Search NASA⌕ Search

Engineering topics

Yin, Wei

Publications and source records attributed to Yin, Wei.

Li–Mn–O Li-rich cation disordered rock-salt cathode materials do not undergo reversible oxygen redox during cycling

An in-depth study of “Li 4 Mn 2 O 5 ”, a nanocomposite of Li 2 O and Li 4-x Mn 2 O 5 with a disordered rock salt structure (LMO), was conducted to determine the origins of the observed anomalously high charge and discharge capacity in lithium cells, which can exceed 350 mA h g -1 . Using soft and hard X-ray absorption spectroscopy (XAS), mapping of resonant inelastic X-ray scattering (mRIXS), and X-ray Raman spectroscopy (XRS), it was determined that electrochemical decomposition of Li 2 O upon charge and reduction of Mn to below 3+ during discharge is responsible for the capacities that are observed, with no evidence of contributions from reversible oxygen redox. Here, the over-reduction is exacerbated when charging limits of 4.5–4.8 V are used due to side reactions between electrolytic solution and the highly oxidized active material. These side reactions result in dissolution of Mn at room temperature and release of oxygen and other gases during initial cycles, which, in turn, cause rapid capacity fading. This is accompanied by evolution of the voltage profile upon cycling towards one that resembles that of manganese oxide spinels. The cycling behavior can be improved somewhat by reducing the upper voltage limit, although this results in a diminishment of the discharge capacities below 200 mA h g -1 . By adding various amounts of spinel LiMn 2 O 4 during synthesis, it was possible to produce LMOs with rock salt structures having significantly improved cycling behavior but still having capacities in excess of 250 mA h g -1 . An optimized modified material also exhibits better rate capability and much less gas evolution during initial cycles than the unmodified LMO. Interestingly, as-made modified materials generally exhibited lower than expected average Mn oxidation states attributable to oxygen loss during the synthesis process, as well as higher capacities than expected based on their manganese contents. The oxygen loss during processing may reduce the activity of the remaining oxygen and account for the lower reactivity of the spinel-modified material.

25 ENERGY STORAGE↗

Structure-Based Design of Dual Bactericidal and Bacteria-Releasing Nanosurfaces

Here, we report synergistic nanostructured surfaces combining bactericidal and bacteria-releasing properties. A polystyrene-block-poly(methyl methacrylate) (PS-block-PMMA) diblock copolymer is used to fabricate vertically oriented cylindrical PS structures (“PS nanopillars”) on silicon substrates. The results demonstrate that the PS nanopillars (with a height of about 10 nm, size of about 50 nm, and spacing of about 70 nm) exhibit highly effective bactericidal and bacteria-releasing properties (“dual properties”) against Escherichia coli for at least 36 h of immersion in an E. coli solution. Interestingly, the PS nanopillars coated with a thin layer (≈3 nm thick) of titanium oxide (TiO 2 ) (“TiO 2 nanopillars”) show much improved dual properties against E. coli (a Gram-negative bacterium) compared to the PS nanopillars. Moreover, the dual properties emerge against Listeria monocytogenes (a Gram-positive bacterium). To understand the mechanisms underlying the multifaceted property of the nanopillars, coarse-grained molecular dynamics (MD) simulations of a lipid bilayer (as a simplified model for E. coli) in contact with a substrate containing hexagonally packed hydrophilic nanopillars were performed. The MD results demonstrate that when the bacterium–substrate interaction is strong, the lipid heads adsorb onto the nanopillar surfaces, conforming the shape of a lipid bilayer to the structure/curvature of nanopillars and generating high stress concentrations within the membrane (i.e., the driving force for rupture) at the edge of the nanopillars. Membrane rupture begins with the formation of pores between nanopillars (i.e., bactericidal activity) and ultimately leads to the membrane withdrawal from the nanopillar surface (i.e., bacteria-releasing activity). In the case of Gram-positive bacteria, the adhesion area to the pillar surface is limited due to the inherent stiffness of the bacteria, creating higher stress concentrations within a bacterial cell wall. In conclusion, the present study provides insight into the mechanism underlying the “adhesion-mediated” multifaceted property of nanosurfaces, which is crucial for the development of next-generation antibacterial surface coatings for relevant medical applications.

