Search NASA⌕ Search

Engineering topics

Yoo, Chun Sang

Publications and source records attributed to Yoo, Chun Sang.

A numerical study of the diffusive-thermal instability of opposed nonpremixed tubular flames

The diffusive-thermal (D-T) instability of opposed nonpremixed tubular flames near extinction is investigated here using two-dimensional (2-D) direct numerical simulations together with the linear stability analysis. Two different initial conditions (IC), i.e. the perturbed IC and the C-shaped IC are adopted to elucidate the effects of small and large amplitude disturbances on the formation of flame cells, similar to conditions found in linear stability analysis and experiments, respectively. The characteristics of the D-T instability of tubular flames are identified by a critical Damköhler number, Da C , at which the D-T instability first occurs and the corresponding number of flame cells for three different tubular flames with different flame radii. It is found that Da C predicted through linear stability analysis shows good agreement with that obtained from the 2-D simulations performed with two different ICs. The flame cell number, N cell , from the 2-D simulations with the perturbed IC is also found to be equal to an integer close to the maximum wavenumber, k max , obtained from the linear stability analysis. However, N cell from the 2-D simulations with the C-shaped IC is smaller than k max and N cell found from the simulations with the perturbed IC. This is primarily because the strong reaction at the edges of the horseshoe-shaped cellular flame developed from the C-shaped IC is more likely to produce larger flame cells and reduce N cell . It is also found that for cases with the C-shaped IC, once the cellular instability occurs, the number of flame cells remains constant until global extinction occurs by incomplete reaction manifested by small Da. It is also verified through the displacement speed, S d , analysis that the two edges of the horseshoe-shaped cellular flame are stationary and therefore do not merge due to the diffusion–reaction balance at the edges. Moreover, large negative S d is observed at the local extinction points while small positive or negative S d features in the movement of flame cells as they adjust their location and size towards steady state.

42 ENGINEERING↗

Response of flame thickness and propagation speed under intense turbulence in spatially developing lean premixed methane–air jet flames

Direct numerical simulations of three-dimensional spatially-developing turbulent Bunsen flames were performed at three different turbulence intensities. We performed these simulations using a reduced methane–air chemical mechanism which was specifically tailored for the lean premixed conditions simulated here. A planar-jet turbulent Bunsen flame configuration was used in which turbulent preheated methane–air mixture at 0.7 equivalence ratio issued through a central jet and was surrounded by a hot laminar coflow of burned products. The turbulence characteristics at the jet inflow were selected such that combustion occured in the thin reaction zones (TRZ) regime. At the lowest turbulence intensity, the conditions fall on the boundary between the TRZ regime and the corrugated flamelet regime, and progressively moved further into the TRZ regime by increasing the turbulent intensity. The data from the three simulations was analyzed to understand the effect of turbulent stirring on the flame structure and thickness. Furthermore, statistical analysis of the data showed that the thermal preheat layer of the flame was thickened due to the action of turbulence, but the reaction zone was not significantly affected. A global and local analysis of the burning velocity of the flame was performed to compare the different flames. Detailed statistical averages of the flame speed were also obtained to study the spatial dependence of displacement speed and its correlation to strain rate and curvature.

36 MATERIALS SCIENCE↗

Chemical explosive mode analysis for a turbulent lifted ethylene jet flame in highly-heated coflow

The recently developed method of chemical explosive mode (CEM) analysis (CEMA) was extended and employed to identify the detailed structure and stabilization mechanism of a turbulent lifted ethylene jet flame in heated coflowing air, obtained by a 3-D direct numerical simulation (DNS). It is shown that CEM is a critical feature in ignition as well as extinction phenomena, and as such the presence of a CEM can be utilized in general as a marker of explosive, or pre-ignition, mixtures. CEMA was first demonstrated in 0-D reactors including auto-ignition and perfectly stirred reactors, which are typical homogeneous ignition and extinction applications, respectively, and in 1-D premixed laminar flames of ethylene–air. It is then employed to analyze a 2-D spanwise slice extracted from the 3-D DNS data. The flame structure was clearly visualized with CEMA, while it is more difficult to discern from conventional computational diagnostic methods using individual species concentrations or temperature. Auto-ignition is identified as the dominant stabilization mechanism for the present turbulent lifted ethylene jet flame, and the contribution of dominant chemical species and reactions to the local CEM in different flame zones is quantified. A 22-species reduced mechanism with high accuracy for ethylene–air was developed from the detailed University of Southern California (USC) mechanism for the present simulation and analysis.

Energy & Fuels↗

Effect of NO on extinction and re-ignition of vortex-perturbed hydrogen flames

The catalytic effect of nitric oxide (NO) on the dynamics of extinction and re-ignition of a vortex-perturbed non-premixed hydrogen-air flame is studied in a counterflow burner. A diffusion flame is established with counterflowing streams of nitrogen-diluted hydrogen at ambient temperature and air heated to a range of temperatures that brackets the auto-ignition temperature. Localized extinction is induced by impulsively driving a fuel-side toroidal vortex into the steady flame, and the recovery of the extinguished region is monitored by planar laser-induced fluorescence (PLIF) of the hydroxyl radical (OH). The dynamics of flame recovery depend on the air temperature and fuel concentration, and four different recovery modes are identified. These modes involve combinations of edge-flame propagation and the expansion of an auto-ignition kernel that forms within the extinguished region. The addition of a small amount of NO significantly alters the re-ignition process by shifting the balance between chain-termination and chain-propagation reactions to enhance auto-ignition. The ignition enhancement by this catalytic effect causes a shift in the conditions that govern the recovery modes. In addition, the effects of NO concentration and vortex strength on the flame recovery are examined. Direct numerical simulations of the flame-vortex interaction with and without NO doping show how the small amount of OH produced by NO-catalyzed reactions has a significant impact on the development of an auto-ignition kernel. This joint experimental and numerical study provides detailed insight into the interaction between transient flows and ignition processes. (author)

08 HYDROGEN↗

Dynamic stiffness removal for direct numerical simulations

A systematic approach was developed to derive non-stiff reduced mechanisms for direct numerical simulations (DNS) with explicit integration solvers. The stiffness reduction was achieved through on-the-fly elimination of short time-scales induced by two features of fast chemical reactivity, namely quasi-steady-state (QSS) species and partial-equilibrium (PE) reactions. The sparse algebraic equations resulting from QSS and PE approximations were utilized such that the efficiency of the dynamic stiffness reduction is high compared with general methods of time-scale reduction based on Jacobian decomposition. Using the dimension reduction strategies developed in our previous work, a reduced mechanism with 52 species was first derived from a detailed mechanism with 561 species. The reduced mechanism was validated for ignition and extinction applications over the parameter range of equivalence ratio between 0.5 and 1.5, pressure between 10 and 50 atm, and initial temperature between 700 and 1600 K for ignition, and worst-case errors of approximately 30% were observed. The reduced mechanism with dynamic stiffness removal was then applied in homogeneous and 1-D ignition applications, as well as a 2-D direct numerical simulation of ignition with temperature inhomogeneities at constant volume with integration time-steps of 5-10 ns. The integration was numerically stable and good accuracy was achieved. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