Search NASA⌕ Search

Engineering topics

Zasadzinski, J

Publications and source records attributed to Zasadzinski, J.

New Homogeneous Standards by Atomic Layer Deposition for Synchrotron X-ray Fluorescence and Absorption Spectroscopies.

Quantification of synchrotron XRF analyses is typically done through comparisons with measurements on the NIST SRM 1832/1833 thin film standards. Unfortunately, these standards are inhomogeneous on small scales at the tens of percent level. We are synthesizing new homogeneous multilayer standards using the Atomic Layer Deposition technique and characterizing them using multiple analytical methods, including ellipsometry, Rutherford Back Scattering at Evans Analytical, Synchrotron X-ray Fluorescence (SXRF) at Advanced Photon Source (APS) Beamline 13-ID, Synchrotron X-ray Absorption Spectroscopy (XAS) at Advanced Light Source (ALS) Beamlines 11.0.2 and 5.3.2.1 and by electron microscopy techniques. Our motivation for developing much-needed cross-calibration of synchrotron techniques is borne from coordinated analyses of particles captured in the aerogel of the NASA Stardust Interstellar Dust Collector (SIDC). The Stardust Interstellar Dust Preliminary Examination (ISPE) team have characterized three sub-nanogram, {approx}1{micro}m-sized fragments considered as candidates to be the first contemporary interstellar dust ever collected, based on their chemistries and trajectories. The candidates were analyzed in small wedges of aerogel in which they were extracted from the larger collector, using high sensitivity, high spatial resolution >3 keV synchrotron x-ray fluorescence spectroscopy (SXRF) and <2 keV synchrotron x-ray transmission microscopy (STXM) during Stardust ISPE. The ISPE synchrotron techniques have complementary capabilities. Hard X-ray SXRF is sensitive to sub-fg mass of elements Z {ge} 20 (calcium) and has a spatial resolution as low as 90nm. X-ray Diffraction data were collected simultaneously with SXRF data. Soft X-ray STXM at ALS beamline 11.0.2 can detect fg-mass of most elements, including cosmochemically important oxygen, magnesium, aluminum and silicon, which are invisible to SXRF in this application. ALS beamline 11.0.2 has spatial resolution better than 25 nm. Limiting factors for Stardust STXM analyses were self-imposed limits of photon dose due to radiation damage concerns, and significant attenuation of <1500 eV X-rays by {approx}80{micro}m thick, {approx}25 mg/cm{sup 3} density silica aerogel capture medium. In practice, the ISPE team characterized the major, light elements using STXM (O, Mg, Al, Si) and the heavier minor and trace elements using SXRF. The two data sets overlapped only with minor Fe and Ni ({approx}1% mass abundance), providing few quantitative cross-checks. New improved standards for cross calibration are essential for consortium-based analyses of Stardust interstellar and cometary particles, IDPs. Indeed, they have far reaching application across the whole synchrotron-based analytical community. We have synthesized three ALD multilayers simultaneously on silicon nitride membranes and silicon and characterized them using RBS (on Si), XRF (on Si{sub 3}N{sub 4}) and STXM/XAS (holey Si{sub 3}N{sub 4}). The systems we have started to work with are Al-Zn-Fe and Y-Mg-Er. We have found these ALD multi-layers to be uniform at {micro}m- to nm scales, and have found excellent consistency between four analytical techniques so far. The ALD films can also be used as a standard for e-beam instruments, eg., TEM EELS or EDX. After some early issues with the consistency of coatings to the back-side of the membrane windows, we are confident to be able to show multi-analytical agreement to within 10%. As the precision improves, we can use the new standards to verify or improve the tabulated cross-sections.

43 PARTICLE ACCELERATORS↗

Evidence of surface paramagnetism in niobium and consequences for the superconducting cavity surface impedance.

