Engineering topics
Yoon, Roe-Hoan
Publications and source records attributed to Yoon, Roe-Hoan.
Pilot Scale Testing of the Hydrophobic-Hydrophilic Separation Process to Produce Value-Added Products from Waste Coal
The primary objective of this project was to demonstrate the technical and economic feasibility of using the hydrophobic-hydrophilic separation (HHS) process to produce high-purity, value-added clean coal that could serve as feedstock for specialty carbon products from waste coal. An existing one-skid (i.e., the entire unit fits on a single tractor-trailer) HHS pilot-scale facility was used to process bituminous and anthracite waste coals to produce: 1) a clean coal containing less than 5% ash (super-clean) and 2) another containing less than 1.5% ash (ultra-clean), all of which contain single-digit moistures. Sufficient quantities of these products were to be generated to permit detailed evaluations by potential customers producing or developing new, high-value market applications. In addition, the project included the evaluation of several process improvements to reduce the capital and operating costs for a commercial HHS plant. A final objective was to complete an economic analysis, market-penetration analysis, and technology-gap analysis of the HHS technology and its products.
Solvent recovery from solvent-fine coal slurries by filtration and steam stripping
Dewatering of fine coal is a significant industrial challenge with economic and environmental implications. Due to the lack of suitable dewatering technologies, fine coal particles are often discarded to waste impoundments, leading to substantial loss of valuable natural resources while creating environmental problems. The hydrophobic-hydrophilic separation (HHS) process is a unique solution to this problem. In this process, a recyclable solvent is used to simultaneously remove inorganic impurities (ash) and water from a run-of-mine fine coal slurry. A small amount of recyclable oil (or solvent) is added to a fine coal slurry so that the solvent can spontaneously displace the water from the surface of coal particles. The spent solvent is subsequently recovered and recycled in a closed loop. Here, we report the results obtained using two different solvents, i.e., pentane and hexane, to de-ash and dewater ultrafine coal and recover the spent solvent by filtration, followed by steam stripping. Most of the spent solvent can be recovered during the filtration step at 20 psig N₂ and at a 60 s filtration time. The residual solvent left in the cake was then recovered using steam under different conditions. The results showed that the residual solvent concentration could be reduced to <1,400 ppm after 10 s of steam stripping at 150°C and 15 psig.
Extraction, Separation, and Production of High Purity Rare Earth Elements and Critical Minerals from Coal-Based and Related Resources
The general objectives of this project are to develop concepts for rare earth metal and critical mineral production from coal-based and related (minerals associated with coal) resources and incorporate them into a Technical Research Plan with an associated overall flow sheet. The project team has extensive expertise in market evaluation, mineral separation, leaching, chemical separations, alternative metallothermic reaction technology, electrowinning, and electrorefining that was critical to the success of the proposed project. The project included critical industrial partners needed for project success. The project team has extensive expertise in market evaluation, mineral separation, leaching, chemical separations, alternative reduction technology, electrowinning, and electrorefining as well as appropriate pilot-scale facilities to enable this project. The project encompassed broader opportunities for developing domestic resources of REE/CM materials for a more resilient, diverse, and secure supply chain for REE/CM materials with built-in redundancies and appropriate resource stockpiles. The production of REE/CM materials will help to revitalize and rebuild world-class American manufacturing capacity and the related workforce through new jobs and infrastructure. Furthermore, due to the nature and location of the production sites, economic growth in diverse communities of color and economically distressed areas will be cultivated. Finally, this technology can be applied to reuse and remediate coal waste tailings for REE/CM production.
