Search NASA⌕ Search

Engineering topics

Yu, Weilai

Publications and source records attributed to Yu, Weilai.

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Hyperconjugation-controlled molecular conformation weakens lithium-ion solvation and stabilizes lithium metal anodes

Tuning the solvation structure of lithium ions via electrolyte engineering has proven effective for lithium metal (Li) anodes. Further advancement that bypasses the trial-and-error practice relies on the establishment of molecular design principles. Expanding the scope of our previous work on solvent fluorination, we report here an alternative design principle for non-fluorinated solvents, which potentially have reduced cost, environmental impact, and toxicity. By studying non-fluorinated ethers systematically, we found that the short-chain acetals favor the [gauche, gauche] molecular conformation due to hyperconjugation, which leads to weakened monodentate coordination with Li + . The dimethoxymethane electrolyte showed fast activation to >99% coulombic efficiency (CE) and high ionic conductivity of 8.03 mS cm -1 . The electrolyte performance was demonstrated in anode-free Cu$∥$LFP pouch cells at current densities up to 4 mA cm -2 (70 to 100 cycles) and thin-Li$∥$high-loading-LFP coin cells (200–300 cycles). Overall, we demonstrated and rationalized the improvement in Li metal cyclability by the acetal structure compared to ethylene glycol ethers. We expect further improvement in performance by tuning the acetal structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Dynamic Bubbling Balanced Proactive CO 2 Capture and Reduction on a Triple-Phase Interface Nanoporous Electrocatalyst

The formation and preservation of the active phase of the catalysts at the triple-phase interface during CO 2 capture and reduction is essential for improving the conversion efficiency of CO 2 electroreduction toward value-added chemicals and fuels under operational conditions. Designing such ideal catalysts that can mitigate parasitic hydrogen generation and prevent active phase degradation during the CO 2 reduction reaction (CO 2 RR), however, remains a significant challenge. Herein, we developed an interfacial engineering strategy to build a new SnO x catalyst by invoking multiscale approaches. This catalyst features a hierarchically nanoporous structure coated with an organic F-monolayer that modifies the triple-phase interface in aqueous electrolytes, substantially reducing competing hydrogen generation (less than 5%) and enhancing CO 2 RR selectivity (~90%). This rationally designed triple-phase interface overcomes the issue of limited CO 2 solubility in aqueous electrolytes via proactive CO 2 capture and reduction. Concurrently, we utilized pulsed square-wave potentials to dynamically recover the active phase for the CO 2 RR to regulate the production of C1 products such as formate and carbon monoxide (CO). This protocol ensures profoundly enhanced CO 2 RR selectivity (~90%) compared with constant potential (~70%) applied at -0.8 V (V vs RHE). We further achieved a mechanistic understanding of the CO 2 capture and reduction processes under pulsed square-wave potentials via in situ Raman spectroscopy, thereby observing the potential-dependent intensity of Raman vibrational modes of the active phase and CO 2 RR intermediates. Finally, this work will inspire material design strategies by leveraging triple-phase interface engineering for emerging electrochemical processes, as technology moves toward electrification and decarbonization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Failure Process During Fast Charging of Lithium Metal Batteries with Weakly Solvating Fluoroether Electrolytes

While improving the lithium metal (Li) Coulombic efficiency has been a focus for electrolyte design, the performance under high current densities is less studied yet highly relevant for practical applications. Here, we evaluate the charge-rate-dependent cycling stability using three types of weakly solvating fluoroether electrolytes. Although good cycle life was achieved in all three electrolytes under low current densities, they all exhibited a soft shorting behavior above various threshold current densities (between 2 and 5.2 mA cm –2 ). In this study, we attributed the current-dependent electrode morphology to both Li growth and residual solid electrolyte interface (rSEI) growth processes. In early cycles, Li morphology guided the formation of rSEI structures. In later cycles, the rSEI structure partially impacted Li growth. Under low current densities, the rSEI was inhomogeneous with large voids for subsequent bulky lithium growth. Under high current densities, the rSEI became more dense, which aggravated the high-surface/volume-ratio Li growth through and on the top of the rSEI. Among the three weakly solvating fluoroether electrolytes, the ones with lower ionic conductivity were observed to short within fewer cycles and at lower charge current densities. Our work suggests that fast ion transport in electrolytes may be a desirable feature for the stable operation at >1C charging in high-energy-density lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Impact of the fluorination degree of ether-based electrolyte solvents on Li-metal battery performance

