equation approach

The steady full-potential equation is written in the form of Poisson's equation, and the solution of the velocity field is expressed in terms of an integral equation. The solution consists of a surface integral of vorticity distribution on the wing and its free-vortex sheets and a volume integral of source distribution within a volume around the wing and its free-vortex sheets. The solution is obtained through successive iteration cycles. The source distribution is computed by using a mixed finite-difference scheme of the Murman-Cole type. The method is applied to delta wings. Numerical examples show that a conical shock is captured on the suction side of the wing. It is attached to the lower surface of the leading-edge vortex but does not necessarily reach to the wing surface.

Kandil, O. A.↗
NASA NTRS1985

Unsteady subsonic and supersonic flows - Historical review; state of the art

This lecture is introductory to the subject of unsteady subsonic and supersonic flows. The primary objective is to present fundamental concepts in order to promote an understanding of the relations between the basic physical problems and their mathematical formulation as well as to establish a common foundation for the more detailed presentations of subsequent lectures in this session. Linearized (small-perturbation) potential flow is emphasized, although needs beyond that limit are indicated. The basic equations, concepts, and procedures common to all the methods are reviewed first, followed by the development, discussion, and status of methods for creating two-dimensional incompressible flow, strip theory, subsonic lifting-surface theory, subsonic/supersonic surface-panel methods, and supersonic lifting-surface theory.

Yates, E. C., Jr.↗
NASA NTRS1985

Unsteady transonic flows - Introduction, current trends, applications

The computational treatment of unsteady transonic flows is discussed, reviewing the historical development and current techniques. The fundamental physical principles are outlined; the governing equations are introduced; three-dimensional linearized and two-dimensional linear-perturbation theories in frequency domain are described in detail; and consideration is given to frequency-domain FEMs and time-domain finite-difference and integral-equation methods. Extensive graphs and diagrams are included.

Yates, E. C., Jr.↗
NASA NTRS1982

Subsonic aerodynamic and flutter characteristics of several wings calculated by the SOUSSA P1.1 panel method

The SOUSSA (steady, oscillatory, and unsteady subsonic and supersonic aerodynamics) program is the computational implementation of a general potential flow analysis (by the Green's function method) that can generate pressure distributions on complete aircraft having arbitrary shapes, motions and deformations. Some applications of the initial release version of this program to several wings in steady and oscillatory motion, including flutter are presented. The results are validated by comparisons with other calculations and experiments. Experiences in using the program as well as some recent improvements are described.

Yates, E. C., Jr.↗
NASA NTRS1982

Steady, Oscillatory, and Unsteady Subsonic and Supersonic Aerodynamics, production version 1.1 (SOUSSA-P1.1). Volume 2: User/programmer manual. Addendum 1: Analytical treatment of wake influence

The influence of the trailing wake at each wing panel center is investigated. The effect of the wake is calculated by analyzing the wake as being subdivided into trailing wake strips. With the improved program there are two optional ways of calculating the wake effect, and the choice is controlled by an added parameter KANW that is part of the input data.

Cunningham, H. J.↗
NASA NTRS1982

Subsonic aerodynamic and flutter characteristics of several wings calculated by the SOUSSA P1.1 panel method

Several applications of the steady, oscillatory, and unsteady subsonic and supersonic aerodynamics (SOUSSA) computer program to wings with steady and oscillatory motion, including flutter, are discussed. The program employs a generalized Green's function to the full, time-dependent potential-flow equation to obtain an integral equation for the velocity potential at any point in a flow, even points on a body or whole bodies in a flow. Aerodynamic calculations are provided for two rectangular wings, a clipped-tip delta wing, and two swept wings with and without a fuselage. The number and distribution of the finite element panels are varied in order to demonstrate the convergence of the results. The results are shown to be close to those of lifting-surface theory, and further applications with bodies having deformities, arbitrary shapes, motions, and deformations are indicated.

Yates, E. C., Jr.↗
NASA NTRS1982

Measured and calculated effects of angle of attack on the transonic flutter of a supercritical wing

The effects of angle of attack between 0 and 4 degrees were studied. The results indicate that increasing angle of attack from zero can produce substantial changes in the transonic flutter characteristics that are favorable or unfavorable depending on Mach number and angle of attack. The bottom of the transonic flutter-boundary 'bucket' is shown to occur at lower Mach number as angle of attack increases. These flutter results correlate well with the effects of Mach number and angle of attack on aerodynamic behavior, especially on the development of transonic flow phenomena. The calculated flutter characteristics are in good agreement with the experimental data at zero angle of attack, but at nonzero angles of attack the experiments show sharply declining and backward-turning transonic flutter boundaries that are not indicated by the calculations. These may be caused by variations in static aeroelastic deformation.

Yates, E. C., Jr.↗
NASA NTRS1981

Prediction of transonic flutter for a supercritical wing by modified strip analysis and comparison with experiment

Use of a supercritical airfoil can adversely affect wing flutter speeds in the transonic range. As adequate theories for three dimensional unsteady transonic flow are not yet available, the modified strip analysis was used to predict the transonic flutter boundary for the supercritical wing. The steady state spanwise distributions of section lift curve slope and aerodynamic center, required as input for the flutter calculations, were obtained from pressure distributions. The calculated flutter boundary is in agreement with experiment in the subsonic range. In the transonic range, a transonic bucket is calculated which closely resembles the experimental one with regard to both shape and depth, but it occurs at about 0.04 Mach number lower than the experimental one.

