Computational Analysis of the External Aerodynamics of the Unpowered X-57 Mod-III Aircraft
Investigations of the external aerodynamics of the unpowered X-57 using computational fluid dynamics are presented.
Yoo, Seung Y.↗
Engineering topics
Yoo, Seung Y.
Publications and source records attributed to Yoo, Seung Y..
Computational Analysis of the External Aerodynamics of the Unpowered X-57 Mod-III Aircraft
Investigations of the external aerodynamics of the unpowered X-57 Mod-III configuration using computational fluid dynamics are presented. Two different Reynolds-averaged Navier-Stokes flow solvers were used in the analysis: the STAR-CCM+ unstructured solver using polyhedral grid topology, and the Launch Ascent Vehicle Aerodynamics (LAVA) structured curvilinear flow solver using structured overset grid topology. A grid refinement study was conducted and suitable grid resolution was determined by examining the forces and moments of the aircraft. Code-to-code comparison shows that STAR-CCM+ and LAVA are in good agreement both in quantitative values and trends. The angle-of-attack sweep and sideslip-angle sweep were performed. Results indicate that lift coefficients have a sharp drop at stall. At high angle of attack, STAR-CCM+ and LAVA show different flow separation behavior possibly due to differences in the turbulence model. The sideslip-angle sweep results show constant pitching moment from 0° to 15°, then a sharp increase between 15° and 20° sideslip angle.
Yoo, Seung Y.↗
Computation Simulations of Electric Propulsion Aircraft: The X-57 Maxwell
Outline - Introduction: X-57 CFD task overview; Motivation. Part I, Computational simulations without propulsion: Establishing CFD (Computational Fluid Dynamics) Best Practices - Grid generation - Mesh refinement study - Numerical methods - Wind tunnel validation study; Power-Off Aerodynamic Database Results. Part II, Computational simulations with propulsion: Cruise Power-On Database; High-Lift Power-On Database. Summary.
Duensing, Jared C.↗
Establishing Best Practices for X-57 Maxwell CFD Database Generation
The X-57 Maxwell is NASA’s latest electric airplane concept that has been simulated for aerodynamic performance using the structured overset and unstructured grid solvers within the Launch Ascent and Vehicle Aerodynamics (LAVA) solver framework as well as the unstructured polyhedral grid solver in Star-CCM+ for code-to-code comparison. In order to validate the predictions, comparisons were made between the CFD solutions and experimental data collected in the 12-foot Low-Speed Wind Tunnel at NASA Langley Research Center. The simulations are in preparation for the development of a comprehensive aerodynamic database which will assess aircraft performance at a variety of conditions. The findings from these simulations will establish the best practices for mesh resolution, numerical discretization, and turbulence modeling to be used for this database. Preliminary database results have shown that best-practices learned from the initial validation simulations will potentially reduce error in X-57 aerodynamic loads and moments relative to experiment by up to 14%.
Duensing, Jared C.↗
Computational Fluid Dynamics Analysis of the Stall Characteristics of a Wing Designed Based on Prandtl's Mininum Induced Drag
Stall characteristics of a wing designed based on Prandtls minimum induced drag solution using the bending moment as the design constraint is presented. Flow field is resolved using the Reynold-Averaged Navier Stokes solver OVERFLOW, version 2.2l, with fully turbulent flow approximation. The turbulence was resolved using the Spalart-Allmaras turbulence model with rotational and curvature correction. Grid independence study show acceptable grid resolution is achieved. The stall angle-of-attack was predicted at 17.25. CFD analysis show that large separations begins inboard, near the symmetry plane, and exists at stall. However, the separated region remain localized and the flow at the wing tip remain attached.
drag↗
Computational Fluid Dynamics Analysis of the Stall Characteristics of a Wing Designed Based on Prandtl's Minimum Induced Drag
This presentation presents the analysis of stall behavior of a wing based on Prandtl's work on minimum induced drag.
bell shaped wing↗
Computational Fluid Dynamics Analysis of the Stall Characteristics of a Wing Design Based on Prandtl's Minimum Induced Drag
Stall characteristics of a wing whose design was based on Prandtl’s minimum induced drag analysis is presented. Flow field is resolved using RANS CFD (Computational Fluid Dynamics) solver OVERFLOW-2. Both in freestream and in ground effect are analyzed. In addition, effect of low-Mach preconditioner on the stall characteristic is presented. Results show that simulations that lack preconditioner predicts higher stall angle as well as much more benign behavior near the stall angle. Stall analysis in freestream show that flow begins to separate at the inboard region. The flow at the tip remains attached until approximately 19.0 degrees angle of attack.
PRANDTL↗
The NASA High Speed ASE Project: Computational Analyses of a Low-Boom Supersonic Configuration
A summary of NASA's High Speed Aeroservoelasticity (ASE) project is provided with a focus on a low-boom supersonic configuration developed by Lockheed-Martin and referred to as the N+2 configuration. The summary includes details of the computational models developed to date including a linear finite element model (FEM), linear unsteady aerodynamic models, structured and unstructured CFD grids, and discussion of the FEM development including sizing and structural constraints applied to the N+2 configuration. Linear results obtained to date include linear mode shapes and linear flutter boundaries. In addition to the tasks associated with the N+2 configuration, a summary of the work involving the development of AeroPropulsoServoElasticity (APSE) models is also discussed.
Silva, Walter A.↗