Engineering topics

Zenyuk, Iryna V

Publications and source records attributed to Zenyuk, Iryna V.

4 records

DOE OSTI2026

Mitigation of hydrogen crossover in liquid alkaline water electrolysers using gas recombination catalysts

The rising demand for hydrogen calls for improvements in the efficiency of liquid alkaline water electrolysers (LAWEs), which can be fulfilled by advanced electrodes or separators. Nevertheless, they also intensify hydrogen crossover and safety concerns, thus mandating efficient mitigation strategies. Here we studied the correlation between cathodes and hydrogen crossover behaviours and mitigated safety risks by designing a gas recombination catalyst (GRC). We attribute the elevated hydrogen crossover associated with platinum-based cathodes to their preferential utilization for the hydrogen evolution reaction that creates elevated hydrogen supersaturation, as evidenced by direct measurements of dissolved hydrogen concentration. Varying the placement of platinum layers relative to the cathode–separator interface also supports this conclusion. The implementation of a GRC reduces hydrogen crossover by 95% without affecting LAWE performance and functions for over 1,000 h at 1 A cm−2. This study provides insights into hydrogen supersaturation and the crossover mechanism, as well as offering a promising pathway to enhance the efficiency and reliability of alkaline water electrolysis.

Liu, Haotian↗

DOE OSTI2025

Physical model and experimental validation of a high temperature proton exchange membrane electrochemical hydrogen pump cell for efficient single-stage extraction of low concentration hydrogen gas

There is interest in valorization of existing natural gas infrastructure to facilitate the co-transportation of hydrogen via blending of hydrogen gas initially at limited concentrations of 1–20 vol% H2 and to subsequently extract hydrogen at fuel cell quality standards (SAE J2719/ISO14687-2). High temperature proton exchange membrane electrochemical hydrogen pump (HT-PEM EHP) based on phosphoric acid doped polybenzimidazole (PA-PBI) exhibits good performance at elevated temperatures (>120 °C), which provides desirable tolerance to non-methane natural gas constituents that are problematic for lower temperature based EHP. To better understand the suitability of the HT-PEM EHP for such gas separation processes, a two-dimensional model of EHP based on PA-PBI was developed. The model is validated for several relevant operating conditions and across cells with differing amounts of phosphoric acid content in the electrodes. Operando micro x-ray computed tomography (CT) imaging of an HT-PEM EHP was used to further validate physical parameters and assumptions of the model. The impacts of pressure, relative humidity of the anode feed, and concentration of feed gases on separation performance are investigated. This study shows that a specific energy of separation of 5.1 kWh/kg H2 at a hydrogen recovery factor (HRF) of 50 vol% can be achieved in a single stage with the EHP, producing fuel cell quality hydrogen purity of 99.99 vol% H2 from a 2 vol% H2/CH4 feed blend, while pressurizing the product H2 at a pressure ratio of 1.3 relative to feed pressure.

Stansberry, John M↗

DOE OSTI2025

Enhancing water and oxygen transport through electrode engineering for AEM water electrolyzers

Anion-exchange membrane water electrolyzers (AEMWEs) can accelerate the deployment of more efficient and affordable hydrogen production solutions. Here, electrode structure is shown to affect water back-diffusion and oxygen transport, which, in return, governs overpotential behaviors in AEMWEs. Measurements indicate that electrode with copious catalytic sites produces water close to the AEM, creating a higher water gradient and driving water back-diffusion, which improves membrane hydration and mass transport. In situ measurement reveals a high pH gradient near the anode surface, which affects anode kinetics. Operando measurement shows reduced oxygen accumulation when decoupling oxygen production and transport on anode. Catalyst ink rheology and stability are tuned with additives to realize scalable fabrication of electrodes with enhanced transport features, allowing AEMWE to operate at 2 A cm−2 for over 1,000+ h at a 2.3 μV h−1 degradation rate. Analysis during and post-durability provides insights into degradation mechanisms. This work demonstrates an electrode design strategy for efficient and durable AEMWEs.

AEM↗

DOE OSTI2020

Modeling Single and Two-Phase Transport in Thin Porous Layers Using a Composite Continuum-Pore Network Formulation

In this work, a composite continuum-pore network formulation is presented to model single and two-phase transport thin porous layers, such as gas diffusion layers in polymer electrolyte fuel cells (PEFCs) and active electrodes in redox flow batteries (RFBs). The formulation can be integrated into CFD codes, thus combining the ease of implementation of continuum-based modeling and the computational power of pore-network modeling. The composite model includes a control volume (CV) mesh at the layer scale, which embeds a cubic pore network [1,2]. The pore-network model is used to determine analytically local anisotropic effective transport properties (local effective diffusivity and permeability), which are mapped onto the CV mesh to simulate transport in the porous transport layer [3,4]. Good agreement is found between the predicted global effective transport properties (global effective diffusivity and permeability) under dry and wet conditions and previous experimental data reported in the literature for Toray TGP-H series carbon paper. Water saturation distributions are also compared with results obtained using X-ray computed tomography [4]. [1] P.A. García-Salaberri, I.V. Zenyuk, J.T. Gostick, A.Z. Weber, Modeling Gas Diffusion Layer in Polymer Electrolyte Fuel Cells Using a Continuum-Based Pore-Network Formulation, ECS Trans. 97 (2020) 615. [2] P.A. García-Salaberri, Modeling diffusion and convection in thin porous transport layers using a composite continuum-network model: Application to gas diffusion layers in polymer electrolyte fuel cells, Int J. Heat Mass Transf. (2020), submitted. [3] P.A. García-Salaberri, J.T. Gostick, G. Hwang, A.Z. Weber, M. Vera, Effective diffusivity in partially-saturated carbon-fiber gas diffusion layers: Effect of local saturation and application to macroscopic continuum models, J. Power Sources 296 (2015) 440–453. [4] P.A. García-Salaberri, G. Hwang, M. Vera, A.Z. Weber, J.T. Gostick, Effective diffusivity in partially-saturated carbon-fiber gas diffusion layers: Effect of through-plane saturation distribution, Int. J. Heat Mass Transf. 86 (2015) 319–333.

Garcia-Salaberri, Pablo↗