36 MATERIALS SCIENCE↗

Tailoring the structure and electrochemical performance of sodium titanate anodes by post-synthesis heating

Sodium titanate anodes synthesized via “chimie-douce” methods generally require a post-synthesis dehydration step. Their crystal structures are sensitive to the heating conditions such as temperature, resulting in distinct sodium storage performance. Herein, using in situ and ex situ high-temperature X-ray diffraction, we studied in detail the structural changes of Na 0.74 Ti 1.815 $\square$ 0.185 O 4 ·1.27H 2 O (NTO) under various heating conditions. Electrochemical characterization revealed that NTOs heated at lower temperatures with layered structures deliver larger capacities than those heated at high temperatures with tunnel structures. Heat treatment at moderate temperatures greatly improves the capacity retention of NTO, especially stabilizing the high voltage processes that are major contributors to the capacity fading, because of the modified crystal structure and surface chemistry. As a result, our findings suggest that post-synthesis heating is a simple and effective strategy to tailor the crystal structure, surface chemistry, and electrochemical properties of sodium titanate anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lepidocrocite Titanate–Graphene Composites for Sodium-Ion Batteries

To overcome electronic transport issues of layered titanates in sodium-ion batteries, we have designed and synthesized composites of lepidocrocite titanates with reduced graphene oxide through a solution-based self-assembly approach. The parent lepidocrocite titanate (K 0.8 [Ti 1.73 Li 0.27 ]O 4 ) was exfoliated by a soft-chemical approach and mechanical shaking. Exfoliated layered titania sheets (LTO) were then combined with reduced graphene oxide (rGO) layers to assemble into composites through flocculation. Countercations (i.e., Mg 2+ ) were used for the self-assembly of negatively charged titania and rGO nanosheets via flocculation. The carbon content in the composites was tuned from 1 to 17% by changing the ratio of titania and rGO sheets in the mixed colloidal suspensions. Electrodes were processed with as-prepared LTO-rGO composites without any carbon additives and tested in sodium half-cell configurations. Mg + -coagulated LTO-rGO composite electrodes deliver higher capacities than electrodes prepared with coagulated titania sheets and 10% acetylene black in sodium half-cells and display good capacity retention after 50 cycles. Electrochemical impedance spectroscopy results indicate lower charge transfer resistance for LTO-14.5%rGO composites than that of coagulated titania sheets with 10% acetylene black. A power law analysis of cells containing the composites indicate a hybrid mechanism consisting of both surface and diffusional processes. A comparison with a similar system, that of dopamine-derived LTO-C heterostructures, reveal significant differences. While capacities showed a strong dependence on carbon content for the dopamine-derived materials, this was not true for the LTO-rGO composites. Instead, the highest capacity was obtained for the 14.5% rGO sample, with a lower value obtained for the 17% rGO sample. A greater proportion of the redox processes were surface rather than diffusional in nature for the LTO-rGO composites as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-scale boron penetration toward stabilizing nickel-rich cathode

