Search NASA⌕ Search

Engineering topics

Yu, W

Publications and source records attributed to Yu, W.

At least 19 records

Acceleration of laser-driven ion bunch from double-layer thin foils

Generation of monoenergetic ion bunch from a double-layer thin-foil target irradiated by an intense linearly polarized laser pulse is investigated using two-dimensional particle-in-cell simulation. The protons in the front low-density hydrogen target layer accelerated by the space-charge field of the laser-driven hot electrons can penetrate through the high-Z high-mass and high-density ion layer, resulting in an energetic proton bunch. A part of the latter is further accelerated by the space-charge field of the hot electrons in the vacuum behind the high-Z ion layer. With this scheme, quasi-monoenergetic proton bunches can be produced using presently available laser pulses of moderate contrast and duration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Effects of Oxide Supports on the Low Temperature Hydrogenation Activity of Acetone over Pt/Ni Bimetallic Catalysts on SiO2 gamma-Al2O3 and TiO2

Low temperature (308 K) hydrogenation of acetone was used as a probe reaction to investigate the support effect on the hydrogenation activity of Pt/Ni bimetallic catalysts supported on TiO{sub 2}, SiO{sub 2} and {gamma}-Al{sub 2}O{sub 3}. The oxide supports significantly affected the catalytic properties of Pt/Ni catalysts, in which Pt/Ni/SiO2 bimetallic catalysts exhibited significantly higher activity than the other two bimetallic catalysts. TEM measurements revealed that the three supported Pt/Ni bimetallic catalysts have similar particle size distribution, while CO chemisorption measurements showed very different chemisorption capacity. Extended X-Ray absorption fine structure (EXAFS) measurements of the Pt L{sub III}-edge indicated that Pt atoms were fully reduced and the Pt-Ni bimetallic bonds were formed on all three catalysts. The extent of Pt-Ni bond formation followed the trend of SiO{sub 2} > {gamma}-Al{sub 2}O{sub 3} > TiO{sub 2}, which correlated very well with the hydrogenation activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanofluids for heat transfer : an engineering approach.

An overview of systematic studies that address the complexity of nanofluid systems and advance the understanding of nanoscale contributions to viscosity, thermal conductivity, and cooling efficiency of nanofluids is presented. A nanoparticle suspension is considered as a three-phase system including the solid phase (nanoparticles), the liquid phase (fluid media), and the interfacial phase, which contributes significantly to the system properties because of its extremely high surface-to-volume ratio in nanofluids. The systems engineering approach was applied to nanofluid design resulting in a detailed assessment of various parameters in the multivariable nanofluid systems. The relative importance of nanofluid parameters for heat transfer evaluated in this article allows engineering nanofluids with desired set of properties.

42 ENGINEERING↗

Pressure drop, heat transfer, critical heat flux, and flow stability of two-phase flow boiling of water and ethylene glycol/water mixtures - final report for project "Efficent cooling in engines with nucleate boiling."

Because of its order-of-magnitude higher heat transfer rates, there is interest in using controllable two-phase nucleate boiling instead of conventional single-phase forced convection in vehicular cooling systems to remove ever increasing heat loads and to eliminate potential hot spots in engines. However, the fundamental understanding of flow boiling mechanisms of a 50/50 ethylene glycol/water mixture under engineering application conditions is still limited. In addition, it is impractical to precisely maintain the volume concentration ratio of the ethylene glycol/water mixture coolant at 50/50. Therefore, any investigation into engine coolant characteristics should include a range of volume concentration ratios around the nominal 50/50 mark. In this study, the forced convective boiling heat transfer of distilled water and ethylene glycol/water mixtures with volume concentration ratios of 40/60, 50/50, and 60/40 in a 2.98-mm-inner-diameter circular tube has been investigated in both the horizontal flow and the vertical flow. The two-phase pressure drop, the forced convective boiling heat transfer coefficient, and the critical heat flux of the test fluids were determined experimentally over a range of the mass flux, the vapor mass quality, and the inlet subcooling through a new boiling data reduction procedure that allowed the analytical calculation of the fluid boiling temperatures along the experimental test section by applying the ideal mixture assumption and the equilibrium assumption along with Raoult's law. Based on the experimental data, predictive methods for the two-phase pressure drop, the forced convective boiling heat transfer coefficient, and the critical heat flux under engine application conditions were developed. The results summarized in this final project report provide the necessary information for designing and implementing nucleate-boiling vehicular cooling systems.

42 ENGINEERING↗