Search NASA⌕ Search

Engineering topics

Zalesak, J.

Publications and source records attributed to Zalesak, J..

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Application of NASTRAN to large space structures

The application of NASTRAN to design studies of two very large-area lightweight structures is described. The first is the Satellite Solar Power Station, while the second is a deployable three hundred meter diameter antenna. A brief discussion of the operation of the SSPS is given, followed by a description of the structure. The use of the NASTRAN program for static, vibration and thermal analysis is illustrated and some results are given. Next, the deployable antenna is discussed and the use of NASTRAN for static analysis, buckling analysis and vibration analysis is detailed.

Balderes, T.↗
NASA NTRS1975

Shuttle wing panel stability analysis

The use of the NASTRAN program in the shuttle wing stability analysis is described, and details of the actual structure, the finite element idealization, and the NASTRAN results are given. A comparison of the NASTRAN results with those obtained with another computer program and with hand generated results indicates good agreement. An alternate approach for solving eigenvalue problems is illustrated and shows a considerable savings in computer time. Some emphasis is placed on the relationship of the NASTRAN analysis in the design process bringing out more clearly the contribution of the results and showing the importance of the mode plots. A deficiency in the NASTRAN plate elements when used to model structures made up of intersecting plates is discussed.

Balderes, T.↗
NASA NTRS1975

Modal coupling procedures adapted to NASTRAN analysis of the 1/8-scale shuttle structural dynamics model. Volume 1: Technical report

A dynamic substructuring analysis, utilizing the component modes technique, of the 1/8 scale space shuttle orbiter finite element model is presented. The analysis was accomplished in 3 phases, using NASTRAN RIGID FORMAT 3, with appropriate Alters, on the IBM 360-370. The orbiter was divided into 5 substructures, each of which was reduced to interface degrees of freedom and generalized normal modes. The reduced substructures were coupled to yield the first 23 symmetric free-free orbiter modes, and the eigenvectors in the original grid point degree of freedom lineup were recovered. A comparison was made with an analysis which was performed with the same model using the direct coordinate elimination approach. Eigenvalues were extracted using the inverse power method.

Zalesak, J.↗
NASA NTRS1974

Development of technology for fluid-structure interaction modeling of a 1/8-scale dynamic model of shuttle External Tank (ET). Volume i: Technical report

A NASTRAN analysis of the external tank (ET) substructure of the 1/8-scale space shuttle structural dynamics model is described. The NASTRAN hydroelastic procedures were used to form a model of the liquid oxygen portion of the ET. Large computer storage requirements and running times were required unless these procedures were modified. Several possibilities were demonstrated including the substitution of the real for the complex eigenvalue routine and the use of the OMIT capability to reduce the number of fluid coordinates. A NASTRAN model of the complete ET was formed and reduced to 252 degrees of freedom. A review of the eigenvector extracted, using the unsymmetrical inverse power method, indicated that the structural OMIT's resulted in unsatisfactory modal deflections. Modifications to the NASTRAN hydroelastic capability appeared necessary to generate a successful ET model. An approach is described which, by assuming incompressibility, reduces the fluid representation to a symmetric mass matrix which can be added to the structural mass. The problem is solved using faster and more efficient eigenvalue routines. Using this approach the ET NASTRAN model was analyzed for three separate weight conditions.

Bernstein, M.↗
NASA NTRS1974

Development of technology for modeling of a 1/8-scale dynamic model of the shuttle Solid Rocket Booster (SRB)

A NASTRAN analysis of the solid rocket booster (SRB) substructure of the space shuttle 1/8-scale structural dynamics model. The NASTRAN finite element modeling capability was first used to formulate a model of a cylinder 10 in. radius by a 200 in. length to investigate the accuracy and adequacy of the proposed grid point spacing. Results were compared with a shell analysis and demonstrated relatively accurate results for NASTRAN for the lower modes, which were of primary interest. A finite element model of the full SRB was then formed using CQUAD2 plate elements containing membrane and bending stiffness and CBAR offset bar elements to represent the longerons and frames. Three layers of three-dimensional CHEXAI elements were used to model the propellant. This model, consisting of 4000 degrees of freedom (DOF) initially, was reduced to 176 DOF using Guyan reduction. The model was then submitted for complex Eigenvalue analysis. After experiencing considerable difficulty with attempts to run the complete model, it was split into two substructres. These were run separately and combined into a single 116 degree of freedom A set which was successfully run. Results are reported.

Levy, A.↗
NASA NTRS1974

Analytical and experimental investigation of a 1/8-scale dynamic model of the shuttle orbiter. Volume 3B: Supporting data

The NASA Structural Analysis System (NASTRAN) Model 1 finite element idealization, input data, and detailed analytical results are presented. The data presented include: substructuring analysis for normal modes, plots of member data, plots of symmetric free-free modes, plots of antisymmetric free-free modes, analysis of the wing, analysis of the cargo doors, analysis of the payload, and analysis of the orbiter.

Mason, P. W.↗
NASA NTRS1974

Analytical and experimental investigation of a 1/8-scale dynamic model of the shuttle orbiter. Volume 1: Summary report

A 1/8-scale structural dynamics model of the space shuttle orbiter was analyzed using the NASA Structural Analysis System (NASTRAN). Comparison of the calculated eigenvalues with preliminary test data for the unrestrained condition indicate that the analytical model was consistently stiffer, being about 20% higher in the first mode. The eigenvectors show reasonably good agreement with test data. A series of analytical and experimental investigations undertaken to resolve the discrepancy are described. Modifications in the NASTRAN model based upon these investigations resulted in close agreement for both eigenvalues and eigenvectors.

Mason, P. W.↗
NASA NTRS1973

NASTRAN analysis of the 1/8-scale space shuttle dynamic model

The space shuttle configuration has more complex structural dynamic characteristics than previous launch vehicles primarily because of the high model density at low frequencies and the high degree of coupling between the lateral and longitudinal motions. An accurate analytical representation of these characteristics is a primary means for treating structural dynamics problems during the design phase of the shuttle program. The 1/8-scale model program was developed to explore the adequacy of available analytical modeling technology and to provide the means for investigating problems which are more readily treated experimentally. The basic objectives of the 1/8-scale model program are: (1) to provide early verification of analytical modeling procedures on a shuttle-like structure, (2) to demonstrate important vehicle dynamic characteristics of a typical shuttle design, (3) to disclose any previously unanticipated structural dynamic characteristics, and (4) to provide for development and demonstration of cost effective prototype testing procedures.

Bernstein, M.↗