Rare earth ion-adsorption clays in the presence of iron at basic pH: Adsorption mechanism and extraction method
In this work, the uptake mechanism and influence of iron (Fe) co-adsorption on the binding of rare-earth elements (REEs) on kaolinite have been investigated. REEs and varying concentrations of Fe were co-adsorbed onto kaolinite at pH 10.5. Inductively coupled plasma mass spectrometry (ICP-MS), powder X-ray diffraction (PXRD), and X-ray photoelectron spectroscopy (XPS) were used to characterize how Fe co-adsorption influenced the uptake mechanism of REEs on kaolinite. Elemental analysis by ICP-MS revealed that the REE concentrations on kaolinite were unaffected by the presence of Fe. Crystal structure of kaolinite, determined by PXRD, was not altered after REE and Fe co-adsorption. XPS suggests that the adsorbed Fe is in the form of FeOOH, while the greatly attenuated REE XPS signals upon Fe co-adsorption implies that REEs are encapsulated by Fe species. Based on these results, we conclude that FeOOH layers were formed on top of REEs on the surface of kaolinite. Synthesized REE-Fe-kaolinite samples respond poorly to ion-exchange leaching, indicating that Fe is detrimental to the REE ion-exchange efficiency. The inhibition of ion-exchange REE extraction appears to be due to the passivating FeOOH layers. In contrast to ion-exchange methods, reductive leaching was found to dissolve the FeOOH passivating layers and liberate REEs such that they became available for ion-exchange leaching.
A new method of studying the fundamental mechanisms involved in pigment liberation from recycle papers
Deinking flotation is the most efficient and widely used method of removing ink particles from printed papers to improve the recyclability. A prerequisite for successful deinking flotation is detachment of pigments from paper fibers, a subprocess known as liberation. The degree of liberation is usually determined via hyperwashing tests, which are costly and time consuming. Furthermore, they provide no information on the fundamental mechanisms controlling liberation. In the present work, we developed a new method in which ?-potentials of the particles in a pulp are measured and analyzed. If pigments are not liberated from paper fibers, a frequency distribution plot gives a single peak, while two peaks appear when they are liberated. One can readily determine the degrees of liberation from the peak positions and peak heights. In addition, the ?-potential data can be used to construct disjoining pressure isotherms using the DLVO theory that are useful to better understand the fundamental mechanisms involved and the roles of different reagents used to improve pigment liberation.
Predicting the recovery and grade of a rougher flotation circuit from liberation data
A flotation model has been validated against the survey data obtained from a copper rougher flotation circuit with a circulating load. Here, the model was developed using the hydrophobic force as a kinetic parameter, which made it possible to use the contact angles of the free and composite particles as input parameters so that the model can predict both recoveries and grades. The model also recognizes the role of bubble coarsening in determining the froth phase recoveries and grades. The model predictions are in good agreement with the survey data. The size-by-size recovery curve as predicted from the model shows an optimum particle size range that is consistent with most of the operating data reported in the literature. The model suggests that the upper particle size limit may be determined by the instability of the froth phase rather than the turbulence in the pulp phase of a flotation cell.
Ammonium sulfate leaching of NaOH-treated monazite
Rare earth elements (REEs) can be extracted from monazite under aggressive decomposition and leaching conditions. Much of the waste rocks are removed prior to the extraction process to minimize the costs and waste generation, which is difficult with coal byproducts. The possibility of extracting REEs from low-grade monazite concentrates under relatively mild conditions has been explored to simulate the extraction of REEs from coal byproducts. It has been found that monazite can be decomposed in 10 to 50 % NaOH solutions at 80 °C, with the resulting hydrous oxide being subjected to the ammonium sulfate leaching at pH 4. Further, the ς-potential measurements conducted in the presence of the lixiviant suggest that the NH 4+ ions displace the hydrated Ln 3+ ions from the surface of Ln(OH) 3 (s) by an ion-exchange mechanism, which may be driven by the large differences in the hydration enthalpies between the charged species involved. This approach may be advantageous over acid leaching, including the regeneration of spent lixiviant, lower chemical consumption, and leaching at higher pH.
Fundamental Studies on the Recovery of Rare Earth Elements from Coal and Coal Byproducts (Final Product Report)
The objective of this project was to collect fundamental information that can be used to develop disruptive physical and chemical separation methods that may be used to extract the rare earth elements (REEs) from coal-based feedstocks in a highly efficient, cost-effective, and environmentally benign manner. To meet the stated objective, a set of interrelated fundamental studies have been conducted. The project has been subdivided into three broad areas of tasks as follows, (1) measurement of surface forces in the thin liquid films (TLFs) of water confined between two macroscopic surfaces to establish the optimal conditions for efficiently collecting the ultrafine particles of rare earth minerals (REMs) present in the coal-based feedstocks using the flotation and/or the hydrophobic-hydrophilic separation process(es), (2) identification of the fundamental mechanisms by which REE ions adsorb and desorb on clay minerals present in coal byproducts, and the characterization of the ion-adsorption clays (IACs) present in U.S. coals, and (3) developing methods of extracting the REEs from the REMs and IACs present in US coal byproducts in a cost-effective and sustainable manner.