Nickel-rich layered oxides LiNi x Co y Mn 1-x-y O 2 (x≥0.8) have been recognized as the preferred cathode materials to develop lithium-ion batteries with high energy density (>300Wh kg -1 ). However, the poor cycling stability and rate capability stemming from intergranular cracks and sluggish kinetics hinder their commercialization. To address such issues, a multi-scale boron penetration strategy is designed and applied on the polycrystalline LiNi 0.83 Co 0.11 Mn 0.06 O 2 particles that are pre-treated with pore construction. The lithium-ion conductive lithium borate in grain gaps functions as the grain binder that can bear the strain/stress from anisotropic contraction/expansion, and provides more pathways for lithium-ion diffusion. As a result, the intergranular cracks are ameliorated and the lithium-ion diffusion kinetics is improved. Moreover, the coating layer separates the sensitive cathode surface and electrolyte, helping to suppress the parasitic reactions and related gas evolution. In addition, the enhanced structural stability is acquired by strong B-O bonds with trace boron doping. As a result, the boron-modified sample with an optimized boron content of 0.5% (B5-NCM) exhibits a higher initial discharge capacity of 205.5mAh g -1 at 0.1C (1C=200mA g -1 ) and improved capacity retention of 81.7% after 100 cycles at 1C. Furthermore, the rate performance is distinctly enhanced by high lithium-ion conductive LBO (175.6mAh g -1 for B5-NCM and 154.6mAh g -1 for B0-NCM at 5C).

25 ENERGY STORAGE↗

Heterostructured Lepidocrocite Titanate-Carbon Nanosheets for Electrochemical Applications

Lepidocrocite-type titanates that reversibly intercalate sodium ions at low potentials (~0.6 V vs Na/Na + ) are promising anode candidates for sodium-ion batteries. However, large amounts of carbon additives are often used to improve their electrical conductivity and overcome poor cycling performance in the electrode composites. To ameliorate electronic transport issues of lepidocrocite titanate (K 0.8 Ti 1.73 Li 0.27 O 4 , KTL) in sodium-ion batteries, we have designed and synthesized heterostructures of exfoliated lepidocrocite-type titanium oxide (LTO) nanosheets with alternating carbon layers via a solution-based self-assembly approach. Positively charged dopamine (Dopa) was used as the carbon precursor and intercalated between negatively charged exfoliated titania nanosheets through electrostatic interaction. Dopa-intercalated LTO was then annealed under argon to form conductive carbon layers between titania sheets. The carbon content in the heterostructures was controlled by modifying the self-assembly conditions (i.e., pH, stirring duration, and Dopa-to-LTO ratio). Electrodes were prepared using carbonized heterostructures (LTO-C) without adding more carbon to the composites and tested in sodium half-cell configurations. Further, higher capacities and improved capacity retention over 250 cycles and lower impedance were observed, as the carbon content of LTO-C heterostructures was increased from 0% (LTO nanosheets) to 30%. These results indicate that the self-assembly approach for 2D heterostructured electrode materials is a promising strategy to overcome electronic transport limitations of layered transition-metal oxides and improve their electrochemical performance for next-generation energy storage applications.

25 ENERGY STORAGE↗

A layered nonstoichiometric lepidocrocite-type sodium titanate anode material for sodium-ion batteries

A lepidocrocite-structured sodium titanate prepared by ion-exchange of a Cs-containing precursor shows promise as an anode material for sodium ion batteries, with a discharge capacity of up to 229 mAh g -1 at an average potential of about 0.6 V vs. Na + /Na. Titanium vacancies in the metal oxide layers provide additional sites for sodium intercalation in addition to interlayer sites, which accounts for the higher capacity compared to other previously reported lepidocrocite-structured titanates. By screening a series of electrolyte formulations and binders, we were able to improve the first-cycle coulombic efficiency to 81.8% and 94.7% respectively using CMC/SBR-based and binder-free electrodes in ether electrolytes. Finally, the electrochemical consequences of short-term air-exposure on the electrodes are also discussed.