Electrolytes using fluorinated solvents have proven effective in improving the cycling life of Li-metal batteries, by forming a robust solid–electrolyte interphase through decomposition of anion and fluorinated solvent molecules. Herein, we modulated the fluorination degree of ether-based electrolyte solvents to investigate their performance in Li-metal batteries. Here, we tuned the fluorination degree by installing a monofluoro substituent on one ethoxy group of 1,2-diethoxyethane (DEE) and varying the fluorination degree on the other one, providing three fluorinated DEE solvent molecules (i.e., F1F0, F1F1 and F1F2) with a relatively low fluorination degree. All three electrolytes showed improved solvation strength and ionic conductivities compared with previous highly fluorinated DEE electrolytes while retaining good oxidative stability. A full cell test using the Li-metal anode and nickel-rich cathode revealed that a higher degree of fluorination is beneficial to the cycling performance, and the cycling stability follows F1F0 < F1F1 < F1F2. Specifically, F1F0 exhibited poor cycling stability due to its instability against both the anode and cathode. While F1F1 and F1F2 both showed good stability against the Li metal anode, their relative long-term oxidative stability was responsible for the distinct performance, in which the cycle numbers at 80% capacity retention for F1F1 and F1F2 were ~20 and ~80, respectively. Finally, we demonstrated that F1F2 was able to achieve 90 cycles before reaching 80% capacity retention in practical lithium iron phosphate (LFP) pouch cells. This work shows the importance of modulating the fluorination degree of electrolyte solvents, and this approach is suitable for various cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2022

Failure Modes of Platinized pn+-GaInP Photocathodes for Solar-Driven H2 Evolution

The long-term stability for the hydrogen-evolution reaction (HER) of homojunction pn+-Ga0.52In0.48P photocathodes (band gap = 1.8 eV) with an electrodeposited Pt catalyst (pn+-GaInP/Pt) has been systematically evaluated in both acidic and alkaline electrolytes. Electrode dissolution during chronoamperometry was correlated with changes over time in the current density-potential (J-E) behavior to reveal the underlying failure mechanism. Pristine pn+-GaInP/Pt photocathodes yielded an open-circuit photopotential (Eoc) as positive as >1.0 V vs the potential of the reversible hydrogen electrode (RHE) and a light-limited current density (Jph) of >12 mA cm-2 (1-sun illumination). However, Eoc and Jph gradually degraded at either pH 0 or pH 14. The performance degradation was attributed to three different failure modes: (1) gradual thinning of the n+-emitter layer due to GaInP dissolution in acid; (2) active corrosion of the underlying GaAs substrate at positive potentials causing delamination of the upper GaInP epilayers; and (3) direct GaAs/electrolyte contact compromising the operational stability of the device. This work reveals the importance of both substrate stability and structural integrity of integrated photoelectrodes toward stable solar fuel generation.

CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSICS,S↗
DOE OSTI2022

Tuning Fluorination of Linear Carbonate for Lithium-Ion Batteries

Liquid electrolyte engineering plays a critical role in modern lithium-ion batteries. However, the existing electrolytes fall short when used with some trending battery chemistries such as high-voltage and high-energy-density electrodes. Fluorination of electrolyte solvents has been identified as an effective approach for improved cyclability, but few works systematically studied the effects of fluorination extent of carbonate solvents on battery performance. Here we design and synthesize a family of fluorinated ethyl methyl carbonates. Different numbers of F atoms are finely tuned to yield monofluoroethyl methyl carbonate (F1EMC), difluoroethyl methyl carbonate (F2EMC) and trifluoroethyl methyl carbonate (F3EMC). The cycling behavior of several types of lithium-ion pouch cells, including graphite (Gr)/single-crystalline LiNi 0.8 Mn 0.1 Co 0.1 O 2 (SC-NMC811), Gr-SiO x /LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), high-voltage Gr/LiNi 0.5 Mn 1.5 O 4 (LNMO), Gr/layered Li-rich Mn-based oxide (LLMO) and fast-charging Gr/NMC622, were systematically investigated to understand the impact of fluorination degree. Compared to the commercially available F3EMC, we found that the partially-fluorinated F1EMC and F2EMC in some cases showed improved cycling stability, which we attribute to their locally-polar –CH 2 F and –CHF 2 groups and thus fast ion conduction than –CF 3 . This work suggests that highly or fully fluorinated solvents are not necessarily desirable; instead, fluorination degree needs to be rationally and finely tuned for optimized lithium-ion cell performance.

25 ENERGY STORAGE↗
DOE OSTI2021

Catalytic open-circuit passivation by thin metal oxide films of p-Si anodes in aqueous alkaline electrolytes

Ni and NiO x -based protective thin films are shown to catalyze the oxidation of Si in the presence of O 2 in strongly alkaline KOH(aq) even in the absence of illumination. The O 2 in solution drove the open-circuit potential of the electrode to >0.4 V, which is positive of the Si passivation potential. The elevated electrochemical potential of the surface promoted formation of passive oxides on exposed Si regions of Si/Ni electrodes. Catalytic passivation of Si extended the durability of an np + -Si(100)/NiO x photoanode to >400 h while operating under simulated day/night cycles. In contrast, electrodes without a Ni(O x ) layer and/or without O 2 in solution displayed direct etching of the Si and corrosion pitting during non-illuminated, simulated nighttime episodes of day/night cycling. The O 2 -derived catalyzed passivation of Si using thin films can be generalized to multiple phases of NiO x as well as to materials other than Ni. Finally, relative to operation in aqueous alkaline conditions, decreasing the pH of the electrolyte decreased the dissolution rate of the protective oxide layer formed by the catalyzed passivation process, and consequently increased the durability of the photoanode, but yielded lower photoelectrode fill factors for water oxidation due to the relatively large kinetic overpotentials for the electrocatalyzed oxygen-evolution reaction at near-neutral pH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Understanding the Stability of Etched or Platinized p-GaInP Photocathodes for Solar-Driven H 2 Evolution

The long-term stability in acidic or alkaline aqueous electrolytes of p-Ga 0.52 In 0.48 P photocathodes, with a band gap of ~1.8 eV, for the solar-driven hydrogen-evolution reaction (HER) has been evaluated from a thermodynamic, kinetic, and mechanistic perspective. At either pH 0 or pH 14, etched p-GaInP electrodes corroded cathodically under illumination and formed metallic In 0 on the photoelectrode surface. In contrast, under the same conditions, electrodeposition of Pt facilitated the HER kinetics and stabilized p-GaInP/Pt photoelectrodes against such cathodic decomposition. When held at 0 V versus the reversible hydrogen electrode, p-GaInP/Pt electrodes in either pH = 0 or pH = 14 exhibited stable current densities (J) of ~-9 mA cm -2 for hundreds of hours under simulated 1 sun illumination. During the stability tests, the current density-potential (J-E) characteristics of the p-GaInP/Pt photoelectrodes degraded due to pH-dependent changes in the surface chemistry of the photocathode. This work provides a fundamental understanding of the stability and corrosion mechanisms of p-GaInP photocathodes that constitute a promising top light absorber for tandem solar-fuel generators.