Development of a Flotation Simulator That Can Predict Grade vs. Recovery Curves from Mineral Liberation Data
Flotation is a kinetic process designed to separate mineral fines by control of hydrophobicity. In general, both the recovery and selectivity of a flotation process increase with contact angle. It is difficult, however, to model flotation kinetics using the thermodynamic parameter. In the present work, we consider flotation as heterocoagulation so that the bubble-particle interactions occurring in the pulp phase of a flotation cell can be modeled using the hydrophobic force as a kinetic parameter that can represent the role of contact angles in flotation. Here, the pulp-phase model developed in this manner has been combined with a froth-phase model developed earlier by considering the effect of particles in film thinning kinetics and bubble coarsening (Park et al, 2018). The combined model has been used to develop a flotation simulator that can be used to construct grade vs. recovery curves from feed characteristics (e.g., mineral liberation and particle size) and various operating parameters. The simulator has been tested successfully against a set of bench-scale continuous flotation test results reported in the literature (dos Santos and Galery, 2018).
Pilot-Scale Testing of an Integrated Circuit for the Extraction of Rare Earth Minerals and Elements from Coal and Coal Byproducts Using Advanced Separation Technologies
The primary objective of this project was to develop and demonstrate an integrated pilot-scale circuitry for recovering high-value rare earth elements (REEs) from coal and coal byproducts. The target performance was to produce a mixed REE product with content of at least two percent by weight on a dry mass basis in a cost-effective and environmentally benign manner. During the first nine months of the project period (Phase 2 Budget Period 2), pilot plant construction was completed including all field site startup activities such as permitting, engineering design, procurement/bidding, unit fabrication, site construction, equipment installation, module assembly, safety training, and circuit shakedown. During the remaining 21 months of project period (Phase 2 Budget Period 3), detailed field-testing activities were performed including feedstock sample collection and preparation, exploratory testing, circuit modification, detailed parametric study, and performance optimization. A detailed techno-economic analysis was performed based on the pilot plant testing findings which provided various scenarios for REE production. The project successfully accomplished the proposed target performance by producing mixed rare earth oxide (REO) with greater than 90% purity by weight in a continuous pilot scale operation from two distinctly different coarse refuse materials (i.e., West Kentucky No. 13 and Fire Clay coal seams), and at least three secondary sources (i.e., heap leach process and naturally formed acid mine drainage system). Project partners included the University of Kentucky, Virginia Tech, West Virginia University, Alliance Coal, Blackhawk Mining, Mineral Refining Company, and Mineral Separation Technologies. The pilot scale test facility was constructed at a former mining complex owned by Alliance Natural Resource Partners (Alliance Coal). The site was rehabilitated to accommodate the equipment installation, construction and fabrication, electrical power requirement, water line management and containment. The process units constructed and installed included X-ray sorting unit, crushing and grinding unit, physical separation unit, acid leaching unit, solvent extraction unit, and wastewater management unit. A rare earth mineral concentration unit was constructed as a standalone unit for flexible operation. A detailed environmental assessment and control plan was carried out to identify and quantify any potential impacts of the pilot-scale processing circuitry on the human and eco-system health and well-being. Corresponding mitigation strategies and control measures were provided. A conceptual flowsheet was developed to effectively remove thorium and uranium from high purity rare earth oxide mix or any potential radionuclide enriched stream. The two distinct feedstock materials were secured from the Blackhawk Mining Complex in eastern Kentucky where the Fire Clay (Hazard No. 4) seam is processed. The West Kentucky No. 13 (Baker) coarse refuse material was collected from an active process stream at an Alliance coal preparation plant located in western Kentucky. Characterization analysis indicated that both of feed materials generated from the two sources contained >300 ppm of TREEs on a dry whole mass basis which met the requirements for a qualified feed stock. The two feedstocks were further upgraded using a dual x-ray sorter to prepare the feed material for hydrometallurgical circuit. Thermal treatment on feed material prior to leaching was found to: 1) improve the leaching recovery of REEs, 2) increase the