Search NASA⌕ Search

Engineering topics

Yu, D. L.

Publications and source records attributed to Yu, D. L..

Recent advance progress of HL-3 experiments

Since the first plasma realized in 2020, a series of key systems on HL-3 (known as HL-2M before) tokamak have been equipped/upgraded, including in-vessel components (the first wall, lower divertor, and toroidal cryogenic/water-cooling/baking/glow discharge systems, etc.), auxiliary heating system of 11 MW, and 28 diagnostic systems (to measure the plasma density, electron temperature, radiation, magnetic field, etc.). Magnet field systems were commissioned firstly for divertor plasma discharges. During the 2nd experimental campaign of HL-3 tokamak, several great progresses have been achieved. Firstly, the successful operation with plasma current larger than 1 MA was achieved under a divertor configuration. Secondly, the advanced divertor concept with two distinct snowflake configurations was realized. It is found that the distribution of ion saturation current and heat flux on bottom plate becomes wide due to magnetic surface expansion, demonstrating the advantage of such configuration in the heat flux mitigation. In addition, using the combination of NBI, ECRH and LHCD, the standard sawtoothing high confinement mode of megampere plasma was firstly accessed on the HL-3. The successful commissioning of HL-3 is beneficial for the initial operation of ITER.

1 MA plasma↗

Toroidal modeling of plasma flow damping and density pump-out by RMP during ELM mitigation in HL-2A

Reduction of both the plasma density and toroidal flow speed, due to application of the predominantly n = 1 (n is the toroidal mode number) resonant magnetic perturbation (RMP) for controlling the edge localized mode in the HL-2A tokamak, is numerically investigated utilizing the quasi-linear initial-value code MARS-Q (Liu et al 2013 Phys. Plasmas 20 042503). Simulation results reveal that the neoclassical toroidal viscosity (NTV) due to three dimensional fields plays the key role in modifying the plasma momentum and particle transport in the HL-2A discharge. By comparing the modeling results with the measured density pump-out in the experiment, the electron NTV particle flux model, in combination with the free-boundary condition for the axisymmetric change of the density at the plasma edge, is found to yield the best agreement in terms of both the pump-out level and the overall time scale. Further sensitivity studies show that the simulated density pump-out level is reasonably robust against variations in the model assumptions, including the particle diffusion model and the non-ambipolar versus ambipolar NTV particle flux. The latter however affects the time scale for reaching the steady state solution. Finally, it is found that the plasma edge-peeling response, the NTV torque, as well as the plasma momentum and particle transport, all are sensitive to the toroidal phase difference between the upper and lower rows of the RMP coil currents in HL-2A, with the 30 ∘ coil phasing producing the minimal side effects on the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ideal internal kink stability in presence of plasma flow and neoclassical toroidal viscosity due to energetic particles

Abstract The influence of energetic particles (EPs) on the ideal internal kink mode, in rotating tokamak plasmas, is numerically investigated by simultaneously solving MHD-kinetic hybrid equations together with a toroidal momentum balance equation utilizing the MARS-Q code (Liu et al 2013 Phys. Plasmas 20 042503). The neoclassical toroidal viscous (NTV) torque, induced by precessional drift resonances of trapped energetic particles, acts as the momentum sink term to damp the plasma flow. Quasi-linear initial value simulations show local reduction of the flow amplitude and enhancement of the flow shear near the q = 1 rational surface ( q is the safety factor) due to EP induced NTV. Both effects in turn destabilize the internal kink mode. These numerical findings are robust against the initial linear stability of internal kink, the initial plasma flow profile, as well as the equilibrium distribution model for EPs.

Physics↗