Search NASA⌕ Search

Engineering topics

Yu, Bo

Publications and source records attributed to Yu, Bo.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Tailoring-Orientated Deposition of Li 2 S for Extreme Fast-Charging Lithium–Sulfur Batteries

Precipitation/dissolution of insulating Li 2 S has long been recognized as the rate-determining step in lithium-sulfur (Li-S) batteries, which dramatically undermines sulfur utilization at elevated charging rates. Herein, we present an orientated Li 2 S deposition strategy to achieve extreme fast charging (XFC, ≤15 min) through synergistic control of porosity, electronic conductivity, and anchoring sites of electrode substrate. Via magnesiothermic reduction of a zeolitic imidazolate framework, a nitrogen-doped and hierarchical porous carbon with highly graphitic phase was developed. This design effectively reduces interfacial resistance and ensures efficient sequestration of polysulfides during deposition, leading to (110)-preferred growth of Li 2 S nanocrystalline between (002)-dominated graphitic layers. Our approach directs an alternative Li 2 S deposition pathway to the commonly reported lateral growth and 3D thickening growth mode, ameliorating the electrode passivation. Therefore, a Li-S cell capable of charging/discharging at 5C (12 min) while maintaining excellent cycling stability (82% capacity retention) for 1000 cycles is demonstrated. In conclusion, even under high S loading (8.3 mg cm -2 ) and low electrolyte/sulfur ratio (3.8 mL mg -1 ), the sulfur cathode still delivers a high areal capacity of >7 mAh cm -2 for 80 cycles.

25 ENERGY STORAGE↗
DOE OSTI2023

Novel waste-derived non-noble metal catalysts to accelerate acidic and alkaline hydrogen evolution reaction

Carbon substrate support is a promising approach to facilitate catalytic activity of non-noble metal catalysts in hydrogen evolution reactions (HER). Here, in this paper, we report a waste-derived electrocatalyst P-CoNiO 2 @NC synthesized under mild condition. It exhibits outstanding HER performance in both acid (η 10 = 64.6 mV) and alkaline (η 10 = 96.4 mV) condition with good stability. Especially, it begins to outperform commercial Pt/C when the current density is over 74 mA/cm 2 in acid electrolyte and 29 mA/cm 2 in alkaline electrolyte. Moreover, the waste-derived carbon substrate could effectively promote HER activity of other dual 3d TMOs such as Fe and Co, Fe and Ni. The improved HER activity originates from electron transfer, electronic structure adjustment and optimization of intermediates adsorption according to X -ray photoelectron spectroscopy and density functional theory calculations. This work provides a new insight for converting wastes into value-added products and a sustainable and friendly strategy to facilitate hydrogen energy production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Conversion efficiency improvement of ELO GaAs solar cell, deposited on water soluble sacrificial buffer

Here, we demonstrate the improvement of power conversion efficiency of an epitaxially-lifted-off single junction GaAs solar cell deposited on a water-soluble sacrificial buffer architecture by introducing an additional germanium (Ge) interlayer between GaAs and the fluoride buffer. The epitaxial lift-off (ELO) technique has been extensively used to separate III-V device layers from their single crystal GaAs substrates. However, conventional ELO requires the use of concentrated hydrofluoric acid (HF) for extended times to etch out the sacrificial layer, subsequently degrading the surface roughness of the parent wafer. As a result, the wafer has to undergo expensive and intensive chemical mechanical polishing (CMP) processes, costing about 25% of a pristine 6-inch GaAs substrate. In our previous work, we demonstrated a method to eliminating the need for CMP post-processing by using water-assisted ELO (H 2 O-ELO). A water-soluble, 3-layer buffer architecture was developed using alkaline earth compounds. However, devices suffered low performance due to a high defect density in the GaAs active layers. A Ge interlayer was introduced to provide a more favorable surface energy for GaAs growth, which leads to an improvement of GaAs crystal quality. The Ge deposition conditions were optimized to achieve a high-quality Ge layer on triple-layer fluoride buffer. Single junction GaAs devices fabricated on Ge/(Ca,Sr)F 2 /BaF 2 /(Ca,Sr)F 2 showed improvement of solar cell performance parameters featuring increases in V oc by 23.7%, and fill factor (F.F.) by 4.9%, which results in an overall improvement of power conversion efficiency from 10.3% to 12.69%.

