Search NASA⌕ Search

Engineering topics

Zang, Q.

Publications and source records attributed to Zang, Q..

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Electron ITB formation in EAST high poloidal beta plasmas under dominant electron heating

Abstract Plasma confinement and transport in tokamaks play a crucial role in the development of high poloidal beta steady-state operation scenarios. Therefore, it is very important to study the relevant mechanism of internal transport barriers (ITBs), which can help plasmas to obtain better confinement in order to achieve higher fusion gain. This paper mainly introduces the analysis of the characteristics of electron heat transport of discharges with ITB in high β P operation regime in Experimental Advanced Superconducting Tokamak (EAST). Based on the statistical analysis of stable discharges with β P > 1.5, it is found that there is an obvious bifurcation of the normalised electron temperature gradient (ETG) ( R / L T e ) in the range of β P = 2–2.2. Then the discharges of lower β P ( β P < 2, where the value of β P is below the bifurcation threshold) and of higher β P ( β P > 2.2, where the value of β P is above the threshold) were selected for analysis. The diagnostic data provided by Thomson scattering, x-ray crystal spectrometry and charge exchange recombination spectroscopy are used to provide reliable parameter profiles and then combined with the data of external magnetic probe measurements and the polarisation interferometer diagnosis system to fully reconstruct the balance. A relevant plasma current calculation model is used to calculate and analyse the current density profiles and power deposition, and then the transport analysis is carried out. Interestingly, in the higher β P discharges, it is found that the turbulence intensity provided by the CO 2 laser collective scattering system gradually decreases and the normalised ETG R / L T e gradually increases. It is also found that the electron heat transport coefficient decreases in the discharge with higher β P and the growth rate of the electron-scale turbulence calculated by transport gyro-Landau fluid (TGLF) is significantly reduced. Meanwhile, similar conclusions are also obtained in the discharges when the β P is further increased.

Wang, Z. H. (ORCID:0009000203431036)↗
DOE OSTI2023

Long-pulse high-performance H-mode plasmas achieved on EAST

A record duration of a 310 s H-mode plasma (H 98y2 ~ 1.3, n e /n GW ~ 0.7, f BS > 50%) has been recently achieved on experimental advanced superconducting tokamak (EAST) with metal walls, exploiting the device's improved long-pulse capabilities. The experiment demonstrates good control of tungsten concentration, core/edge MHD stability, and particle and heat exhaust with an ITER-like tungsten divertor and zero injected torque, establishing a milestone on the path to steady-state long-pulse high-performance scenarios in support of ITER and CFETR. Important synergistic effects are leveraged toward this result, which relies purely on radio frequency (RF) powers for heating and current drive (H&CD). On-axis electron cyclotron heating enhances the H&CD efficiency from lower hybrid wave injection, increasing confinement quality and enabling fully non-inductive operation at high density (n e /n GW ~ 70%) and high poloidal beta (β P ~ 2.5). A small-amplitude grassy edge localized mode regime facilitates the RF power coupling to the H-mode edge and reduces divertor sputtering/erosion. The high energy confinement quality (H 98y2 ~ 1.3) is achieved with the experimental and simulated results pointing to the strong effect of Shafranov shift on turbulence. Transport analysis suggests that trapped electron modes dominate in the core region during the record discharge. The detailed physics processes (RF synergy, core-edge integration, confinement properties, etc.) of the steady-state operation will be illustrated in the content. In the future, EAST will aim at accessing more relevant dimensionless parameters to develop long-pulse high-performance plasma toward ITER and CFETR steady-state advanced operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Resonant mode effects on rotation braking induced by n = 1 resonant magnetic perturbations in the EAST tokamak

