Search NASA⌕ Search

Engineering topics

Yuska, J. A.

Publications and source records attributed to Yuska, J. A..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

NASA refan program status

The objective of the refan program is to demonstrate the technical feasibility of substantially reducing the noise levels of existing JT8D powered aircraft. The program consists of the design, manufacturing and testing of the refan engines and modified nacelles and airplanes. Experimental testing has been completed for the refan engine both at sea level and at altitude conditions. Ground testing for the B727 side- and center-engine installations and flight testing of the DC-9 with refan engines and acoustic nacelles have been performed. Analyses of the test results are in progress. Preliminary results presented in this paper show that substantial noise reductions were achieved.

Abdalla, K. L.↗
NASA NTRS1975

NASA refan program status

The objective of the refan program is to demonstrate the technical feasibility of substantially reducing the noise levels of existing JT8D powered aircraft. The program consists of the design, manufacturing and testing of the refan engines and modified nacelles and airplanes. Experimental testing was completed for the refan engine both at sea level and at altitude conditions. Ground testing for the B727 side- and center-engine installations and flight testing of the DC-9 with refan engines and acoustic nacelles were performed. Preliminary results presented show that substantial noise reductions were achieved.

Abdalla, K. L.↗
NASA NTRS1973

Performance characteristics of a model VTOL lift fan in crossflow.

This paper presents a summary of principal results obtained from crossflow tests of a model 15-in.-diam lift fan installed in a wing in the NASA Lewis Research Center, 9 by 15 ft V/STOL Propulsion Wind Tunnel. Tests were run with and without exit louvers over a range of tunnel air speeds, fan speeds, and wing angle of attack. Fan thrust in crossflow was influenced by two principal factors: the effects of inflow distortion on blade-row performance, and changes in fan stage operating point brought about by changes in back pressure ratio. In this particular fan, flow separation on the inlet bellmouth did not appear to be a serious problem for crossflow operation.

Lieblein, S.↗
NASA NTRS1972

A prediction model for lift-fan simulator performance

The performance characteristics of a model VTOL lift-fan simulator installed in a two-dimensional wing are presented. The lift-fan simulator consisted of a 15-inch diameter fan driven by a turbine contained in the fan hub. The performance of the lift-fan simulator was measured in two ways: (1) the calculated momentum thrust of the fan and turbine (total thrust loading), and (2) the axial-force measured on a load cell force balance (axial-force loading). Tests were conducted over a wide range of crossflow velocities, corrected tip speeds, and wing angle of attack. A prediction modeling technique was developed to help in analyzing the performance characteristics of lift-fan simulators. A multiple linear regression analysis technique is presented which calculates prediction model equations for the dependent variables.

Yuska, J. A.↗
NASA NTRS1972

Fan and wing force data from wind tunnel investigation of a 0.38 meter (15 inch) diameter VTOL model lift fan installed in a two dimensional wing

Test data are presented for a 38-cm (15-in.) diameter, 1.28 pressure ratio model VTOL lift fan installed in a two-dimensional wing and tested in a 2.74-by 4.58-meter (9-by 15-ft)V/STOL wind tunnel. Tests were run with and without exit louvers over a wide range of crossflow velocities and wing angle of attack. Tests were also performed with annular-inlet vanes, inlet bell-mouth surface disconuities, and fences to induce fan windmilling. Data are presented on the axial force of the fan assembly and overall wing forces and moments as measured on force balances for various static and crossflow test conditions. Midspan wing surface pressure coefficient data are also given.

Yuska, J. A.↗
NASA NTRS1968

Description and Flight Performance Results of the WASP Sounding Rocket

A general description of the design and construction of the WASP sounding rocket and of the performance of its first flight are presented. The purpose of the flight test was to place the 862-pound (391-kg) spacecraft above 250 000 feet (76.25 km) on free-fall trajectory for at least 6 minutes in order to study the effect of "weightlessness" on a slosh dynamics experiment. The WASP sounding rocket fulfilled its intended mission requirements. The sounding rocket approximately followed a nominal trajectory. The payload was in free fall above 250 000 feet (76.25 km) for 6.5 minutes and reached an apogee altitude of 134 nautical miles (248 km). Flight data including velocity, altitude, acceleration, roll rate, and angle of attack are discussed and compared to nominal performance calculations. The effect of residual burning of the second stage motor is analyzed. The flight vibration environment is presented and analyzed, including root mean square (RMS) and power spectral density analysis.

De Pauw, J. F.↗