Search NASA⌕ Search

Engineering topics

Zapol, Peter

Publications and source records attributed to Zapol, Peter.

At least 19 records

Burton-Cabrera-Frank theory for the influence of off-cut direction on the growth of hcp crystals

The precise direction of the off-cut of a vicinal crystal surface determines the azimuth (in-plane angle) of the surface steps and thus their kink density. Here we develop a Burton-Cabrera-Frank (BCF) theory for step-flow crystal growth that includes the effects of step azimuth. We focus on the basal-plane surfaces of hexagonal close-packed (hcp) and related crystal structures, for which surface steps have alternating properties that depend on azimuth. We build on a previous treatment that considered only a single-step azimuth, 𝜙 = 0, that gives alternating steps of pure A and B type. As 𝜙 increases from zero, the density of kinks on the steps increases. For hcp-type crystals, in addition the structural difference between alternating steps decreases, until they become equivalent at 𝜙 = 30°. We consider the azimuth dependence of the step transparency, attachment, and repulsion parameters of the BCF model, including the effects of both geometrically required and thermally generated kinks. Example calculations are presented that demonstrate the overall effect of step azimuth on BCF predictions for step spacings during steady-state growth and for their dynamics during growth transients. Effects of symmetric and asymmetric step-step repulsion are discussed.

Ju, Guangxu↗

Suppressing Atmospheric Degradation of Sulfide-Based Solid Electrolytes via Ultrathin Metal Oxide Layers

Sulfide-based solid-state electrolytes (SSEs) are promising materials with superior Li-ion conductivity; however, their poor atmospheric stability limits commercial manufacturing at scale. Here, we investigate the impact of ultrathin metal oxide layers deposited via atomic layer deposition (ALD) on the stability of Li 6 PS 5 Cl (LPSCl). Al 2 O 3 layers grown directly on LPSCl particles significantly stabilize the surface chemistry and Li-ion transport properties relative to uncoated material upon exposure to both an ambient atmosphere (22% relative humidity, RH) and humidified O 2 (100% RH). Detailed investigations indicate that coatings impede the surface and bulk degradation kinetics of exposed materials, even for coatings as thin as ∼1 Å. Furthermore, this suggests that stabilization is due to more than just a physical barrier. Shifts in valence band edge positions of coated LPSCl indicate that ALD coatings alter the surface electronic structure and resulting oxidation tendency of underlying LPSCl, suggesting new avenues to improving the environmental stability of sulfide SSEs.

Atmospheric chemistry↗

Comparative Analysis of Reactivity of Al and Ga Doped Garnet Solid State Electrolyte at the Interface with Li Metal

Lithium garnet (Li 7 La 3 Zr 2 O 12 , LLZO) based solid electrolytes are leading candidate materials for all-solid-state batteries with lithium metal anodes because of their high ionic conductivity, high mechanical toughness, and superior electrochemical stability. While doping LLZO with Al and Ga increases its ionic conductivity by stabilizing the cubic phase, the impact of dopants on its (electro)chemical stability at the interfaces with Li metal is critical. Here, our study of differences between Al- and Ga-doped LLZO when interfaced with lithium metal using X-ray photoelectron spectroscopy and density functional theory shows a higher propensity of Ga to move across LLZO interface with Li metal and form Ga-Li alloy. Additionally, neutron diffraction reveals loss of cubic phase resulting from the loss of dopant that explains electrochemical behavior differences between Ga- and Al-doped LLZO. Overall, our study reveals the key role of dopant chemistry in enabling stable solid electrolyte materials for all-solid-state batteries.