leaching kinetics, and 3) allow the leaching reaction to occur at lower acidity. Roasting at 600°C was selected as the pre-treatment condition for both West Kentucky No. 13 and Fire Clay coarse refuse material. Over 40% of leaching recovery was achieved by roasting West Kentucky No. 13 material having a top particle size of 3 mm in the pilot scale operation using 1.2M sulfuric acid leaching at 75OC. Initial pilot scale testing involved continuous operation of the pilot plant for 94 hours. The leaching unit was operated at solid-to-liquid ratio of 1 to 10 (w/v) using 0.5M sulfuric acid solution at a temperature of 75°C. The continuous solvent extraction circuit utilized rougher and cleaner units with DEHPA and TBP as the extractants. An innovative stripping circuit was developed to accumulate the REE concentration in the stripping solution to a level above 600 ppm. A bleed stream from the recycled strip solution was treated using oxalic acid precipitation which produced a high grade rare earth oxalate. The oxalate product was roasted to remove the oxalate which produced a rare earth oxide product having a purity greater 90%. Due to high concentrations of contaminant ions in the pregnant leach solution (PLS), a modified flowsheet was developed that involved pre-concentration of the REEs using multiple stages of precipitation and redissolution. The advantage of this process was improved removal of contamination before the downstream purification process and a significant cost reduction relative to the circuit that utilized the solvent extraction process. The modified circuitry included processes involving leaching, multistage precipitation, redissolution, and oxalate precipitation followed by roasting of the oxalate product. The circuit produced a mixed REO that was 92.96% pure from the initial test. A detailed parametric test plan was carried out which involved varying key parameters including solids feed rate, acid flowrate, acid concentration, multistage precipitation pH, redissolution pH, oxalate precipitation dosage and pH. The response variables included REE recovery, contaminant recovery, REO product grade and overall chemical consumption. Test results indicated that the acid-to-solid ratio is the key parameter to leaching efficiency as performance deteriorated with an increase in solids concentration. The optimal pH determined for REE precipitation and redissolution was 6.5 and 2.5, respectively. Additional tests were conducted to further improve the flowsheet. Recirculating a portion of the PLS to the feed of the leach tanks improved the leaching performance by lowering the pH of the leaching system and reducing the contamination recovery by shortening the residence time. Moreover, the removal of Al prior to REE precipitation significantly reduced the oxalic acid consumption in the oxalate precipitation circuit. The modified circuit produced over 90% grade REO by weight from both West Kentucky No. 13 and Fire Clay coarse refuse material in pilot scale continuous test programs. A case analysis model was developed to project the REE and major contaminants concentration in each PLS stream based on the leaching condition, pH cut point, and oxalic acid dosage. A correlation was established using empirical and semi-empirical models. Using the models, chemical consumption required for each stage was predicted based on the projected performance of the hydrometallurgy circuit. After identifying the optimum conditions, validation tests were carried out for the treatment of both West Kentucky No. 13 and Fire Clay coarse refuse materials in the pilot plant. The actual circuit performance and chemical consumptions were very close to the model predictions. Other than the two coarse refuse sources, several secondary feedstocks were also tested in the pilot plant facility. A “heap leach” system was constructed using the coarse refuse material generated from cleaning the West Kentucky No. 13 seam coal. Using the two stage SX rougher and cleaner circuit, a concentrate with a grade >90% REO was produced while recovering >97% of the REEs from the heap leach PLS. Naturally generated acid mine drainage (AMD) from West Kentucky No.13 mine was processed using the multistage precipitation circuit in the pilot plant in a test conducted for a period of 32 hours. The final grade of the mix RE oxide produced from the AMD was 90.84% with an overall circuit recovery of 64%. The primary source of REE was the selective precipitation steps involving iron and aluminum rejection. The hydrophobic-hydrophilic separation (HHS) process was proven to effectively recover coal from fine waste materials. For REM recovery, the HHS process was able to produce concentrates at grades of approximately 1.8% REE on an ash basis; however, recovery values were typically low, <10%, under the optimal conditions determined in the laboratory-scale testing. Staged testing of the pilot-scale HHS process for coal recovery and semi-continuous laboratory testing for REM testing