Search NASA⌕ Search

Engineering topics

Zabriskie, Adam X

Publications and source records attributed to Zabriskie, Adam X.

Streaming in a Nuclear Grade Sandwich Composite for Microreactor Shielding

The NGSC is a new approach to develop a shield structure for microreactors which combines the biological shielding with the reactor pressure vessel. Six layers of SS316 skins and core materials are present in the NGSC, where the core materials are reduce the neutron and gamma dose. Previous work has examined how a simplified NGSC can be optimized for cost, dose, and weight. This work explored the inclusion of SS36 ribs, which helps maintain the structural integrity of the NGSC, affects the transportation of radiation through the NGSC. For B$_4$C layers, the addition of ribs reduces neutron absorption but increase photon absorption. For WB$_4$-cermet layers, the addition of ribs reduces neutron absorption and reduces photon absorption.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Mass Optimization of a Multilayered Shield for Transportable Microreactors

The ability to easily transport microreactors is a major selling point for deploying microreactors to remote areas. However, this creates a unique shielding challenge, especially when the microreactor is being shipped after irradiation. A traditional reactor configuration utilizes a separate biological shield and pressure vessel to meet radiological shielding and pressure needs. The limited space available for transportable microreactors for both shielding and pressure vessels requires a revised assessment of separating out the biological shield and pressure vessel. To address these concerns, we examine a nuclear-grade sandwich composite (NGSC) that combines the reactor pressure vessel and biological shielding functions into a single component. Through a series of optimization problems for both transportation and operational use cases, the NGSC is able to minimize dose, minimize the vessel cost, and ensure that weight requirements are met for transportation. Initial results show that using a tungsten-tetraboride cermet in the first two layers of a six-layer NGSC provides adequate shielding for both use cases. These results show promise that an NGSC has enough overlap between operational and transportation cases to help reduce the design space for future analysis and assessment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Bison Analyses of Fuel Forms used in Small Modular Reactors

Small Modular Reactors (SMRs) are actively being pursued by the international nuclear industry. The Bison fuel performance code developed at Idaho National Laboratory is a tool capable of analyzing the thermo-mechanical response and species diffusion for a wide variety of fuel types under both normal and accident conditions. Two of the fuel types considered for a wide range of SMRs are TRISO fuel particles and metallic fuel. This paper provides an overview of the capabilities in Bison for these fuel types with a few example studies relevant for the SMR industry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary Analysis of a Nuclear Grade Sandwich Composite for Transportable Micro-Reactor Shielding

Transportable microreactors pose a unique shielding challenge compared with conventional reactors. Many vendors are seeking to transport a microreactor to a site, operate it for a number of years, and then transport it to a secondary site. This involves ensuring the reactor has sufficient shielding during operations and post-irradiation transportation to ensure the safety of those around it, all while ensuring it can be transported via traditional means. This work examines the use of a nuclear grade sandwich composite (NGSC) which seeks to combine the reactor pressure vessel and biological shielding into a single unit. Through this work, it was determined that the NGSC was sufficient to adequately reduce neutron and gamma current exiting the structure to warrant further investigation as a potential shielding option for microreactors.

42 ENGINEERING↗

Modeling Internal Material Melting

The purpose of the SEED LDRD was to create new functionality to model internal material melting and solidification inside the state-of-the-art nuclear fuel performance simulation code BISON.

97 MATHEMATICS AND COMPUTING↗

Transient Analysis of a Micro-reactor using the DireWolf Code Suite

Transient analyses of heat pipe micro-reactors are necessary to ensure that hypothetical accident scenarios do not comprise reactor safety. Due to its small size and reliance on heat-pipes for cooling, the micro-reactor design introduced in this paper is a tightly coupled system which requires multi-physics tools to accurately model transient events. Idaho National Laboratory’s DireWolf code suite based on the MOOSE framework is tailor-built to model heat-pipe reactors. This paper demonstrates DireWolf’s ability to simulate the coupled thermal-neutronics transient behavior of a heat-pipe micro-reactor. The transient events presented here include an inadvertent rotation of all control drums simultaneously and a sudden complete ejection of a single control drum. A detailed description of each event is provided along with simulation results, including time dependent power and temperature distributions, and discussion. This is a Westinghouse Electric Company (WEC) led publication.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Modeling and Analysis of a Micro-reactor using the DireWolf Code Suite