Klenk, Matthew↗

Entropy-Stabilized Multication Fluorides as a Conversion-Type Cathode for Li-Ion Batteries–Impact of Element Selection

Metal fluorides (e.g., FeF 2 and FeF 3 ) have received attention as conversion-type cathode materials for Li-ion batteries due to their higher theoretical capacity compared to that of common intercalation materials. However, their practical use has been hindered by low round-trip efficiency, voltage hysteresis, and capacity fading. Cation substitution has been proposed to address these challenges, and recent advancements in battery performance involve the introduction of entropy stabilization in an attempt to facilitate reversible conversion reactions by increasing configurational entropy. Building on this concept, high entropy fluorides with five cations were synthesized by using a simple mechanochemical route. In order to examine the impact of element selection, Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Fe 0.2 F 2 (HEF-Fe) was compared with Co 0.2 Cu 0.2 Ni 0.2 Zn 0.2 Mg 0.2 F 2 (HEF-Mg), replacing electrochemically inactive Mg with Fe as an active participant in the conversion reaction. Combining electrochemical measurements with first-principles calculations, high-resolution electron microscopy, and synchrotron X-ray analysis, HEFs’ battery performances and conversion reaction mechanisms were investigated in detail. The results highlighted that replacement of Mg with Fe was beneficial, with enhanced capacity, rate capability, and surface stability. In addition, it was found that HEF-Fe showed similar cycle stability without an electrochemically inactive element. In conclusion, these findings provide valuable insights for the design of high entropy multielement fluorides for improved Li-ion battery performance.

25 ENERGY STORAGE↗

Solid-state nanofiber polymer multilayer composite electrolytes and cells

A solid-state electrolyte for a multilayer solid-state electrochemical cell is described herein. The electrolyte comprises a lithium electrolyte salt and nanofibers of a cubic phase lithium lanthanum zirconium oxide (c-LLZO), and a polymer interspersed with the nanofibers and electrolyte salt. Electrochemical cells comprising the solid-state electrolyte, and solid-state cathodes comprising the nanofibers of c-LLZO are also described herein.

Zhang, Yuepeng↗

Strain-Driven Surface Reactivity in Magnesium-Ion Battery Cathodes

Successful deployment of a Mg-ion battery requires cathodes that can achieve reversible Mg intercalation and high energy density. Recent theoretical and experimental studies indicated that the overall transport is likely limited by sluggish Mg transport at the cathode-electrolyte interface and not Mg diffusion through bulk. Here, in this work, we investigated the surface electrochemical activity of Mg ions by using a spinel-structured manganese oxide thin-film model system and in situ X-ray scattering. In combination with post-mortem microscopy analysis, we found that magnesium insertion was more favorable than subsequent extraction near the surface of the Mg x Mn 2 O 4 film, resulting in overmagnesiation, and eventually amorphization of the surface. This structural irreversibility and high overpotential required for Mg extraction could explain significant voltage hysteresis and Mg surface enrichment previously observed in bulk cathodes. Density functional theory calculations suggested that the tendency for the Mg surface enrichment could be associated with Mg diffusion kinetics, which varies with the strain state evolved due to constrained film volume change during Mg insertion and extraction. Particularly, out-of-plane Mg migration was predicted to be favorable in the tensile strain rather than in the compressive case.

25 ENERGY STORAGE↗

Pulsed-Potential Electrolysis Enhances Electrochemical C–N Coupling by Reorienting Interfacial Ions

The electrochemical processing of anthropogenic CO 2 is an emerging technology aimed at utilizing renewable energies to synthesize valuable chemicals. Recently, developments in broadening the scope of the CO 2 reduction reaction (CO 2 RR) by enabling heteroatom coupling have surged with a focus on C–N bond formation. Herein, we investigate the factors that govern the selectivity and activity in synthesizing urea from environmentally malignant chemical feedstocks (CO 2 and NO 3 – ). Through a combination of electrolyte optimization and pulsed potential electrolysis, electrochemical urea production was optimized to a Faradaic efficiency of 60.4% with current densities reaching as high as 310 μA cm –2 . This work was further supported by in situ surface enhanced infrared absorbance spectroscopy that reveals the formation of C–N-related species at low overpotentials. Density functional theory calculations revealed that the reaction progresses between early reduction intermediates for the CO 2 RR and NO 3 RR and offered insights into the impacts of pulsed-potential on substrate transport.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Photoreactive Carbon Dioxide Capture by a Zirconium–Nanographene Metal–Organic Framework