showed that a total concentration ratio of more than 15x was observed for the REM recovery process. A circuit simulation package was developed for REE extraction and purification using a spreadsheet-based platform (Microsoft Excel). The REESim circuit simulation package is configured to track the mass and volume flows of components passing through a series of unit operations specified and configured by the user. The mass rates can then be utilized by the user to determine important performance indicators such as product mass yields, concentrate purity levels, element-by-element recoveries, and so forth. The techno-economic analysis showed that the roasting and leaching operations were the most expensive capital items, each contributing approximately 30% to the total capital cost. One notable contributor to the high production costs was the low REE recovery observed in the pilot scale trials. The product basket price was shown to have a strong influence on the economic viability of the scenarios, with the scandium price being the most significant influencer. Operating cost was shown to be extremely sensitive to REE recovery, REE feed grade, and leaching acid consumption. An analysis of ten different scenarios for a 500 t/h commercial operation revealed that three were economically favorable, producing internal rates of return varying from 27.7% to 33.1% and payback periods of 4 to 5 years. The project successfully developed and demonstrated a process to recover REEs from coal and coal byproducts in a pilot-plant operation which consistently produced over 90% grade REO mix from varies types of feedstocks. Commercialization analysis showed that the technology readiness level successfully achieved TRL 6 at the end of the project and demonstrated the need and the potential for scaling the process to further advance the technologies toward the goal of providing a domestic supply of REEs at a commercial scale.
A study of rare earth ion-adsorption clays: The speciation of rare earth elements on kaolinite at basic pH
Synthesized rare earth ion-adsorption clays (La, Ce, Nd, Dy and Y, ~ 400 ppm each) were prepared from kaolinite at various basic pH in open-air conditions. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma mass spectrometry (ICP-MS) were used to characterize the effect of pH on the adsorption mechanism of rare earth elements (REEs) on kaolinite. The crystal structure of kaolinite by XRD analysis is not altered after REE adsorption, suggesting that REEs are bound to the surface of kaolinite. Elemental analysis by XPS and ICP-MS show that the surface concentration of REEs on kaolinite is pH dependent, and a local maximum of the surface concentration is achieved at pH 10. Three characteristics of the La 3d 5/2 XPS photoemission feature were measured and compared to those of standard La compounds to probe the speciation of REEs, and electrostatically bound hydroxides such as REE(OH) 2 + are identified as the primary species on the surface of kaolinite. Finally, compared to the typical ion-adsorption clays with intrinsic acidic pH, clays synthesized at basic pH exhibit similarly high rare earth ion-exchange efficiency with ammonium sulfate (AS), suggesting that rare earth ion-adsorption clays can exist in both acidic and basic environments.
Development of a Cost-Effective Extraction Process for the Recovery of Heavy and Critical Rare Earth Elements from the Clays and Shales Associated with Coal
The primary objective of the project was to investigate and develop a novel process technology that can extract and concentrate rare earth elements (REE) from coal refuse material, namely shales and clays, to a concentration of greater than or equal to 2% by weight. The extraction and recovery technologies developed in this project leverage the low-cost ion-exchange leaching techniques that are currently applied for commercial heavy rare earth production in South China. In addition to the ion-exchange extraction technology, the project also investigated a novel method of solution concentration and recovery based on ion and/or precipitate flotation.
Control of bubble ζ-potentials to improve the kinetics of bubble-particle interactions
Not provided.
Cleaning and dewatering fine coal
Fine coal is cleaned of its mineral matter impurities and dewatered by mixing the aqueous slurry containing both with a hydrophobic liquid, subjecting the mixture to a phase separation. The resulting hydrophobic liquid phase contains coal particles free of surface moisture and droplets of water stabilized by coal particles, while the aqueous phase contains the mineral matter. By separating the entrained water droplets from the coal particles mechanically, a clean coal product of substantially reduced mineral matter and moisture contents is obtained. The spent hydrophobic liquid is separated from the clean coal product and recycled. The process can also be used to separate one type of hydrophilic particles from another by selectively hydrophobizing one.