25 ENERGY STORAGE↗

Structural evolution at the oxidative and reductive limits in the first electrochemical cycle of Li 1.2 Ni 0.13 Mn 0.54 Co 0.13 O 2

High-energy-density lithium-rich materials are of significant interest for advanced lithium-ion batteries, provided that several roadblocks, such as voltage fade and poor energy efficiency are removed. However, this remains challenging as their functioning mechanisms during first cycle are not fully understood. Here we enlarge the cycling potential window for Li 1.2 Ni 0.13 Mn 0.54 Co 0.13 O 2 electrode, identifying novel structural evolution mechanism involving a structurally-densified single-phase A’ formed under harsh oxidizing conditions throughout the crystallites and not only at the surface, in contrast to previous beliefs. We also recover a majority of first-cycle capacity loss by applying a constant-voltage step on discharge. Using highly reducing conditions we obtain additional capacity via a new low-potential P” phase, which is involved into triggering oxygen redox on charge. Altogether, these results provide deeper insights into the structural-composition evolution of Li 1.2 Ni 0.13 Mn 0.54 Co 0.13 O 2 and will help to find measures to cure voltage fade and improve energy efficiency in this class of material.

25 ENERGY STORAGE↗

High-speed 3D shape measurement using the optimized composite fringe patterns and stereo-assisted structured light system

In this study, we propose a high-speed 3D shape measurement technique based on the optimized composite fringe patterns and stereo-assisted structured light system. Stereo phase unwrapping, as a new-fashioned method for absolute phase retrieval based on the multi-view geometric constraints, can eliminate the phase ambiguities and obtain a continuous phase map without projecting any additional patterns. However, in order to ensure the stability of phase unwrapping, the period of fringe is generally around 20, which limits the accuracy of 3D measurement. To solve this problem, we develop an optimized method for designing the composite pattern, in which the speckle pattern is embedded into the conventional 4-step phase-shifting fringe patterns without compromising the fringe modulation, and thus the phase measurement accuracy. We also present a simple and effective evaluation criterion for the correlation quality of the designed speckle pattern in order to improve the matching accuracy significantly. When the embedded speckle pattern is demodulated, the periodic ambiguities in the wrapped phase can be eliminated by combining the adaptive window image correlation with geometry constraint. Finally, some mismatched regions are further corrected based on the proposed regional diffusion compensation technique (RDC). These proposed techniques constitute a complete computational framework that allows to effectively recover an accurate, unambiguous, and distortion-free 3D point cloud with only 4 projected patterns. Experimental results verify that our method can achieve high-speed, high-accuracy, robust 3D shape measurement with dense (64-period) fringe patterns at 5000 frames per second.

42 ENGINEERING↗

High-speed three-dimensional shape measurement using geometry-constraint-based number-theoretical phase unwrapping

In this study, we propose a high-speed three-dimensional (3-D) shape measurement technique for dynamic scenes using geometry-constraint-based number-theoretical phase unwrapping. As a classical algorithm for temporal phase unwrapping (TPU), the number-theoretical approach is suitable for the binary defocusing fringe projection system since it can retrieve an absolute phase without using low-frequency fringe patterns. However, the conventional number-theoretical TPU approach cannot provide sufficient stability to unwrap a high-frequency phase since it requires the two fringe frequencies to be coprime within the global range of the projector coordinate. In contrast, using low-frequency fringe patterns tends to make phase unwrapping more reliable, but at the expense of the measurement precision. By introducing depth constraint into the traditional number-theoretical TPU, we only need to eliminate the phase ambiguity of each pixel within a small period range defined by the depth range, which means that our method just requires the two fringe frequencies to be coprime within the local period range instead of the conventional global range. Due to the reduction of fringe order candidates and the unambiguous phase range, the reliability of phase unwrapping can be significantly improved compared with the traditional number-theoretical TPU approach even when high-frequency fringe patterns are used. The proposed method has been successfully implemented on a high-frame-rate fringe projection system, achieving high-precision, robust, and absolute 3-D shape measurement at 3333 frames per second.