14 SOLAR ENERGY↗
DOE OSTI2021

Optical and electrochemical effects of H 2 and O 2 bubbles at upward-facing Si photoelectrodes

The effects of the size, contact-angle, and coverage of gas bubbles on solar fuels devices were characterized at cm-scale, upward-facing planar and microwire-array Si photoelectrodes in stagnant electrolytes. Experimental measurements were supported by ray-tracing simulations of surface attached gas bubble films. A dilute, redox-active tracer allowed for the quantification of the mass-transport effects of bubble coverage during photoanodic O 2 (g) evolution at upward-facing photoanodes in 1.0 M KOH(aq.). Measurements of the gas coverage at upward-facing p-Si photocathodes in 0.50 M H 2 SO 4 (aq.) allowed for the nucleation rate and contact angle of H 2 (g) bubbles to be evaluated for systems having various surface free energies. Under simulated solar illumination, the rapid departure of small O 2 (g) bubbles produced stable photocurrents at upward-facing oxygen-evolving Si photoanodes and yielded increased mass-transport velocities relative to a stagnant electrolyte, indicating that bubbles can provide a net benefit to the photoelectrochemical performance of an upward-facing photoanode in solar fuels devices.

14 SOLAR ENERGY↗
DOE OSTI2021

Investigations of the stability of etched or platinized p-InP(100) photocathodes for solar-driven hydrogen evolution in acidic or alkaline aqueous electrolytes

Here, the stability of p-InP photocathodes performing the hydrogen-evolution reaction (HER) has been evaluated in contact with either 1.0 M H 2 SO 4 (aq) or 1.0 M KOH(aq), with a focus on identifying corrosion mechanisms. Stability for the solar-driven HER was evaluated using p-InP electrodes that were either etched or coated with an electrodeposited Pt catalyst (p-InP/Pt). Variables such as trace O 2 were systematically controlled during the measurements. Changes in surface characteristics after exposure to electrochemical conditions as well as electrode dissolution processes were monitored using X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma mass spectrometry (ICP-MS). In either H 2 SO 4 or KOH, etched p-InP photoelectrodes corroded cathodically under illumination, forming metallic In 0 at the electrode surface. In contrast, electrodeposition of Pt kinetically stabilized illuminated p-InP photocathodes in both H 2 SO 4 and KOH by inhibiting the cathodic corrosion pathway. Notably, when held at 0 V vs. the reversible hydrogen electrode (RHE) in 1.0 M H 2 SO 4 (aq), p-InP/Pt exhibited a stable current density (J) of ~–18 mA cm –2 for >285 h under simulated 1 Sun illumination. The long-term current density vs. potential (J–E) behavior at pH 0 and pH 14 of p-InP/Pt photocathodes correlated with changes in the surface chemistry as well as the dissolution of p-InP. In acidic media, the J–E behavior of p-InP/Pt photocathodes remained nearly constant with time, but the surface of a p-InP/Pt electrodes gradually turned P-rich via a slow and continuous leaching of In ions. In alkaline electrolyte, the surface of p-InP/Pt electrodes was passivated by formation of an InO x layer that exhibited negligible dissolution but led to a substantial degradation in the J–E characteristics. Consequently, changes in the catalytic kinetics and surface stoichiometry are both important considerations for determining the corrosion chemistry and the long-term operational stability of InP photoelectrodes.

14 SOLAR ENERGY↗
DOE OSTI2021

Investigations of the stability of GaAs for photoelectrochemical H 2 evolution in acidic or alkaline aqueous electrolytes