14 SOLAR ENERGY↗
DOE OSTI2022

III-V Solar Cells with Novel Epitaxial Lift-off Architectures for Extended Substrate Reuse for Low-cost Manufacturing

The highest solar cell efficiencies have been achieved with III-V photovoltaics (PV). Still, the use of III-V materials in terrestrial applications has been very limited, mainly because of their high cost. The high cost is primarily due to the expensive Ge or GaAs wafers which could amount up to one-half of the total module cost! A prominent approach to reduce the impact of the high cost of substrates used for III-V PV is through re-use of the wafer substrates by Epitaxial Lift-Off (ELO). Typically, using a sacrificial layer such as AlAs, the device part of the cell is lifted off, leaving behind the substrate for re-use for fabrication of the next device. While conversion efficiency as high as 29.1% has been achieved by ELO method, chemical mechanical polishing (CMP) of the substrate is required which significantly adds to the overall solar cell cost. In this project, we have developed a novel ELO architecture for single junction gallium arsenide (GaAs) solar cells that will not require CMP of the substrate for re-use. Multiple reuses of GaAs wafers have been demonstrated with no CMP, without degradation in solar cell efficiency. Also, the solar cells have been successfully lifted off and transferred to inexpensive substrates with less than 2% change in efficiency. By elimination of the CMP process, which is the highest cost component of III-V solar cells made by conventional ELO method (~$10/W), and decreasing the substrate cost by multiple re-uses, the developed technology could be a leap forward in significantly reducing the cost of III-V photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2022

From Salt to Electronics: Heteroepitaxy and GaAs Solar Cells

This paper presents work on the heteroepitaxy of salts, specifically fluorides, on semiconductor and heteroepitaxy of semiconductor on salts. Fluorides layers are deposited on commercial Gallium Arsenide (GaAs) wafers followed by the heteroepitaxial growth of GaAs using metal organic chemical vapor deposition (MOCVD). The fluoride layers consist of 2 lattice-engineered layers of alkaline-earth compounds to match with GaAs, and are used to sandwich another alkaline-earth compound with higher water-solubility as sacrificial layer. The triple fluoride layers enable liftoff of free-standing semiconductor films which can be further transferred to desirable substrates. 2D-X-ray Diffraction (2D-XRD) measurements confirm epitaxial growth of both the fluorides and the subsequently grown GaAs films. Single junction (SJ) solar cell devices based on thus prepared films show a power conversion efficiency (PCE) of 10.3% under 1 sun illumination. After the completion of device fabrications, the GaAs film is lifted off from the substrate by a novel water-assisted epitaxial liftoff (H 2 O-ELO) technique and transferred to a cheaper substrate. The original GaAs wafer is recycled and reused twice. Devices based on reused substrates show no significant degradation in performance. Lastly, the semiconductor-salt-semiconductor scheme has great implications in high performance, flexible, and large area electronics.

14 SOLAR ENERGY↗
DOE OSTI2022

PURE Biomanufacturing: Secure, Pandemic-Adaptive Biomanufacturing

Biopharmaceutical production systems and processes are vulnerable to cyberattacks from sophisticated adversaries. Consequently, it is imperative to start building biopharmaceutical manufacturing systems that offer verifiable formalism and transform the current state of security across all production stages.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Crash Risks Evaluation of Urban Expressways: A Case Study in Shanghai

We report that proactive traffic safety management systems can reduce crashes by identifying crash precursors, evaluating real-time crash risks, and implementing suitable interventions. The basic prerequisite for developing such a system is to propose a reliable crash risk evaluation model that takes real-time traffic flow data as input. Previous studies have primarily focused on real-time crash prediction using some statistical or machine-learning methods. However, further quantitative evaluation and classification of crash risks have been ignored. In this study, we conduct a systematic crash risk evaluation workflow, including crash risk prediction, crash risk quantification, and crash risk classification. Specifically, the crash risk prediction using an extended logit model is proposed, from which CAS, CSD, UAS, DAS, DTV are identified to be contributing factors of crash risks. Then a crash risk quantification model based on the parameter evaluation of the extended logit model is developed. The crash risks of urban expressways and their spatial-temporal evolution trends are quantified. Finally, the crash risks are classified into high crash risk level, moderate crash risk level, and low crash risk level by the k-means cluster algorithm. Then the threshold boundaries of different crash risk levels are determined. The research results provide a proactive guidance for traffic safety management of urban expressways.

33 ADVANCED PROPULSION SYSTEMS↗