Search NASA⌕ Search

Engineering topics

Zawodzinski, Thomas

Publications and source records attributed to Zawodzinski, Thomas.

Correlation Between Microscopic Current Fluctuations Observed at Ultra-Microelectrodes and Macroscopic Bulk Electrolysis Performance in Redox-Active Microemulsions

Microemulsions (μEs) have been proposed as redox flow battery (RFB) electrolytes that maximize ionic conductivity and charge capacity by synergizing two immiscible phases. However, charge transfer during electrolysis in μEs is poorly understood. Here, we show that ultramicroelectrode electrolysis of ferrocene-loaded μEs –20%, 60%, and 90% water - reveals stochastic current fluctuations. These are differentiated in the scanning electrochemical microscopy (SECM) geometry, where power spectral density analysis showed distinct changes in the frequency contributions. SECM in the substrate generation-tip collection mode showed that fluctuations arise under mass-transfer control. Significant differences in the diffusion coefficient of ferrocene species were deducted from SECM approach curves, suggesting phase transfer behavior. Using bulk electrolysis, we calculated the charge accessibility and cycling behavior in the μEs. A decrease in the stochastic behavior of the μEs seems to correlate to a higher accessibility and cycling performance, with the 90% water μE displaying the best reversibility and the 60% the lowest. Altogether, these results suggest that Marangoni-type convection driven by concentration gradients and/or μE restructuring during charge transfer play a role in the electrochemical performance of μEs. This presents opportunities for screening and diagnosing the performance of these emerging RFB electrolytes.

25 ENERGY STORAGE↗

Synthesis of Alkoxy-TEMPO Aminoxyl Radicals and Electrochemical Characterization in Acetonitrile for Energy Storage Applications

In this paper, we describe the synthesis and characterization of alkoxylated TEMPO, (2,2,6,6-tetramethylpiperidin-1-yl)oxyl, radicals with potential application in organic non-aqueous redox flow batteries. The behavior of a series of TEMPO derivatives with varying lengths of alkoxy chain is analyzed in acetonitrile solutions using electrochemistry techniques, electron paramagnetic resonance (EPR) spectroscopy, and measurements of permeability through three different membranes. Electrochemical redox potentials are only weakly dependent on the substituent, but, in contrast, exchange current densities derived from the data do depend on the substitution. EPR lends further insight into these properties via the determination of hyperfine splitting constant and rotational correlation time. There is a negligible effect of the substituents on those parameters among the modified TEMPO radicals. Finally, permeation rates of modified TEMPO derivatives through membranes depend significantly on both the membrane and the substitution of TEMPO, providing insights into capacity fade measurements in the literature.

25 ENERGY STORAGE↗

Microemulsions as Emerging Electrolytes: The Correlation of Structure to Electrochemical Response

We describe the structural studies of microemulsions (μEs) prepared from water, toluene, butanol, and polysorbate 20 (PS20) that we recently used as electrolytes. Small-angle neutron scattering was used to monitor the development of the bicontinuous system as a function of the water-to-surfactant mass ratio on a constant oil-to-surfactant dilution line, revealing how the domain size, correlation length, amphiphilicity factor, and bending moduli change with composition. Kratky and Porod analyses are also employed, providing further structural detail of the scattering domains. Here, we demonstrate that controlling the water-to-surfactant ratio with a constant oil-to-surfactant dilution affects the bicontinuous phase, reveals a sizeable compositional region with structural similarities, and provides insight into the correlation of structure to physical properties. Voltammetric results are presented to examine how the evolution of the bicontinuous structure formed in a μE prepared from water, toluene, butanol, and PS20 contributes to the electrochemical response. These findings, therefore, provide essential information that will guide the formulation of μEs as electrolytes for energy storage.

