Engineering topics

Zanganeh, Mohammad

Publications and source records attributed to Zanganeh, Mohammad.

4 records

NASA NTRS2019

A Composite Damage Tolerance Simulation Technique to Augment the Building Block Approach

Aerospace structures comprised of composite materials are traditionally certified empirically via the Building Block Approach (BBA). While this approach has been performed successfully in the past, it is expensive and time consuming. One means to improve the overall efficiency of composite structural certification is to reduce the cost of the BAA by eliminating the need for some tests by incorporating damage analysis tools. For an analysis to replace a given test, the tool must first be validated using other similar test data. The subject of this paper is a description of an analysis technique for simulating compression after damage strength of a solid laminate. The analysis technique is one that is practical for use in an applied engineering context due to efforts to minimize necessary computational resources and complexity of the model.

McElroy, Mark↗

NASA NTRS2019

A Composite Damage Tolerance Simulation Technique to Augment the Building Block Approach

Aerospace structures comprised of composite materials are traditionally certified empirically via the Building Block Approach (BBA). While this approach has been performed successfully in the past, it is expensive and time-consuming. One means to improve the overall efficiency of composite structural certification is to reduce the cost of the BBA by eliminating the need for some tests by incorporating damage analysis tools. For an analysis to replace a given test, the tool must first be validated using other similar test data. The subject of this paper is a description of an efficient analysis technique for simulating compression after damage strength of a solid laminate. The analysis technique is one that is practical for use in an applied engineering context due to efforts to minimize necessary computational resources and complexity of the model.

McElroy, Mack↗

NASA NTRS2015

Crack Instability Predictions Using a Multi-Term Approach

Present crack instability analysis for fracture critical flight hardware is normally performed using a single parameter, K(sub C), fracture toughness value obtained from standard ASTM 2D geometry test specimens made from the appropriate material. These specimens do not sufficiently match the boundary conditions and the elastic‐plastic constraint characteristics of the hardware component, and also, the crack instability of most commonly used aircraft and aerospace structural materials have some amount of stable crack growth before fracture which makes the normal use of a K(sub C) single parameter toughness value highly approximate. In the past, extensive studies have been conducted to improve the single parameter (K or J controlled) approaches by introducing parameters accounting for the geometry or in‐plane constraint effects. Using 'J‐integral' and 'A' parameter as a measure of constraint is one of the most accurate elastic‐plastic crack solutions currently available. In this work the feasibility of the J‐A approach for prediction of the crack instability was investigated first by ignoring the effects of stable crack growth i.e. using a critical J and A and second by considering the effects of stable crack growth using the corrected J‐delta a using the 'A' parameter. A broad range of initial crack lengths and a wide range of specimen geometries including C(T), M(T), ESE(T), SE(T), Double Edge Crack (DEC), Three‐Hole‐Tension (THT) and NC (crack from a notch) manufactured from Al7075 were studied. Improvements in crack instability predictions were observed compared to the other methods available in the literature.

Zanganeh, Mohammad↗

NASA NTRS2015

On the Crack Bifurcation and Fanning of Crack Growth Data

Crack growth data obtained from ASTM load shedding method for different R values show some fanning especially for aluminum alloys. It is believed by the authors and it has been shown before that the observed fanning is due to the crack bifurcation occurs in the near threshold region which is a function of intrinsic properties of the alloy. Therefore, validity of the ASTM load shedding test procedure and results is confirmed. However, this position has been argued by some experimentalists who believe the fanning is an artifact of the test procedure and thus the obtained results are invalid. It has been shown that using a special test procedure such as using compressively pre-cracked specimens will eliminate the fanning effect. Since not using the fanned data fit can result in a significantly lower calculated cyclic life, design of a component, particularly for rotorcraft and propeller systems will considerably be impacted and therefore this study is of paramount importance. In this effort both test procedures i.e. ASTM load shedding and the proposed compressive pre-cracking have been used to study the fatigue crack growth behavior of compact tension specimens made of aluminum alloy 2524-T3. Fatigue crack growth paths have been closely observed using SEM machines to investigate the effects of compression pre-cracking on the crack bifurcation behavior. The results of this study will shed a light on resolving the existing argument by better understanding of near threshold fatigue crack growth behavior.

Forman, Royce G.↗