42 ENGINEERING↗

Effect of cisplatin on the clock genes expression in the liver, heart and kidney

Highlights: • Cisplatin-induced nephrotoxicity showed a circadian rhythm. • Cisplatin altered the clock genes expression in a tissue- and gene-specific manner. • Dbp was consistently suppressed in peripheral tissues after cisplatin treatment. Cisplatin is a platinum-based chemotherapy drug that is widely used to treat various types of malignancies. Although the involvement of circadian clock in cisplatin metabolism and excretion has been reported, the effect of cisplatin on circadian rhythm remains unclear. In the present study, we investigated the effects of cisplatin on clock genes expression in mouse peripheral tissues. Cisplatin induced severe nephrotoxicity, as revealed by the significant increase of blood urea nitrogen and serum creatinine levels. Moreover, cisplatin circadian time-dependently induced p21 expression in the liver, heart and kidney, with the highest increase during the dark phase. In addition, cisplatin altered the clock genes expression in the liver, heart and kidney in a tissue- and gene-specific manner. Interesting, the expression of D site of the albumin promoter binding protein (Dbp), a gene involved in detoxification and drug metabolism, was consistently suppressed in the liver, heart and kidney after cisplatin treatment, implying a role of DBP in the toxicity of cisplatin.

60 APPLIED LIFE SCIENCES↗

Phase shifting algorithms for fringe projection profilometry: A review

The principle of structured light and triangulation is used in a wide range of 3D optical metrology applications, such as mechanical engineering, industrial monitoring, computer vision, and biomedicine. Among a multitude of techniques based on this principle, phase shifting pro lometry (PSP) plays a dominant role due to its high attainable measurement accuracy, spatial resolution, and data density. Over the past few decades, many PSP algorithms have been proposed in the literature in order to achieve higher measurement accuracy, lower pattern count, and/or better robustness to different error sources. Besides, many unconventional PSP codification techniques address the problem of absolute phase recovery with few projected patterns, allowing for high-efficiency measurement of objects containing isolated regions or surface discontinuities. In this paper, we present an overview of these state-of-the-art phase shifting algorithms for implementing 3D surface pro lometry. Typical error sources in phase measure- ment for a phase shifting system are discussed, and corresponding solutions are reviewed. The advantages and drawbacks of different PSP algorithms are also summarized to provide a useful guide to the selection of the most appropriate phase shifting technique for a particular application.

36 MATERIALS SCIENCE↗

Scalable Regression Tree Learning on Hadoop using OpenPlanet

As scientific and engineering domains attempt to effectively analyze the deluge of data arriving from sensors and instruments, machine learning is becoming a key data mining tool to build prediction models. Regression tree is a popular learning model that combines decision trees and linear regression to forecast numerical target variables based on a set of input features. Map Reduce is well suited for addressing such data intensive learning applications, and a proprietary regression tree algorithm, PLANET, using MapReduce has been proposed earlier. In this paper, we describe an open source implement of this algorithm, OpenPlanet, on the Hadoop framework using a hybrid approach. Further, we evaluate the performance of OpenPlanet using realworld datasets from the Smart Power Grid domain to perform energy use forecasting, and propose tuning strategies of Hadoop parameters to improve the performance of the default configuration by 75% for a training dataset of 17 million tuples on a 64-core Hadoop cluster on FutureGrid.

Yin, Wei↗

Adaptive Energy Forecasting and Information Diffusion for Smart Power Grids

Smart Power Grids exemplify an emerging class of Cyber Physical Applications that exhibit dynamic, distributed and data intensive (D3) characteristics along with an always-on paradigm to support operational needs. Smart Grids are an outcome of instrumentation, such as Phasor Measurement Units and Smart Power Meters, that is being deployed across the transmission and distribution network of electric grids. These sensors provide utilities with improved situation awareness on near-realtime electricity usage by individual consumers, and the power quality and stability of the transmission network.

97 MATHEMATICS AND COMPUTING↗

Demo Abstract: Toward Data-driven Demand-Response Optimization in a Campus Microgrid

We describe and demonstrate a prototype software architecture to support data-driven demand response optimization (DR) in the USC campus microgrid, as part of the Los Angeles Smart Grid Demonstration Project. The architecture includes a semantic information repository that integrates diverse data sources to support DR, demand forecasting using scalable machine-learned models, and detection of load curtailment opportunities by matching complex event patterns.

Amam, Saima↗