Abstract The spectrum effects on toroidal rotation braking, induced by n = 1 resonant magnetic perturbations (RMPs) in the discharges with q 95 = 4.1 and q 95 = 5.1 , are studied in the EAST tokamak. Here n is the toroidal mode number, RMP spectrum is varied by scanning δ ϕ U L , the phase difference between the upper and lower rows of RMP coils. The toroidal rotation changes periodically with the periodic δ ϕ U L scanning and such an effect is stronger in the discharge with lower q 95 = 4.1 . The spectrum dependence of the neoclassical toroidal viscosity (NTV) torque, modeled by NTVTOK based on the magnetic perturbation obtained from MARS-F calculation, agrees well with that of the experimentally observed braking torques in both discharges. The modeled NTV torque is stronger in the discharge with lower q 95 , which also agrees with the observations. The comparisons between the spectrum dependence of the NTV and magnetic perturbations show that the resonant mode of magnetic perturbations near the plasma edge mainly contribute the NTV torque. These agreements between modeling and experiments highlight the capability of NTV theory in explaining the experimental observation in the EAST tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Plasma heating by electron cyclotron wave and the temperature effects on lower hybrid current drive on EAST

This paper presents the progress in the long—pulse operation of the electron cyclotron (EC) system and the achievements in high—electron temperature plasmas by the combined EC and lower hybrid (LH) waves heating since the EC system was built in 2015. An electron temperature of up to 12 keV with a duration over 100 s was realized by the simultaneous heating of EC and LH waves at the line-averaged density ${\bar n_{\text{e}}}$ ~1.8 × 10 19 m –3 . The plasma heating effect strongly depends on the location of EC power deposition. H-mode plasmas with solely EC wave auxiliary heating have been obtained on EAST for the first time. These H-mode discharges show an enhanced confinement factor H 98(y,2) around 1.0, which is higher than the previous H-mode using LH power alone (Xu et al 2011 Nucl. Fusion 51 072001). The total heating power is very close to the threshold value for L–H transition according to the international tokamak scaling. In addition to the temperature effects inside the separatrix, higher electron temperature produced by EC wave is found to reduce the LH power loss in the scrape-off layer due to collisional absorption, which is beneficial to further increase the LH current drive efficiency. Ray-tracing/Fokker–Planck modeling results indicate that higher electron temperature can shorten the LH wave propagation on EAST in a multiple-pass regime, thus decreasing the collisional dissipation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Observation and analysis of lower-hybrid-current-drive density limit in EAST

Lower hybrid current drive (LHCD) experiments with line-averaged density up to ~5.1 × 10 19 m –3 were performed in EAST L-mode plasmas. When the line-averaged density rises above a critical value, the hard x-ray (HXR) emission falls to the noise level, indicating that the LHCD density limit is encountered. The experimental results show that the LHCD density limit can be increased with higher wave source frequency (ƒ 0 ) and higher magnetic field (B t ). Although a higher LHCD density limit is obtained by a higher magnetic field for both 2.45 GHz and 4.6 GHz waves, the results show a stronger dependence on the magnetic field for the 4.6 GHz case. Analysis suggests that, for normal operation with a relatively low magnetic field (1.6 T $\leqslant$ B t $\leqslant$ 2.5 T) on EAST, the dominant mechanisms responsible for the LHCD density limit are different between the 2.45 GHz and 4.6 GHz waves. The wave accessibility plays a more significant role during 4.6 GHz LHCD experiments, while parasitic losses due to parametric decay instability (PDIs) dominate the accessibility issue in the 2.45 GHz case. Collisional loss in the scrape-off layer (SOL) may explain the 4.6 GHz result when combined with the accessibility limit at high density and low temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Characterization of beam ion loss in high poloidal beta regime on EAST

