Local and Bulk Probe of Vanadium-Substituted α-Manganese Oxide (α-KxVyMn8-yO16) Lithium Electrochemistry
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Zhang, Bingjie.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Samples of Mg-todorokite with mixed nanosheet & nanowire (referred to as nanosheets for the sake of simplicity) and pure nanowire morphology were prepared to probe the morphological impact on battery relevant electrochemistry. The samples had similar physicochemical properties where the Mg-todorokite nanosheets had a composition of Mg 0.20 MnO 2 with a crystallite size of 9 nm and water content of 0.29 moles of H 2 O per formula unit, while the nanowires had a composition of Mg 0.19 MnO 2 with a crystallite size of 14 nm and water content of 0.28. The electrochemistry of the Mg-todorokite materials was evaluated using cyclic voltammetry, galvanostatic cycling, and rate capability testing. The Mg-todorokite nanosheets showed higher discharge capacity than the nanowires in lithium, sodium and magnesium-based electrolytes. Notably, the nanowire materials exhibited excellent cycling stability compared to the nanosheets in lithium and sodium-based batteries. Finally, x-ray absorption spectroscopy (XAS) of lithiated samples suggests that Mn in the nanosheet containing material was more highly reduced to Mn 3+ after the 1st full discharge explaining the higher initial capacities observed. However, a MnO-like structural distortion was observed after extended cycling in the nanosheet material consistent with its poorer capacity retention.
Rational design of energy storage materials requires mechanistic understanding which relies on atomic scale characterization of structure and defects. In this paper we utilize vanadium (V)-substituted one-dimensional cryptomelane as a model material to study structural features critical to electrochemical reversibility of the cathode in lithium-ion batteries. We found the substitution of manganese (Mn) atoms in the tunnel wall with V enhances structural uniformity in the parent KMn 8 O 16 material by inhibiting formation of irregular (2 × 3 and 2 × 1) manganese oxide tunnel structures. Upon lithiation, both transmission electron microscopy (TEM) and density functional theory (DFT) reveal significant structural evolution, eventually resulting in phase separation and formation of highly reduced manganese oxide. During this process, Mn 4+ accepts electrons donated by intercalated Li, while the V 4+ substituent is not electrochemically reduced but acts to stabilize the tunnel framework structure. As a result, the V substituted material shows higher operating voltage and improved electrochemical reversibility. Our results highlight the benefits of V-substitution in cryptomelane, and the significance of integrating characterization with simulation for understanding and developing design principles for lithium ion battery materials.
Not Available
Solid state batteries are an emerging alternative to traditional liquid electrolyte cells that provide potential for safe and high-energy density power sources. This report describes a self-forming, solid state battery based on the Li/I 2 couple using an LiI-rich LiI(3-hydroxypropionitrile) 2 electrolyte (LiI–LiI(HPN) 2 ). As the negative and positive active materials are generated in situ, the solid electrolyte–current collector interfaces play a critical role in determining the electrochemical response of the battery. Furthermore, we report the investigation of solid electrolyte–current collector interfaces with a self-forming LiI–LiI(HPN) 2 solid electrolyte and the role of varying interface design in reducing resistance during cycling.
Sodium containing 2 × 4 (0.46nm × 0.92nm) tunnel structured manganese dioxide (Na-2 × 4-MnO 2 ) nanofibers are hydrothermally synthesized here. The nanofibrous Na-2 × 4-MnO 2 was thoroughly characterized using X-ray diffraction (XRD), thermogravimetric analysis (TGA), inductively coupled plasma optical emission spectroscopy (ICP-OES), N2 sorption, and electron microscopy (SEM and TEM) and is assigned a formula of Na 0.25 MnO 2 .0.16H 2 O. The electrochemistry of Na-2 × 4-MnO 2 in non-aqueous Li, Na and Mg batteries is compared for the first time and first cycle delivered capacities were found to be 152mAh/g, 86mAh/g, and 307mAh/g, respectively. Characterization of the active material after electrochemical tests demonstrated that Na-2 × 4-MnO 2 preserved both its crystallographic structure and nanofibrous morphology after cycling in Na and Li cells, however, Na-2 × 4-MnO 2 lost its crystalline structure after cycling in a Mg based system.
Polytypism, or stacking disorder, in crystals is an important structural aspect that can impact materials properties and hinder our understanding of the materials. One example of a polytypic system is todorokite–MnO 2 , which has a unique structure among the transition-metal oxides, with large ionic conductive channels formed by the metal oxide framework that can be utilized for potential functionalization, from molecular/ion sieving to charge storage. In contrast to the perceived 3 × 3 tunneled structure, we reveal a coexistence of a diverse array of tunnel sizes in well-crystallized, chemically homogeneous one-dimensional todorokite–MnO 2 . We explain the formation and persistence of this distribution of tunnel sizes thermochemically, demonstrating the stabilization of a range of coherent large-tunnel environments by the intercalation of partially solvated Mg 2+ cations. In conclusion, based on structural behavior of the system, compared to the common well-ordered alkali-stabilized polymorphs of MnO 2 , we suggest generalizable principles determining the selectivity of structure selection by dopant incorporation.