Here, the mechanism of photochemical CO 2 reduction to formate by PCN-136, a Zr-based metal-organic framework (MOF) that incorporates light-harvesting nanographene ligands, has been investigated using steady-state and time-resolved spectroscopy and density functional theory (DFT) calculations. The catalysis was found to proceed via a "photoreactive capture" mechanism, where Zr-based nodes serve to capture CO 2 in the form of Zr- bicarbonates, while the nanographene ligands have a dual role of absorbing light and storing one-electron equivalents for catalysis. We also find that the process occurs via a "two-for-one" route, where a single photon initiates a cascade of electron/hydrogen atom transfers from the sacrificial donor to the CO 2 -bound MOF. The mechanistic findings obtained here illustrate several advantages of MOF-based architectures in molecular photocatalyst engineering and provide insights on ways to achieve high formate selectivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multifunctional Coatings on Sulfide‐Based Solid Electrolyte Powders with Enhanced Processability, Stability, and Performance for Solid‐State Batteries

Abstract Sulfide‐based solid‐state electrolytes (SSEs) exhibit many tantalizing properties including high ionic conductivity and favorable mechanical properties for next‐generation solid‐state batteries. Widespread adoption of these materials is hindered by their intrinsic instability under ambient conditions, which makes them difficult to process at scale, and instability at the Li||SSE and cathode||SSE interfaces, which limits cell performance and lifetime. Atomic layer deposition is leveraged to grow thin Al 2 O 3 coatings on Li 6 PS 5 Cl powders to address both issues simultaneously. These coatings can be directly grown onto Li 6 PS 5 Cl particles with negligible chemical modification of the underlying material and enable exposure of powders to pure and H 2 O‐saturated oxygen environments for ≥4 h with minimal reactivity, compared with significant degradation of the uncoated powder. Pellets fabricated from coated powders exhibit ionic conductivities up to 2× higher than those made from uncoated material, with a simultaneous decrease in electronic conductivity and significant suppression of chemical reactivity at the Li‐SSE interface. These benefits result in significantly improved room temperature cycle life at high capacity and current density. It is hypothesized that this enhanced performance derives from improved intergranular properties and improved Li metal adhesion. This work points to a completely new framework for designing active, stable, and scalable materials for next‐generation solid‐state batteries.

36 MATERIALS SCIENCE↗

Investigation of Rechargeable Calcium Metal-Selenium Batteries Enabled by Borate-Based Electrolytes

Calcium-ion batteries (CIBs) are a promising next-generation energy storage system given the low redox potential of calcium metal and high abundance of calcium compounds. For continued CIB development, the discovery of high energy density calcium ion cathodes is needed to achieve practical energy density values. Here, we report on the use of elemental Se as a promising candidate for a high-capacity cathode material for CIBs that operates via a conversion mechanism in a Ca metal battery at room temperature. The Se electrodes demonstrate a reversible specific capacity of 180 mA h g –1 with a discharge plateau near 2.0 V (vs Ca 2+ /Ca) at 100 mA g –1 using an electrolyte based on the salt calcium tetrakis(hexafluoroisopropyloxy)borate (Ca(B(hfip) 4 ) 2 ) in 1,2-dimethoxyethane (DME) and Ca metal. The reversible electrochemical reaction between calcium and selenium is investigated using operando synchrotron-based techniques and the possible reaction mechanism discussed.

25 ENERGY STORAGE↗

Oxide‐Based Solid‐State Batteries: A Perspective on Composite Cathode Architecture

Abstract The garnet‐type phase Li 7 La 3 Zr 2 O 12 (LLZO) attracts significant attention as an oxide solid electrolyte to enable safe and robust solid‐state batteries (SSBs) with potentially high energy density. However, while significant progress has been made in demonstrating compatibility with Li metal, integrating LLZO into composite cathodes remains a challenge. The current perspective focuses on the critical issues that need to be addressed to achieve the ultimate goal of an all‐solid‐state LLZO‐based battery that delivers safety, durability, and pack‐level performance characteristics that are unobtainable with state‐of‐the‐art Li‐ion batteries. This perspective complements existing reviews of solid/solid interfaces with more emphasis on understanding numerous homo‐ and heteroionic interfaces in a pure oxide‐based SSB and the various phenomena that accompany the evolution of the chemical, electrochemical, structural, morphological, and mechanical properties of those interfaces during processing and operation. Finally, the insights gained from a comprehensive literature survey of LLZO–cathode interfaces are used to guide efforts for the development of LLZO‐based SSBs.