A critical issue for achieving the integrated operation of steady-state long-pulse high-confinement (H-mode) plasmas on experimental advanced superconducting tokamak (EAST) is to improve beam ion population confinement during neutral beam injection (NBI). To study the characterization of beam ion loss and improve beam ion confinement, the steady-state long pulse scenario discharges were conducted on EAST (β p $\geqslant$ 2.0, β N $\geqslant$ 1.7, q 95 $\geqslant$ 6.7 and H 98y2 $\geqslant$ 1.1) with NBI heating. Based on neutron yield, the beam voltage and line-averaged electron density were adjusted from 50 kV to 60 kV and 4.4 × 10 19 m –3 to 5.0 × 10 19 m –3 , respectively. The results show that the dominant mechanisms of beam ion loss are shine-through loss, prompt loss, and stochastic ripple loss. The shine-through loss fraction is determined by initial velocity, flight time and entire beam path. The change in prompt loss fraction is caused by the change in the deposition of beam ions. The change in stochastic ripple loss fraction is caused by the change in the initial fraction of trapped-confined ions. Detailed physics shows that the prompt loss fraction during counter-Ip injections (~45%) is far larger than during co-Ip injections (~5%) due to the finite orbit width. The lost ions are mainly deposited on the lower divertor or below the midplane since the direction of magnetic drift is vertical down. The orbit types of prompt loss during counter-Ip injections are mainly trapped-lost and ctr-passing lost. To minimize the prompt loss fraction during counter-Ip injections, a reversed Ip configuration (rev-Ip) discharge #94758 was conducted. The result suggests that the beam ion wall load fraction during counter-Ip tangential injection (~3%) is far lower than that in normal Ip configuration (nor-Ip) discharge #94820. It is also found that the confinement of beam ion population in the counter-Ip injection #94758 was greatly improved when compared to #94820. Finally, this study can provide unique support for the improvement of beam ion population confinement and for the performance evaluation of the NBI system on EAST and future tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Experimental and theoretical study of weakly coherent mode in I-mode edge plasmas in the EAST tokamak

The I-mode is a promising operation mode for fusion in the future, featuring high-temperature and low-density confinement, but the reason why the temperature and density are decoupled remains an important aspect to be explored. The experimental results from the experimental advanced superconducting tokamak (EAST) showed that the weakly coherent mode (WCM) is directly related to sustaining the I-mode and that the peak amplitude of the WCM is proportional to the temperature in the pedestal. Here, simulating the experimental data from EAST with the six-field model of BOUT++, we find a density perturbation close to the frequency of the WCM observed in the experiment. By testing all the physical terms in this model, we find that the density perturbation and particle transport are directly related to the drift Alfvén wave (DAW) mode. Additionally we use the SymPIC program (Xiao et al Plasma Sci. Technol. 20 110501; Phys. Plasmas 22 112504; Plasma Sci. Technol. 23 055102) to simulate the same experimental data and find that the frequency range of the WCM is close to both experimental and BOUT++ results. Therefore, the WCM of the I-mode can be considered to be driven by the DAW, which helps improve the transport of the I-mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Impact of lithium wall conditioning and wave-frequency on high density lower hybrid current drive experiment on EAST

A series of dedicated lower hybrid current drive (LHCD) experiments on EAST shows that lithium wall conditioning extends LH current drive and heating up to the line-averaged density of n ̅_e≈ 4x1019 m-3 for both 2.45 and 4.6 GHz. Current drive at such a high density is crucial for the development of long-pulse non-inductive scenarios on EAST. With lithiation, the LH power injection of 1.5 MW at 2.45 GHz resulted in a drop of loop voltage of ~ 0.3 V, which is a comparable loop voltage drop observed with 1.1 MW at 4.6 GHz. The observed decrease in loop voltage is attributed mostly to the RF heating effect. Another LHCD experiment suggests that lithium wall coating has a more significant impact on the scrape-off-layer (SOL) properties than changes in the Greenwald fraction. LHCD at 2.45 GHz still suffers from a loss of efficiency. Enhanced power ionization in front of the launcher may cause the onset of density-dependent wave instabilities. The rise in the midplane SOL density may also accelerate a transition in the divertor regime, leading to additional ionization and collisional losses in the X-point divertor plasma. Ray-tracing modeling supports that a lower wave frequency is more prone to collisional power loss. The experiments confirm that lithiation is a useful tool to control the SOL plasma, and suggest that density control in front of the launcher may be critical to mitigating power loss mechanisms in the plasma boundary.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Physical mechanisms for the transition from type-III to large ELMs induced by impurity injection on EAST