Yates, E. C., Jr.↗
NASA NTRS1981

Prediction of transonic flutter for a supercritical wing by modified strip analysis and comparison with experiment

The experiments of Farmer, Hanson, and Wynne (1976) showed that use of a supercritical airfoil can adversely affect wing flutter speeds in the transonic range. Inasmuch as adequate theories for three-dimensional unsteady transonic flow are not yet available, the modified strip analysis published by Yates in 1958 has been used to predict the transonic flutter boundary for the supercritical wing tested by Farmer, Hanson, and Wynne. The steady-state spanwise distributions of section lift-curve slope and aerodynamic center, required as input for the flutter calculations, were obtained from pressure distributions measured by Harris (1972). The calculated flutter boundary is in excellent agreement with experiment in the subsonic range. In the transonic range a 'transonic bucket' is calculated which closely resembles the experimental one with regard to both shape and depth, but it occurs at about 0.04 Mach number lower than the experimental one.

Yates, E. C., Jr.↗
NASA NTRS1980

Hybrid vortex method for lifting surfaces with free-vortex flow

A Nonlinear Hybrid Vortex method (NHV-method) has been developed for predicting the aerodynamic characteristics of wings exhibiting leading- and side-edge separations. This method alleviates the drawbacks of the Nonlinear Discrete Vortex method (NDV-method, also known as the multiple line vortex method.) The NHV-method combines continuous-vorticity and vortex-line representations of the wing and its separated free shear layers. Continuous vorticity is used in the near-field calculations, while discrete vortex-lines are used in the far-field calculations. The wing and its free shear layers are divided into quadrilateral vortex panels having second-order vorticity distributions. The aerodynamic boundary conditions and continuity of the vorticity distributions are satisfied at certain nodal points on the vortex panels. An iterative technique is used to satisfy these conditions in order to obtain the vorticity distribution and the wake shape. Distributed and total aerodynamic loads are then calculated.

Kandil, O. A.↗
NASA NTRS1978

Geometry requirements for unsteady aerodynamics in aeroelastic analysis and design

Aircraft geometry requirements for unsteady aerodynamic computations are discussed and differences between requirements for steady and unsteady flow are emphasized within the framework of a general potential-flow aerodynamic formulation. Its implementation in a computer program called SOUSSA (Steady, Oscillatory, and Unsteady Subsonic and Supersonic Aerodynamic is detailed.

Yates, E. C., Jr.↗
NASA NTRS1976

Developments in steady and unsteady aerodynamics for use in aeroelastic analysis and design

A review is given of seven research projects which are aimed at improving the generality, accuracy, and computational efficiency of steady and unsteady aerodynamic theory for use in aeroelastic analysis and design. These projects indicate three major thrusts of current research efforts: (1) more realistic representation of steady and unsteady subsonic and supersonic loads on aircraft configurations of general shape with emphasis on structural-design applications, (2) unsteady aerodynamics for application in active-controls analyses, and (3) unsteady aerodynamics for the frequently critical transonic speed range. The review of each project includes theoretical background, description of capabilities, results of application, current status, and plans for further development and use.

Yates, E. C., Jr.↗
NASA NTRS1975

Design study of structural concepts for an arrow-wing supersonic-cruise aircraft

An analytical study was performed to determine the best structural approach for design of primary wing and fuselage structure of a Mach number 2.7 arrow-wing supersonic cruise aircraft. Concepts were evaluated considering near-term start-of-design. Emphasis was placed on the complex interactions between thermal stress, static aeroelasticity, flutter, fatigue and fail-safe design, static and dynamic loads, and the effects of variations in structural arrangements, concepts and materials on these interactions. Results indicate that a hybrid wing structure incorporating low-profile convex-beaded and honeycomb sandwich surface panels of titanium alloy 6Al-4V were the most efficient. The substructure includes titanium alloy spar caps reinforced with Boron-polyimide composites. The fuselage shell is a closed-hat stiffened skin and frame construction of titanium alloy 6Al-4V. This paper presents an executive summary of the study effort, and includes a discussion of the overall study logic, design philosophy and interaction between the analytical methods for supersonic cruise aircraft design.

Sakata, I. F.↗
NASA NTRS1975

Application of an advanced computerized structural design system to an arrow-wing supersonic cruise aircraft

A structural design study of an arrow-wing supersonic cruise aircraft has been made using the integrated design system, ATLAS, and a relatively large analytical finite-element model containing 8500 degrees of freedom. This paper focuses on structural design methods developed and used in support of the study with emphasis on aeroelasticity. The use of ATLAS permitted (1) automatic resizing of the wing structure for multiple load conditions, (2) rapid evaluation of aeroelastic effects, and (3) an iterative approach to the correction of flutter deficiencies. The significant results of the study are discussed along with the advantages derived from the use of an advanced structural design system in preliminary design studies.

Robinson, J. C.↗
NASA NTRS1974

On repetitive flutter calculations in structural design

The use of continually updated natural modes, called changing modes, is discussed together with the employment of fixed modes in the design process. 'No-derivatives' methods are considered. The flutter solution process is separated into parts which are mode dependent and parts which are mode independent. On the basis of this separation an attempt is made to identify the type of design problems which are suitable for the use of changing modes, and the type of problems which are more suitable for fixed modes. The use of derivative methods is also examined.

Haftka, R. T.↗