25 ENERGY STORAGE↗

Extreme Fast Charging: Effect of Positive Electrode Material on Crosstalk

Extreme fast charging (XFC) is a key requirement for the adoption of battery-based electric vehicles by the transportation sector. However, XFC has been shown to accelerate degradation, causing the capacity, life, and safety of batteries to deteriorate. We tested cells containing five positive electrode chemistries, LFP (olivine structure), LMO (spinel), LCO (layered), NMC811 (layered) and NCA (layered), using fast-charging protocols. After testing, the negative electrodes from cells containing positive electrodes crystallizing with a layered structure were found to have more lithium deposited on their surfaces. Further, those crystallizing with a layered structure also tended to have a larger increase in impedance than those crystallizing with a spinel or olivine structure. Characterization of the negative electrodes by X-ray photoelectron spectroscopy showed that using the concentrations of LiF and Li x PO y F z as metrics, the concentration of LiF in the SEI from the cell with different positive electrodes is LFP > LMO > LCO ~ NMC811 > NCA; and for Li x PO y F z , the order is LMO > LFP > NCA > NMC811 > LCO. Clearly, the positive-electrode material was influencing the amounts of these materials formed.

25 ENERGY STORAGE↗

Investigation of Ca Insertion into α-MoO 3 Nanoparticles for High Capacity Ca-Ion Cathodes

Calcium-ion batteries (CIBs) are a promising alternative to lithium-ion batteries (LIBs) due to the low redox potential of calcium metal and high abundance of calcium compounds. Due to its layered structure, α-MoO 3 is regarded as a promising cathode host lattice. While studies have reported that α-MoO 3 can reversibly intercalate Ca ions, limited electrochemical activity has been noted, and its reaction mechanism remains unclear. Here, we re-examine Ca insertion into α-MoO 3 nanoparticles with a goal to improve reaction kinetics and clarify the storage mechanism. The α-MoO 3 electrodes demonstrated a specific capacity of 165 mA h g –1 centered near 2.7 V vs Ca 2+ /Ca, stable long-term cycling, and good rate performance at room temperature. Furthermore, this work demonstrates that, under the correct conditions, layered oxides can be a promising host material for CIBs and renews prospects for CIBs.

36 MATERIALS SCIENCE↗

MoO x S y /Ni 3 S 2 Microspheres on Ni Foam as Highly Efficient, Durable Electrocatalysts for Hydrogen Evolution Reaction

Hydrogen energy derived from water splitting is the cleanest renewable energy source, but it is also very challenging to achieve because the hydrogen evolution reaction (HER) requires highly efficient and low-cost electrocatalysts. Here, we have fabricated a novel hierarchical system of amorphous molybdenum oxy/sulfide microspheres with crystalline Ni 3 S 2 intergrown in situ on Ni foam (MoO x S y /Ni 3 S 2 /NF) as an outstanding electrocatalyst for HER. The MoO x S y /Ni 3 S 2 /NF demonstrates an ultra-low overpotential of 58 mV at a current density of 10 mA cm -2 and extremely durable stability (>200 h), suggesting superior performance comparable to that of Pt-C/NF under acidic conditions. The X-ray absorption fine structure (XAFS) determines the average valence state of Mo to be +(5 + δ), with a coordination motif by O and S. To explain such high HER activity, a [Mo 2 O 2 (S,O) 4 ] dimer-based periodic model structure with the average composition of [Mo 4 O 8 S 4 ] interfaced with the Ni 3 S 2 (101) surface is proposed. The interactions between the Ni of Ni 3 S 2 and bridging S/O of [Mo 4 O 8 S 4 ] result in an average formal Mo charge state between +5 and +6, and significant charge transfer from Ni 3 S 2 to [Mo 4 O 8 S 4 ] activates the Mo = O bonds. The calculated |ΔG H* | of less than 50 meV suggests that the double-bonded O is the most active site. This work points to the importance of oxy/sulfides with Mon+ (+5 < n < +6) as exceptional electrochemical catalysts for HER.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanostructured Conductive Metal Organic Frameworks for Sustainable Low Charge Overpotentials in Li–Air Batteries

