Search NASA⌕ Search

Engineering topics

Young, C. P., Jr.

Publications and source records attributed to Young, C. P., Jr..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Modal Correction Method For Dynamically Induced Errors In Wind-Tunnel Model Attitude Measurements

This paper describes a method for correcting the dynamically induced bias errors in wind tunnel model attitude measurements using measured modal properties of the model system. At NASA Langley Research Center, the predominant instrumentation used to measure model attitude is a servo-accelerometer device that senses the model attitude with respect to the local vertical. Under smooth wind tunnel operating conditions, this inertial device can measure the model attitude with an accuracy of 0.01 degree. During wind tunnel tests when the model is responding at high dynamic amplitudes, the inertial device also senses the centrifugal acceleration associated with model vibration. This centrifugal acceleration results in a bias error in the model attitude measurement. A study of the response of a cantilevered model system to a simulated dynamic environment shows significant bias error in the model attitude measurement can occur and is vibration mode and amplitude dependent. For each vibration mode contributing to the bias error, the error is estimated from the measured modal properties and tangential accelerations at the model attitude device. Linear superposition is used to combine the bias estimates for individual modes to determine the overall bias error as a function of time. The modal correction model predicts the bias error to a high degree of accuracy for the vibration modes characterized in the simulated dynamic environment.

Buehrle, R. D.↗
NASA NTRS1995

Dynamic response tests of inertial and optical wind-tunnel model attitude measurement devices

Results are presented for an experimental study of the response of inertial and optical wind-tunnel model attitude measurement systems in a wind-off simulated dynamic environment. This study is part of an ongoing activity at the NASA Langley Research Center to develop high accuracy, advanced model attitude measurement systems that can be used in a dynamic wind-tunnel environment. This activity was prompted by the inertial model attitude sensor response observed during high levels of model vibration which results in a model attitude measurement bias error. Significant bias errors in model attitude measurement were found for the measurement using the inertial device during wind-off dynamic testing of a model system. The amount of bias present during wind-tunnel tests will depend on the amplitudes of the model dynamic response and the modal characteristics of the model system. Correction models are presented that predict the vibration-induced bias errors to a high degree of accuracy for the vibration modes characterized in the simulated dynamic environment. The optical system results were uncorrupted by model vibration in the laboratory setup.

Buehrle, R. D.↗
NASA NTRS1985

Design and construction of models for the National Transonic Facility, part 1

The design and construction of models for the National Transonic Facility (NTF) has resulted in significant technology developments in many areas. This lecture covers the development of design criteria and major research and development work that has contributed to the successful design and fabrication models for testing at full scale Reynolds number the NTF. Emphasis is placed on the materials aspect of the design and fabrication proces, including metallic materials, mechanical properties characterization, new steel alloy development, fracture toughness enhancement, and identification of fillers and solders suitable for use in cryogenic models. Quantitative data are provided which will be of value to the potential user of NTF or for application to the design and fabrication of model systems for other cryogenic wind tunnels.

Young, C. P., Jr.↗
NASA NTRS1985

Design and construction of models for the National Transonic Facility, part 2

This lecture presents the results of fastener load and retention systems tests which were carried out as a part of the cryogenic models technology development program a the NASA Langley Research Center (LaRC). Various design concepts for the National Transonic Facility (NTF) developmental and production models are discussed. A number of NTF models are described with emphasis on materials used, uniqueness of design and design drivers. Design and fabrication experience is presented in terms of the primary thermal and mechanical considerations required for design as well as fabrication. Cost considerations are addressed in terms of factors influencing costs for NTF models and cost data comparisons which are taken from both NASA Langley and industry experience.

Young, C. P., Jr.↗
NASA NTRS1984

Cryogenic wind-tunnel model technology development activities at the NASA Langley Research Center

This paper summarizes the current cryogenic wind-tunnel model technology development activities at the NASA Langley Research Center. These research and development activities are being conducted in support of the design and fabrication of models for the new National Transonic Facility (NTF). The scope and current status of major research and development work is described and where available, data are presented from various investigations conducted to date. In addition, design and fabrication experience for existing developmental models to be tested in the NTF is discussed.

Young, C. P., Jr.↗
NASA NTRS1983

Cryogenic Wind Tunnel Models. Design and Fabrication

The principal motivating factor was the National Transonic Facility (NTF). Since the NTF can achieve significantly higher Reynolds numbers at transonic speeds than other wind tunnels in the world, and will therefore occupy a unique position among ground test facilities, every effort is being made to ensure that model design and fabrication technology exists to allow researchers to take advantage of this high Reynolds number capability. Since a great deal of experience in designing and fabricating cryogenic wind tunnel models does not exist, and since the experience that does exist is scattered over a number of organizations, there is a need to bring existing experience in these areas together and share it among all interested parties. Representatives from government, the airframe industry, and universities are included.

Young, C. P., Jr.↗
NASA NTRS1983

Model systems criteria

Design criteria were developed specifically for model systems to be tested at high Reynolds number in a cryogenic environment. More specifically, the criteria are aimed at identifying those special requirements and alternate criteria for utilizing the high Reynolds number facility (the National Transonic Facility).

Young, C. P., Jr.↗
NASA NTRS1981

Pathfinder model program for the National Transonic Facility

An overview of the Pathfinder Models Program is presented. The Pathfinder program is a major research and development activity in support of the National Transonic Facility Activation Plan. The program scope, models design approach, and Pathfinder model configurations are presented along with a discussion of major supportive program activities. The anticipated design criteria for NTF models are presented.

Young, C. P., Jr.↗
NASA NTRS1978

Nine percent nickel steel heavy forging weld repair study

The feasibility of making weld repairs on heavy section 9% nickel steel forgings such as those being manufactured for the National Transonic Facility fan disk and fan drive shaft components was evaluated. Results indicate that 9% nickel steel in heavy forgings has very good weldability characteristics for the particular weld rod and weld procedures used. A comparison of data for known similar work is included.

Young, C. P., Jr.↗
NASA NTRS1977

Recertification of the air and methane storage vessels at the Langley 8-foot high-temperature structures tunnel

This center operates a number of sophisticated wind tunnels in order to fulfill the needs of its researchers. Compressed air, which is kept in steel storage vessels, is used to power many of these tunnels. Some of these vessels have been in use for many years, and Langley is currently recertifying these vessels to insure their continued structural integrity. One of the first facilities to be recertified under this program was the Langley 8-foot high-temperature structures tunnel. This recertification involved (1) modification, hydrotesting, and inspection of the vessels; (2) repair of all relevant defects; (3) comparison of the original design of the vessel with the current design criteria of Section 8, Division 2, of the 1974 ASME Boiler and Pressure Vessel Code; (4) fracture-mechanics, thermal, and wind-induced vibration analyses of the vessels; and (5) development of operating envelopes and a future inspection plan for the vessels. Following these modifications, analyses, and tests, the vessels were recertified for operation at full design pressure (41.4 MPa (6000 psi)) within the operating envelope developed.

Hudson, C. M.↗
NASA NTRS1973

NASTRAN analysis of an air storage piping system

The application of NASTRAN to a complex piping design evaluation problem is summarized. Emphasis is placed on structural modeling aspects, problems encountered in modeling and analyzing curved pipe sections, principal results, and relative merits of using NASTRAN as a pipe analysis and design tool. In addition, the piping and manifolding system was analyzed with SNAP (Structural Network Analysis Program). The parallel SNAP study provides a basis for limited comparisons between NASTRAN and SNAP as to solution agreement and computer execution time and costs.

Young, C. P., Jr.↗