25 ENERGY STORAGE↗

Microemulsions: Breakthrough Electrolytes for Redox Flow Batteries

Aqueous and non-aqueous redox flow batteries (RFBs) have limited energy and current densities, respectively, due to the nature of the electrolytes. New approaches to electrolyte design are needed to improve the performance of RFBs. In this work, we combined a highly conductive aqueous phase and an organic redox-active phase in a microemulsion to formulate a novel RFB electrolyte. As a proof-of-concept, we demonstrate an RFB using this microemulsion electrolyte with maximum current density of 17.5 mA·cm −2 with a 0.19 M posolyte and 0.09 M negolyte at a flow rate of only ∼2.5 ml·min −1 , comparable to early vanadium electrolyte RFBs at similar flow rates on a per molar basis. The novel active negolyte component is an inexpensive oil-soluble vitamin (K 3 ). By combining aqueous and organic phases, the solvent potential window and energy density may be increased without sacrificing current density and new redox couples may be accessed. Microemulsion electrolytes show great promise for improved performance and increased energy densities in aqueous RFBs but the path forward is complex. We end with discussion of areas that need work to achieve the potential of these electrolytes.

25 ENERGY STORAGE↗

Evolution of microscopic heterogeneity and dynamics in choline chloride-based deep eutectic solvents

Deep eutectic solvents (DESs) are an emerging class of non-aqueous solvents that are potentially scalable, easy to prepare and functionalize for many applications ranging from biomass processing to energy storage technologies. Predictive understanding of the fundamental correlations between local structure and macroscopic properties is needed to exploit the large design space and tunability of DESs for specific applications. Here, we employ a range of computational and experimental techniques that span length-scales from molecular to macroscopic and timescales from picoseconds to seconds to study the evolution of structure and dynamics in model DESs, namely Glyceline and Ethaline, starting from the parent compounds. We show that systematic addition of choline chloride leads to microscopic heterogeneities that alter the primary structural relaxation in glycerol and ethylene glycol and result in new dynamic modes that are strongly correlated to the macroscopic properties of the DES formed.

36 MATERIALS SCIENCE↗

Decoupling Conductivity and Solubility in Electrolytes Using Microemulsions

Redox flow batteries have recently received considerable attention as possible large-scale energy storage devices, but their low energy density has inhibited widespread application. In this work, a novel strategy of decoupling conductivity and solubility of electrolytes using microemulsion is put forward to enhance ionic conduction of non-aqueous electrolytes, increase the selectivity of active species, improve the battery voltage, and eventually achieve the possibility of high energy density. We report a study of the electrochemistry of ferrocene in single phase Tween® 20/1-butanol/H 2 O/toluene microemulsion system at 20 °C. At low and intermediate surfactant to water weight ratios (<0.5/0.5), the voltammogram exhibits reversible electrochemical behavior, while at high surfactant levels the curves show lower levels of reversibility. The latter voltammograms have a form typically associated with high resistance in solution, consistent with a gradual transition in microstructure as surfactant levels increase. This change in structure is supported by correlations with conductivity results based on the literature. The voltammograms show little evidence of anomalies in double layer capacitance or electrode "blocking" by droplets, suggesting that the electron transfer is indeed occurring in a facile manner between the electrode and the ferrocene inside the oil phase.

25 ENERGY STORAGE↗

A Study of Ferrocene Diffusion in Toluene/Tween 20/1-Butanol/Water Microemulsions for Redox Flow Battery Applications

Redox flow batteries (RFBs) possess multiple advantages as a flexible energy storage solution. However, RFB researchers are still facing many challenges in finding an appropriate electrolyte. Microemulsions have recently been proposed as a promising alternative RFB electrolyte because of their ability to accommodate organic redox species with fast electron transfer rates that are not soluble in aqueous phase, while still offering the high conductivity of an aqueous salt electrolyte. In this work, we focused on understanding the transport of ferrocene (Fc) in a toluene/Tween 20/1-butanol/water model microemulsion and studied the compositional influence on Fc diffusion. The results show that Fc redistributes among the oil, surfactant, and water microenvironments, and the corresponding diffusion and partition coefficients are quantified. Thus, a tortuous path diffusion model is proposed to describe the mass transport of Fc to an electrode surface. Diffusion coefficients are also obtained by pulsed-field gradient nuclear magnetic resonance (PFG NMR), while the values for Fc diffusion are substantially higher than those from electrochemical measurements, suggesting that they measure samples in different ways. The current contributions from each microenvironment indicate that the Fc permeability is much higher in the oil, even though the electron transfer reaction is likely occurring in the surfactant.