Transition from type-III to large-amplitude ELMs induced by neon injection has been observed in the EAST tokamak at overlapping q 95 space between large and small ELMs. With neon injection, pedestal density gradient shows a remarkable increase accompanied by some decrease of pedestal electron temperature, and consequently the pressure gradient increases moderately and edge bootstrap current has minimal change. Further experiment demonstrates that the occurrence of large ELMs after neon injection is highly correlated with the change in edge density. Linear peeling-ballooning stability analysis indicates that the large ELM case is more unstable than the type-III ELM case during the ELM transition. A scan of pedestal density gradient in linear stability analysis shows that the direct destabilizing effect of steep pedestal density gradient on peeling-ballooning instabilities via two-fluid effects could also facilitate the transition to large ELMs. In conclusion, these results could provide more insight into the role of pedestal density gradient on pedestal stability and ELM behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Theoretical analysis of key factors achieving reversed magnetic shear q-profiles sustained with lower hybrid waves on EAST

The phase space analysis technique is applied to provide new insights into the fully non-inductive lower hybrid current driven (LHCD) discharges on EAST (Garofalo et al 2017 Nucl. Fusion 57 076037). The analysis shows that there are bounded and unbounded topologies of lower hybrid (LH) waves in phase space. For typical parameters on EAST, the propagation domain for 4.6 GHz LH waves is bounded, while unbounded for 2.45 GHz LH waves and one of the conditions is recognized to be good for achieving an off-axis current profile driven by 4.6 GHz LH waves on EAST. The parametric analysis on the potential power deposition (PPD) region for those experiments demonstrates that the reversed magnetic shear dominates the wave behavior, and confines the LH power absorption to the far off-axis region as long as it occurs in the 4.6 GHz dominated LHCD discharge. GENRAY/CQL3D simulations also confirm this effect of reversed shear on the power absorption of 4.6 GHz waves. A bounded propagation domain and a positive feedback loop between magnetic shear reversal and off-axis LHCD profile could explain the LH-only-sustained strong reversed magnetic shear observed in experiments on multiple machines. In contrast, there is no such effect for 2.45 GHz waves on EAST since the PPD region is less sensitive to the change of reversed shear due to the unbounded propagation domain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Type-I ELM mitigation by continuous lithium granule gravitational injection into the upper tungsten divertor in EAST

Large edge-localized modes (ELMs) were mitigated by gravitational injection of lithium granules into the upper X-point region of the experimental advanced superconducting tokamak (EAST) device with tungsten plasma-facing components. The maximum ELM size was reduced by ~70% in high β N H-mode plasmas. Large ELM stabilization was sustained for up to about 40 energy confinement times, with constant core radiated power and no evidence of high-Z or low-Z impurity accumulation. The lithium granules injection reduced the edge plasma pedestal density and temperature and their gradients, due to increased edge radiation and reduced recycling from the plasma-facing components. Ideal stability calculations using the ELITE code indicate that the stabilization of large ELMs correlates with improved stability of intermediate-n peeling-ballooning modes, due to reduced edge current resulting from the profile changes. The pedestal pressure reduction was partially offset by a core density increase, which resulted in a modest ~7% drop in core stored energy and normalized energy confinement time. We surmise that the remnant small ELMs are triggered by the penetration of multiple Li granules just past the separatrix, similar to small ELMs triggered by deuterium pellet Futatani et al (2014 Nucl. Fusion 54 073008). This study extends previous ELM elimination with Li powder injection Maingi et al (2018 Nucl. Fusion 58 024003) in EAST because (1) use of small, dust-like powder and the related potential health hazards were eliminated, and (2) use of macroscopic granules should be more applicable to future devices, due to deeper penetration than dust particles, e.g. inside the separatrix with velocities ~10 m s -1 in EAST.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Advances in physics understanding of high poloidal beta regime toward steady-state operation of CFETR

