Search NASA⌕ Search

Engineering topics

Younger, P. R.

Publications and source records attributed to Younger, P. R..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Three dimensional scattering center imaging techniques

Two methods to image scattering centers in 3-D are presented. The first method uses 2-D images generated from Inverse Synthetic Aperture Radar (ISAR) measurements taken by two vertically offset antennas. This technique is shown to provide accurate 3-D imaging capability which can be added to an existing ISAR measurement system, requiring only the addition of a second antenna. The second technique uses target impulse responses generated from wideband radar measurements from three slightly different offset antennas. This technique is shown to identify the dominant scattering centers on a target in nearly real time. The number of measurements required to image a target using this technique is very small relative to traditional imaging techniques.

Younger, P. R.↗
NASA NTRS1981

An automated process sequence using preformed cell contacts and interconnects with a total cost of $0.64 per peak watt in 1986

A process sequence is described which utilizes a preformed metal mesh electrostatically bonded to each cell to provide the front contact. Cells of 12 percent AM1 efficiency have been produced using this scheme. This method also permits access to both contacts on the cell from the back side. In addition, low cost cell interconnection is accomplished using a flexible 'printed circuit' sheet which is ultrasonically bonded to the cell contacts. The complete process sequence as well as automated equipment which also uses ion implantation and pulse annealing is described. The total cost for module fabrication is estimated at $0.64 per peak watt for a 30 MW/year plant.

Armini, A. J.↗
NASA NTRS1981

Design, fabrication and performance of high efficiency photovoltaic modules

Design details and performance and environmental test results of newly developed high performance and reliability photovoltaic modules are presented. Efficiencies averaging 14.3% for 3040 cells were obtained by using ion implantation for cell junction and back surface field formation. 152 rectangular (6.0 cm x 4.6 cm) cells arranged with a 97% local packing density comprise the circuit assembly, and cells are wired 4 in parallel by 38 in series. The top cover of the superstrate design module is composed of tempered low-iron glass to provide transparent protection for the optical surface. Results show that this design has an encapsulation system which does not fail in the event of reverse-bias operation, and an average module efficiency of 12.2% was achieved at a 58.6W power which varied only 2% among all 20 modules.

Nowlan, M. J.↗
NASA NTRS1980

Development of glass encapsulation techniques for terrestrial photovoltaic arrays

Two parallel development programs for terrestrial solar cell module encapsulation and fabrication are reviewed, including the status of electrostatic bonding as an encapsulation technique. Current designs of electrostatically bonded modules are discussed, fabrication of which is now routine. The design of a high-efficiency module is presented, for which performance reliability features are discussed. This design is compatible with later generation changes such as the introduction of encapsulation by electrostatic bonding. Application of wire mesh contacts by electrostatic bonding has resulted in I-V curve fill factors of 0.74. Cell designs that would allow existing Pyrex glass to be used in electrostatically bonded modules are presented.

Younger, P. R.↗
NASA NTRS1979

Integral Glass Encapsulation for Solar Arrays

Work reported was performed during the period from August 1977 to December 1978. The program objective was to continue the development of electrostatic bonding (ESB) as an encapsulation technique for terrestrial cells. Economic analyses shows that this process can be a cost-effective method of producing reliable, long lifetime solar modules. When considered in sufficient volume, both material and equipment costs are competitive with conventional encapsulation systems. In addition, the possibility of integrating cell fabrication into the encapsulation process, as in the case of the preformed cell contacts discussed in this report, offers the potential of significant overall systems cost reduction.

Younger, P. R.↗
NASA NTRS1978

Integral assembly of photovoltaic arrays using glass

For a number of reasons glass is an excellent material for encapsulation of solar cell arrays. Glass can be readily available at relatively low cost. It exhibits excellent stability against degradation by solar ultraviolet illumination and atmospheric pollutants. A superior approach results if glass is employed directly as an integral encapsulant without secondary organic materials. A description is presented of a electrostatic bonding process which is being developed for integral assembly of glass encapsulated arrays. Solar cells are placed in contact with the glass surface, temperature is raised until the glass becomes ionically conductive, and an electric field is applied to initiate the bonding action. Silicon solar cells up to 3 inches in diameter have been integrally bonded without degradation.

Younger, P. R.↗
NASA NTRS1978

Terrestrial solar arrays with integral glass construction

An excellent encapsulation system for a terrestrial solar array can be formed using two sheets of glass. Superior technical character, very low cost and simple assembly can result if the active components and the glass sheets are integrally bonded together such that the array is hermetically sealed without employing organic encapsulation materials. Such an approach is being developed using electrostatic bonding. Status of this development is described. Functioning integral glass test modules have been fabricated and subjected to environmental testing. Results have been excellent.

Younger, P. R.↗