25 ENERGY STORAGE↗

Electron Transfer in Microemulsion-Based Electrolytes

The use of flowing electrochemical reactors, for example, in redox flow batteries and in various electrosynthesis processes, is increasing. This technology has the potential to be of central significance in the increased deployment of renewable electricity for carbon-neutral processes. A key element of optimizing efficiency of electrochemical reactors is the combination of high solution conductivity and reagent solubility. In this work, we show a substantial rate of charge transfer for an electrochemical reaction occurring in a microemulsion containing electroactive material is loaded inside the nonpolar (toluene) subphase of the microemulsion. The measured rate constant translates to an exchange current density comparable to that in redox flow batteries. The rate could be controlled by the surfactant, which maintains partitioning of reactants and products by forming an interfacial region with ions in the aqueous phase in close proximity. The hypothesized echanism is evocative of membrane-bound enzymatic reactions. Achieving sufficient rates of electrochemical reaction is the product of an effort designed to establish a reaction condition that meets the requirements of electrochemical reactors using microemulsions to realize a separation of conducting and reactive elements of the solution, opening a door to the broad use of microemulsions to effect controlled electrochemical reactions as steps in more complex processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemically Cross-Linked Cellulose Nanocrystal Aerogels for Effective Removal of Cation Dye

In this study, porous aerogels were prepared by directional freeze-drying via cross-linking cellulose nanocrystals (CNCs) with poly(methyl vinyl ether-co-maleic acid) (PMVEMA) and poly(ethylene glycol) (PEG). The thermal properties and physical adsorption performance toward cation methylene blue dye of the obtained CNC aerogels were investigated. The maximum degradation temperature was increased from 324&#x000B0;C of CNCs to 355&#x000B0;C of cross-linked CNC aerogels. The dye adsorption isotherm results showed that the maximum methylene blue adsorption capacity of CNC aerogels was 116.2 mg g &#x02212;1 , according to the Langmuir model, which was mainly due to the electrostatic attractions between negatively charged carboxyl groups or sulfonate groups on the CNC aerogles and cation MB molecules. The reusability test showed that the CNC aerogels contained the same dye adsorption performance in five adsorption/desorption cycles. Overall, this study described an ideal alternative for water purification with high dye adsorption capacity and enhanced physical performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanostructured carbon electrocatalyst supports for intermediate-temperature fuel cells: Single-walled versus multi-walled structures

It is unknown if nanostructured carbons possess the requisite electrochemical stability to be used as catalyst supports in the cathode of intermediate-temperature solid acid fuel cells (SAFCs) based on the CsH2PO4 electrolyte. To investigate this application, single-walled carbon nanohorns (SWNHs) and multi-walled carbon nanotubes (MWNTs) were used as supports for Pt catalysts in SAFCs operating at 250 °C. SWNH-based cathodes display greater maximum activity than their MWNT-based counterparts at a cell voltage of 0.8 V, but are unstable in the SAFC cathode as a consequence of electrochemical carbon corrosion. MWNT-based cells are resistant to this effect and capable of operation for at least 160 h at 0.6 V and 250 °C. Cells fabricated with nanostructured carbon supports are more active (52 mA cm -1 vs. 28 mA cm -1 at 0.8 V) than state-of-the-art carbon-free formulations while simultaneously displaying enhanced Pt utilization (40 mA mgPt -1 vs. 16 mA mgPt -1 at 0.8 V). Finally, these results suggest that MWNTs are a viable support material for developing stable, high-performance, low-cost air electrodes for solid-state electrochemical devices operating above 230 °C.