Experimental and modeling investigations of the high βp scenarios on the DIII-D and EAST tokamaks show advantages in high energy confinement, avoidance of n = 1 MHD, and core-edge integration with reduced heat flux, making this scenario an attractive option for CFETR steady-state operation. Experiments show that plasmas with high confinement and high density can be achieved with neutral beam injection on DIII-D (β p ~ 2.2, β N ~ 3.5, f BS ~ 50%, f Gw ~ 1.0, H 98y2 ~ 1.5) and pure RF power on EAST (β P ~ 2.0, β N ~ 1.6, f BS ~ 50%, f Gw ~ 0.8, H 98y2 > 1.3). By tailoring the current density profile, a q-profile with local (off-axis) negative shear is achieved that yields improved confinement and MHD stability. Transport analysis and simulation suggest that the combination of high density gradient and high Shafranov shift allows turbulence stabilization and higher confinement. Using on-axis ECH injection, tungsten accumulation is avoided on EAST, and this is reproduced in modeling. Reduced heat flux (by >40%) and maintenance of high core confinement is achieved with active feedback control of the radiated divertor, an important result for long pulse operation in tokamaks. In conclusion, the improved physics understanding and validated modeling tools are used to design a 1GW steady-state scenario for CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Suppression of edge localized modes with real-time boron injection using the tungsten divertor in EAST

We report an observation of robust suppression of edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST), enabled by continuous boron (B) powder injection. Edge harmonic oscillations appear during B powder injection, providing sufficient particle transport to maintain constant density and avoid impurity accumulation in ELM-stable plasmas. Here, quasi-steady ELM suppression discharges are demonstrated with modest energy confinement improvement and over a wide range of conditions: heating power and technique variation, electron density range over a factor ~3.5, deuterium or helium ion species, and with either direction of the toroidal magnetic field. ELM suppression is observed above a threshold edge B intensity and ceases within 0.5 s of termination of the B injection. In contrast to ELM suppression accompanied by recycling reduction during Li powder injection in NSTX and EAST (Maingi et al 2018 Nucl. Fusion 58 024003), reduced recycling due to hydrogenic species retention is unnecessary for the ELM suppression with B powder injection, paving the way for its consideration as an ELM control tool for future fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Experimental study of high-k turbulence during an energy confinement degradation phase in EAST ohmic plasmas

In this paper, we present experimental studies of both high-k(r) ( cm(-1), and , respectively; ) and high- ( cm(-1), and , respectively; ) turbulence behavior during an ohmic energy confinement degradation phase in experimental advanced superconducting tokamak (EAST). High-k(r) turbulence from density fluctuation at and high- turbulence from density fluctuation at -0.97 were measured by tangential and poloidal CO2 laser collective scattering diagnostics, respectively. Note that k(r), , and are radial wavenumber, poloidal wavenumber, perpendicular wavenumber and ion gyroradius at electron temperature, respectively. Both high-k(r)/ turbulence power and energy confinement time are found to be temporally correlated to line-averaged electron density n(e) in the plasma current flat-top phase (I-p = 0.4 MA): when the n(e) shows continuous increase/decrease, the high-k(r)/ turbulence power increases/decreases correspondingly and the shows corresponding decrease/increase; the stable n(e) is related to stable both and high-k(r)/ turbulence power. Statistical results of high-k(r)/ turbulence power versus further imply that high-k(r)/ turbulence shows a strong correlation with plasma energy confinement degradation in high line-averaged n(e) condition, but high-k(r) and high- turbulence have relatively weak and no dependence on the transition between linear range in low-n(e) condition and energy confinement degradation in the high-n(e) condition, respectively. Moreover, profiles of electron temperature T-e and n(e) as well as their normalized gradients in a part of high- density fluctuation measurement region also have been given to qualitatively explain the enhancement of turbulence power with the increase of line-averaged n(e).

EAST tokamak↗
DOE OSTI2020

Stabilizing effect of enhanced resistivity on peeling-ballooning instabilities on EAST

Previous stability analysis of NSTX equilibrium with lithium-conditioning demonstrates that enhanced resistivity due to the increased effective charge number Z eff (i.e. increased impurity level) can provide a stabilizing effect on low-n edge localized modes. This paper extends the resistivity stabilizing effect to the intermediate-n peeling-ballooning (PB) instabilities with the linear stability analysis of EAST high-confinement mode equilibria in NIMROD two-fluid calculations. However, in this work, the resistivity stabilizing effect on PB instabilities in the EAST tokamak appears weaker than that found in NSTX. This work may provide better insight into the physical mechanism behind the beneficial effects of impurities on pedestal stability.

EAST tokamak↗