The presence of magnetic impurities in native niobium oxides have been confirmed by Point contact spectroscopy (PCT), SQUID magnetometry and Electron paramagnetic resonance (EPR). All niobium (Nb) samples displayed a small impurity contribution to the magnetic susceptibility at low temperatures which exhibited Curie-Weiss behavior, indicative of weakly coupled localized paramagnetic moments. By examining Nb samples with widely varying surface-to-volume ratios (rods, foils, wires, powders) it was found that the impurity contribution is correlated with surface area. Tunneling measurements which use the native oxide layers as barriers exhibit a zero-bias conductance peak which splits in a magnetic field >; 4T, consistent with the Appelbaum-Anderson model for spin flip tunneling. Viewed together the experiments strongly suggest that the native oxides of Nb are intrinsically defective, and consistently exhibit localized paramagnetic moments caused by oxygen vacancies in Nb{sub 2}O{sub 5}. The computation of the surface impedance (R{sub s}) in presence of magnetic impurities in the Shiba approximation reveals the saturation at low temperature of R{sub s}, suggesting that magnetic impurities are responsible for the so-called residual resistance. These properties may have an impact on Nb based superconducting devices and shine a new light on the origin of the paramagnetic Meissner effect (PME).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tunneling study of SRF cavity-grade niobium.

Niobium, with its very high H{sub C1}, has been used in superconducting radio frequency (SRF) cavities for accelerator systems for 40 years with continual improvement. The quality factor of cavities (Q) is governed by the surface impedance R{sub BCS}, which depends on the quasiparticle gap, delta, and the superfluid density. Both of these parameters are seriously affected by surface imperfections (metallic phases, dissolved oxygen, magnetic impurities). Loss mechanism and surface treatments of Nb cavities found to improve the Q factor are still unsolved mysteries. We present here an overview of the capabilities of the point contact tunneling spectroscopy and Atomic layer deposition methods and how they can help understanding the High field Q-drop and the mild baking effect. Tunneling spectroscopy was performed on Nb pieces from the same processed material used to fabricate SRF cavities. Air exposed, electropolished Nb exhibited a surface superconducting gap Delta = 1.55 meV, characteristic of clean, bulk Nb, however the tunneling density of states (DOS) was broadened significantly. Nb pieces treated with the same mild baking used to improve the Q-slope in SRF cavities revealed a much sharper DOS. Good fits to the DOS are obtained using Shiba theory suggesting that magnetic scattering of quasiparticles is the origin of the degraded surface superconductivity and the Q-slope problem of Nb SRF cavities.

43 PARTICLE ACCELERATORS↗

Atomic Layer Deposition for SRF Cavities

We have begun using Atomic Layer Deposition (ALD) to synthesize a variety of surface coatings on coupons and cavities as part of an effort to produce rf structures with significantly better performance and yield than those obtained from bulk niobium, The ALD process offers the possibility of conformally coating complex cavity shapes with precise layered structures with tightly constrained morphology and chemical properties. Our program looks both at the metallurgy and superconducting properties of these coatings, and also their performance in working structures. Initial results include: 1) evidence from point contact tunneling showing magnetic oxides can be a significant limitation to high gradient operation, 2) experimental results showing the production sharp niobium/oxide interfaces from a high temperature bake of ALD coated Al2O3 on niobium surfaces, 3) results from ALD coated structures.

36 MATERIALS SCIENCE↗

Atomic Layer Deposition for SRF Cavities

We have begun using Atomic Layer Deposition (ALD) to synthesize a variety of surface coatings on coupons and cavities as part of an effort to produce rf structures with significantly better performance and yield than those obtained from bulk niobium, The ALD process offers the possibility of conformally coating complex cavity shapes with precise layered structures with tightly constrained morphology and chemical properties. Our program looks both at the metallurgy and superconducting properties of these coatings, and also their performance in working structures. Initial results include: (1) results from ALD coated cavities and coupons, (2) new evidence from point contact tunneling (PCT) showing magnetic oxides can be a significant limitation to high gradient operation, (3) a study of high pressure rinsing damage on niobium samples.

43 PARTICLE ACCELERATORS↗