Lithium-oxygen batteries are among the most attractive alternatives for future electrified transportation. However, their practical application is hindered by many obstacles. Due to the insulating nature of Li 2 O 2 product and the slow kinetics of reactions, attaining sustainable low charge overpotentials at high rates becomes a challenge resulting in the battery's early failure and low round trip efficiency. Herein, outstanding characteristics are discovered of a conductive metal organic framework (c-MOF) that promotes the growth of nanocrystalline Li 2 O 2 with amorphous regions. This provides a platform for the continuous growth of Li 2 O 2 units away from framework, enabling a fast discharge at high current rates. Moreover, the Li 2 O 2 structure works in synergy with the redox mediator (RM). The conductivity of the amorphous regions of the Li 2 O 2 allows the RM to act directly on the Li 2 O 2 surface instead of catalyst edges and then transport through the electrolyte to the Li 2 O 2 surface. This direct charge transfer enables a small charge potential of <3.7 V under high current densities (1-2 A g -1 ) sustained for a long cycle life (100-300 cycles) for large capacities (1000-2000 mAh g -1 ). These results open a new direction for utilizing c-MOFs towards advanced energy storage systems.

25 ENERGY STORAGE↗

Layered Transition Metal Oxides as Ca Intercalation Cathodes: A Systematic First-Principles Evaluation

Finding high-voltage Ca cathode materials is a critical step to unleashing the full potential of high-energy-density Ca-ion batteries. Therefore, first-principles calculations are used to demonstrate that P-type layered calcium transition metal (TM) oxide materials (CaTM 2 O 4 ) with a range of TM substitutions (TM = Ti, V, Cr, Mn, Fe, Co, and Ni) have excellent battery-related properties including thermodynamic stability, average voltage, energy density, synthesizability, ionic mobility, and electronic structure. However, the thermodynamic stability of the charged phase and TM redox activity are shown to be sensitive to TM selection, with CaCo 2 O 4 having the best balance of all considered properties. The utility of combining multiple TMs to expand the chemical search space for TM substitutions is demonstrated by mixing Co and Ni in layered CaTM 2 O 4 .

25 ENERGY STORAGE↗

Increasing Ionic Conductivity of Poly(ethylene oxide) by Reaction with Metallic Li

Poly(ethylene oxide) (PEO) was the first lithium-ion conducting polymer developed 50 years ago and is still the most popular electrolyte matrix for solid-state lithium metal batteries. While many studies focus on increasing PEO ionic conductivity through doping with Li salts, little work has addressed using PEO and Li directly to generate Li + -conducting species in situ. Reaction between PEO and Li leads to ionic conductivity largely from Li + , in contrast to the case of added salts where the anion contribution dominates. Herein, electrochemical impedance spectroscopy shows the ionic conductivity of PEO thin films increases up to three orders of magnitude (from 10 –7 to 10 –4 S cm –1 ) when contacted with Li at elevated temperature. This is due to the reduction of ether bonds, which produces lithium alkoxides that are responsible for Li + transport. Density functional theory analysis confirms this mechanism as thermodynamically favorable. X-ray photoelectron spectroscopy also shows the presence of organolithium species and Li 2 O, which are responsible for propagating reactions with PEO and forming an electronically insulating layer at the PEO–Li interface that halts further reaction, respectively. The underlying mechanisms of Li–polymer electrolyte reactions is clarified and new pathways for in situ Li + doping of polymer electrolytes is presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