In this paper, silver hollandite (Ag 1.4 Mn 8 O 16 ) has been synthesized by an aqueous, low-temperature co-precipitation technique to afford silver hollandite with distinct crystallite sizes (10 and 15 nm, identified as S-Ag 1.4 Mn 8 O 16 and L-Ag 1.4 Mn 8 O 16 , respectively) and equivalent silver content (x), allowing for the deconvolution of electrochemical effects related to crystallite size and silver content. The as-prepared silver hollandite materials were confirmed to be structurally analogous. Notably, TEM imaging reveals a high degree of bundling of S-Ag 1.4 Mn 8 O 16 nanorods compared to L-Ag 1.4 Mn 8 O 16 which facilitates more intimate connection of the S-Ag 1.4 Mn 8 O 16 material with enhanced interparticle contact. The electrochemical behavior and lithium diffusion properties were investigated by galvanostatic cycling, CV, electrochemical impedance, pulsed-discharge experiments, and ex-situ XAS analysis of cycled cathodes. Lithium based electrochemical cells containing S-Ag 1.4 Mn 8 O 16 delivered a capacity 15X higher than L-Ag 1.4 Mn 8 O 16 on cycle 1. Ex-situ XAS demonstrated structural change for S-Ag 1.4 Mn 8 O 16 and formation of Ag 0 on insertion of 3.8 Li + intercalation. However, the samples of L-Ag 1.4 Mn 8 O 16 were lithiated by a more limited 0.25 molar equivalents, where no significant structural changes were observed. Finally, the findings affirm crystallite size significantly impacts electrochemistry independent of cation occupancy of the α-MnO 2 type structure.
Battery electrodes are complex mesoscale systems comprised of an active material, conductive agent, current collector, and polymeric binder. Previous work showed that introduction of poly [3-(potassium-4-butanoate) thiophene] (PPBT) as a binder component coupled with a polyethylene glycol (PEG) surface coating on magnetite (Fe 3 O 4 ) nanoparticles enhanced electron and ion transport in the high capacity anode system. Here, the impact of Fe 3 O 4 crystallite size (10 nm vs. 20 nm) and surface chemistry were explored to evaluate their effects on interfacial interactions within the composite PEG/PPBT based electrodes and resultant battery performance. The Fe 3 O 4 synthesis methods inevitably lead to differences in surface chemistry. For instance, the Fe 3 O 4 particles synthesized using ammonium hydroxide appeared more dispersed, and afforded improved rate capability performance. Notably, chemical interactions between the active nanoparticles and PPBT binder were only seen with particles synthesized using triethylamine. Capacity retention and cycling performance were unaffected. Thus, this study provides fundamental insights into the significant impact of active material synthesis on the design and fabrication of composite battery electrodes.
Cryptomelane type manganese dioxides (α-MnO 2 , OMS-2) are interesting potential cathode materials due to the ability of their one dimensional (1D) tunnels to reversibly host various cations including Li + and an accessible stable 3+/4+ redox couple. Here, we synthesized metal cation free OMS-2 materials where the tunnels were occupied by only water and hydronium ions. Water was subsequently removed from the tunnels. Cation free OMS-2 and Dry-OMS-2 were used as cathodes in Li based batteries to investigate the role of tunnel water on their electrochemistry. The initial discharge capacity was higher for Dry-OMS-2 (252 mAh/g) compared to OMS-2 (194 mAh/g), however, after 100 cycles Dry-OMS-2 and OMS-2 delivered 137 mAh/g and 134 mAh/g, respectively. Li + ion diffusion was more facile for Dry-OMS as evidenced by rate capability, at 400 mA/g. Dry-OMS-2 delivered 135mAh/g whereas OMS-2 delivered ~115 mAh/g. This first report of the impact of tunnel water on the electrochemistry of OMS-2 type materials demonstrates that the presence of tunnel water in OMS-2 type materials negatively impacts the electrochemistry.
Efficient conduction of both electrons and cations (e.g., Li + ) has a profound effect on the current and capacity of lithium-based batteries. With this study, we focus on cathode effects, with the preparation of pure silver hollandite materials with variable silver ion content within (intra-tunnel) and on the surface of α-MnO 2 tunneled materials, followed by the measurement and analysis of impedance and electrochemistry data. Specifically, pure Ag x Mn 8 O 16-y materials with low (x = 1.13) and high (x = 1.54) intra-tunnel silver content are compared with Ag x Mn 8 O 16-y ·aAg 2 O (a = 0.25, 0.63, 1.43) composites prepared via a new Ag 2 O coating strategy. When the Ag 2 O (a = 0, 0.25) content is low, the material with higher intra-tunnel silver (x = 1.53) content delivers up to ~5-fold higher capacity accounted for by a ~10-fold lower impedance than its lower intra-tunnel silver (x = 1.13) counterpart. In the presence of high Ag 2 O content (a = 0.63, 1.43), both composites exhibit comparable impedance but the lower intra-tunnel silver (x = 1.13) composite delivers up to ~1.5-fold higher capacity than higher intra-tunnel silver composite, highlighting the key role of Li + transport under those conditions. Our results demonstrate material design strategies which can significantly increase electronic and ionic conductivities.