Micro-reactors, specifically those cooled with heat pipes, are tightly coupled systems which require multi-physics tools to accurately model both steady-state and transient behavior. Idaho National Laboratory’s DireWolf code suite is tailor-built to model heat-pipe reactors. DireWolf’s ability to model the coupled steady-state behavior of a heat-pipe micro-reactor are demonstrated herein. The DireWolf modeling methodology is described, and a micro-reactor design is introduced. A full-core model is developed, and the steady-state coupled neutronics-thermal analysis is performed. Results of the analyses, including flux, power, and temperature distributions are presented and discussed. This is a Westinghouse Electric Company (WEC) led publication.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Impact of Grain Size on Performance Degradation of TREAT LEU

We argue that radiation damage induced degradation of thermal conductivity does not set a lower limit on fuel grain sizes for the low enriched uranium fuel design of the Transient Reactor Test Facility (TREAT). Earlier work reports that smaller grains cause a larger degradation of thermal conductivity than larger grains constraining the smallest feasible size of fuel grains. This work assesses TREAT’s transient performance in the presence of radiation damage. The difference between the two studies is in treating damaged and fresh graphite as serial (this work) or parallel (previous) heat resistors. We use a multiphysics model of TREAT fuel grains to compute the reduction in transient capability measured by the total deposited energy as a function of irradiation dose. We find that radiation damage has a negligible effect on energy deposition.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Select Transient Metallic Fuel Bison Benchmarks

To explore the current capabilities of Bison with respect to transient metallic fuel modeling, four transient experiments are compared with their respective Bison model. The four experiments are the OPT-1 experiment of the Experimental Breeder Reactor II~(EBR-II) and the M5, M6, and M7 experiments of the Transient Reactor Test facility (TREAT). Each benchmark is a 2D-RZ geometry of a single pin employing coupled multiphysics. Bison models of the benchmark agree well and illustrate areas needing development. The areas of suggested development deal with better material models, better coolant channel module for transients, proper treatment of material melting, improved feedback with failure models, and an ability to set initial conditions from post irradiation examination (PIE) data. Two Fast Flux Test Facility (FFTF) pins are also modeled with M7 transient conditions to illustrate Bison being applied to investigate potential experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient Multiphysics with MAMMOTH and Bison

This is a poster for the Young Research Association poster presentation happening July 19 in EROB. The poster is about my PhD research and my internship project.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Performance Prediction of Irradiated TREAT Fuel

Poster Title: Performance Prediction of Irradiated TREAT Fuel The poster presents findings about the irradiation damage layer effects on the microscopic fuel temperature profile in TREAT. Microscopic fuel particles in TREAT are small enough that fission fragments travel out of the particles causing thermal property reduction in a shell around the fuel particle. The use of Magpie and MAMMOTH code is illustrated. The thermal temperature solution is simulated using EOS pulse power data. The reduction of microscopic fuel particle size reduced the irradiation damage due to fission fragments. The reduction of fission events is shown to be greater than the increase in fission fragments leaving the particle as size decreases. The temperature difference between the microscopic fuel particle and bulk graphite is shown to increase with irradiation as the damage layer grows.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Summary and Assessment of Metal Fuel Capabilities in Bison

The work described in this report was performed under funding from the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. This report is issued in satisfaction of the level 2 milestone M2MS-18IN0201012 on Release Bison with Initial Metallic Fuel Performance Capability. Metallic fuel development began in Bison a few years after light water reactor development began (~ 2009). The initial development was funded by the Advanced Fuels Campaign. With recent interest from industry, the Nuclear Regulatory Commission, and the Versatile Test Reactor program, the Nuclear Energy Modeling Simulation Program has increased funding for metallic fuel development and validation in FY18. The material models with the most mature development are binary uranium-zirconium and ternary uranium-plutonium-zirconium alloys for fuel and HT9 for cladding. The first material models were incorporated from open literature sources, which include mechanical and thermal material properties that are functions of temperature, porosity, and zirconium concentration, swelling, fission gas release, zirconium diffusion, creep, and sodium coolant channel boundary conditions. These material models have been utilized to simulate ERB-II fuel pins and the results compared to measurements. The EBR-II experiment measurements mostly consist of cladding strain and zirconium redistribution. As such, comparisons to EBR-II measurements are currently limited to these two figures of merit. Simulations and comparisons to experiment measurements have also been done for transient testing of EBR- II fuel pins in TREAT, which included temperature measurements. Preliminary comparisons between Bison calculations and experiment measurements are favorable. These comparisons have also highlighted the importance of the fuel swelling and fission gas release models on cladding strain. Also, Bison metallic fuel simulations are currently being run in support of ATR experiments and VTR exploratory design calculations. Further development and evaluation of individual material models and fuel system models are planned for FY19.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