The long-term stability of p-GaAs photocathodes has been investigated for the hydrogen-evolution reaction (HER) in contact with either 1.0 M H 2 SO 4 (aq) or 1.0 M KOH(aq). Stability for the HER was evaluated using p-GaAs electrodes that were either etched or coated with active HER catalysts (Pt and CoP). Changes in surface characteristics of GaAs after exposure to electrochemical conditions were monitored by X-ray photoelectron spectroscopy (XPS), and electrode dissolution processes were evaluated by inductively coupled plasma mass spectrometry (ICP-MS). Consistent with thermodynamic predictions, after operation of the HER at pH 0 or pH 14, illuminated etched p-GaAs electrodes exhibited minimal dissolution while preserving a nearly stoichiometric surface. Electrodeposition or sputtering of Pt on the p-GaAs surface promoted the formation of excess As 0 via an interfacial reaction during the HER. The resulting non-stoichiometric As 0 -rich surface of p-GaAs/Pt electrodes caused a loss in photoactivity as well as substantial cathodic dark current. In contrast, p-GaAs electrodes coated with thin-film CoP catalysts did not display an increase in surficial As 0 after operation of the HER in acidic electrolytes. Minimization of deleterious interfacial reactions is thus critical to obtain extended stability in conjunction with high performance from p-GaAs photocathodes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Cathodic NH 4 + leaching of nitrogen impurities in CoMo thin-film electrodes in aqueous acidic solutions

Electrocatalytic reduction of dinitrogen (N 2 ) to ammonium (NH 4 + ) in acidic aqueous solutions was investigated at ambient temperature and pressure using a cobalt–molybdenum (CoMo) thin-film electrode prepared by magnetron reactive sputtering. Increased concentrations of ammonium ions (NH 4 + ) were consistently detected in the electrolyte using ion chromatography (IC) after constant-potential electrolysis at various potentials (≤-0.29 V vs. RHE). Using a newly developed analytical method based on ammonia derivatization, performing the experiments with 15 N 2 -labelled gas led however to the detection of increased 14 NH 4 + concentrations instead of 15 NH 4 + . X-ray photoelectron spectroscopic (XPS) analysis of the electrode surface revealed the presence of Mo[triple bond, length as m-dash]N and Mo–NH x species. Several contamination sources were identified that led to substantial increases in the concentration of ammonium ions, including 15 NH 3 impurities in 15 N 2 gas. The observed ammonium concentrations can be consistently ascribed to leaching of nitrogen ( 14 N) impurities incorporated in the CoMo film during the sputtering process. Therefore, researchers in the field are urged to adopt extended protocols to identify and eliminate sources of ammonia contamination and to very carefully monitor the ammonium concentrations in each experimental step.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomic force microscopy: Emerging illuminated and operando techniques for solar fuel research

Integrated photoelectrochemical devices rely on the synergy between components to efficiently generate sustainable fuels from sunlight. The micro- and/or nanoscale characteristics of the components and their interfaces often control critical processes of the device, such as charge-carrier generation, electron and ion transport, surface potentials, and electrocatalysis. Understanding the spatial properties and structure–property relationships of these components can provide insight into designing scalable and efficient solar fuel components and systems. These processes can be probed ex situ or in situ with nanometer-scale spatial resolution using emerging scanning-probe techniques based on atomic force microscopy (AFM). In this Perspective, we summarize recent developments of AFM-based techniques relevant to solar fuel research. We review recent progress in AFM for (1) steady-state and dynamic light-induced surface photovoltage measurements; (2) nanoelectrical conductive measurements to resolve charge-carrier heterogeneity and junction energetics; (3) operando investigations of morphological changes, as well as surface electrochemical potentials, currents, and photovoltages in liquids. Opportunities for research covered here include: (1) control of ambient conditions for performing AFM measurements; (2) in situ visualization of corrosion and morphological evolution of electrodes; (3) operando AFM techniques to allow nanoscale mapping of local catalytic activities and photo-induced currents and potentials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Isotopically Selective Quantification by UPLC-MS of Aqueous Ammonia at Submicromolar Concentrations Using Dansyl Chloride Derivatization

Ammonia (NH 3 ) is necessary for food production and is commercially synthesized from nitrogen (N 2 ) and hydrogen (H 2 ) using the Haber–Bosch process. Significant amounts of ammonia are made every year in a reaction that requires high temperatures and pressures, with the Haber–Bosch accounting for ~1.6% of total annual global energy consumption. Electrocatalysts are also being explored to convert in an environmentally friendly manner N 2 to NH 3 at ambient temperature and pressure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