25 ENERGY STORAGE↗

Nanostructure-Driven Ion Transport in PCBM-Based Polymer Electrolytes

Nanostructure-Driven Ion Transport in PCBM-Based Polymer ElectrolytesChe-Nan Sun1, Thomas A. Zawodzinski1,2, Fei Ren3, Jong Kahk Keum1 and Jihua Chen1, (1)Oak Ridge National Laboratory, (2)The University of Tennessee, (3)Temple University Polyethylene oxide or PEO is an extensively-examined candidate for solid polymer electrolyte materials of lithium ion batteries, and its composite electrolytes has promising ion conductivities.[1-3] Oxide nanoparticles with sizes of 5-10 nm are often introduced into these polymer-based composite electrolytes in order to suppress their room-temperature crystallite formation.1-9 The size, geometry and surface functionality of the added particles were known to largely affect the structure and performance of the blended electrolytes.5,10 In this study, we examined a functionalized-fullerene-based composite electrolytes, providing details in their self-assembled nanostructures, modulus, hardness, as well as temperature-dependent ion-conducting behaviors. To the best of our knowledge, no fullerene-based, lithium conducting, composite electrolyte has been reported previously. Herein we used a bench-mark fullerene derivative, phenyl-C61-butyric acid methyl ester (PCBM) as a model fullerene compound and performed impedance spectroscopy, equivalent circuit modeling, nanoscale elemental mapping (in transmission electron microscope), wide-angle X-ray diffraction, as well as nanoindentation to shed light on a 6-fold enhancement in low temperature (less than 50oC) ion conductivity of PEO - lithium bis(trifluoromethanesulfonyl) imide (LiTFSI)-PCBM electrolytes, along with the underlying changes in nanomorphology , mechanical properties, and crystal structures. Based on a previous density functional theory (DFT) calculation, 11 the interaction energies Ei among PEO polymers is estimated to be 2.58 kcal mol-1 per monomer, the Ei between PCBM and PEO is 3.50 kcal mol-1 per monomer (PCBM is taken as 1 repeat unit), and the Ei among PCBMs themselves is 6.01 kcal mol-1 per monomer. This explains that at very low PCBM weight percentage, without sufficient PCBM-PCBM contacts, it is more energetically favorable for fullerenes to disperse into PEO matrix. However, with higher PCBM concentration, the fullerenes will efficiently pack with each other into domains with gradually increased dimensions. Quantification of PCBM domains is performed by line scan analysis of energy filtered TEM (EFTEM) images. Upon the addition of PCBM, the average domain sizes gradually increase from 3.4±1 nm ( 0% PCBM), to 4.6±1 nm (10% PCBM) and 4.9±2 nm (20% PCBM), and finally to 7.5±5 nm (40% PCBM ). (A precise determination of PCBM domain dimension is not possible when the domain size is less than 3 nm, due to the lack of EFTEM contrast in these samples). We attribute the observed ion conductivity improvement to those nanomorphological variation in PCBM-PEO-LiTFSi systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of ionomer content on the structure and performance of PEFC membrane electrode assemblies

Nafion ionomer content of the cathode catalyst-layer of a polymer electrolyte fuel cell (PEFC), made by the decal hot pressing method, has been investigated for its effect on performance and structure of the membrane electrode assembly (MEA). Varying Nafion content was shown to have an effect on performance within the entire range of polarization curves (i.e. kinetic, ohmic, and mass-transport regions) as well as on the structure. AFM analysis shows the effect of Nafion on the dispersion of carbon aggregates. Further analysis using TEM demonstrates the effect of Nafion on both the dispersion of carbon aggregates and the distribution and thickness of the Nafion ionomer films surrounding the catalyst/carbon aggregates. The MEA structure change correlates well with the MEA performance on both kinetics and mass-transport region. The determining factors on the performance of MEA are the interfacial zone (between the ionomer and catalyst particle), the dispersion of catalyst/carbon aggregates and the distribution/thickness of Nafion films. An optimized Nafion content in the range of 27 6 wt.% for the cathode was determined for an E-TEK 20% Pt3Cr/C catalyst at a loading of 0.20mg Pt/cm2.

30 DIRECT ENERGY CONVERSION↗