Engineering topics

Zhang, Chunyang

Publications and source records attributed to Zhang, Chunyang.

6 records

DOE OSTI2024

Work Function Tuning of a Weak Adhesion Homojunction for Stable Perovskite Solar Cells

Perovskite solar cells (PSCs) have demonstrated a comparable efficiency to Si-based cells. However, the buried interface with weak adhesion remains a critical issue since the ion migration enhanced by the built-in electric field at this interface might lead to instability. We report here that adjusting the energy-level alignment at the weak adhesion homojunction interface can mitigate ion migration and thereby enhance the stability and photovoltaic performance of PSCs. Functional molecules with self-assembled monolayer characteristics were introduced to the surface of the SnO2 layer using silane derivatives, which tuned the work function of the homojunction depending on the functional groups in the molecules and thereby significantly reduced the built-in electric field. The PSC exhibited a power conversion efficiency (PCE) of 25.3%. The maximum power point (MPP) tracking under continuous illumination confirmed that the device retained more than 97% of its initial PCE, even after 1,000 h.

homojunction↗

DOE OSTI2022

A Nearly Zero-Strain Li-Rich Rock-Salt Oxide with Multielectron Redox Reactions as a Cathode for Li-Ion Batteries

Li-rich oxide cathodes are drawing increasing attention as next-generation cathode materials for the development of high-energy-density Li-ion batteries due to their strikingly high capacities. However, transition-metal migration, irreversible structural phase transformations, and the irreversible release of oxygen are responsible for rapid capacity and voltage decay. This study reports a Li-rich cation-ordered rock-salt oxide Li x V 0.4 Ti 0.4 O 2 (LVTO, x = 0.97/1.2) with space group Fd$\bar{3}$m that delivers a high capacity of over 250 mAh g -1 and capacity retention up to 89% after 50 cycles. A comprehensive experimental analysis confirms that the capacity can be attributed to the reversible V 3+ /V 5+ multielectron cationic redox reactions and a minor contribution from reversible anionic redox reactions. Importantly, LVTO exhibits nearly zero-strain behavior upon (dis)charge cycling cycles, which is associated with reversible V migration from octahedral to tetrahedral sites. Here our results demonstrate that Li-rich rock-salt oxide LVTO could be a promising cobalt-free cathode material for Li-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA‐Free, Phase‐Pure, and Stable α‐Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

Abstract α‐Formamidinium lead iodide (α‐FAPbI 3 ) is one of the most promising candidate materials for high‐efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of α‐FAPbI 3 where both the composition and the phase are pure is very challenging. Herein, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)‐free and phase‐pure stable α‐FAPbI 3 films. The incorporation of volatile FA‐based additives in the precursor solutions completely suppresses the formation of non‐perovskite δ‐FAPbI 3 during film crystallization. Grains of the desired α‐phase are anchored together and stabilized when 4‐ tert ‐butylbenzylammonium iodide is permeated into the α‐FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21 % for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ≈90 % of their initial efficiency after storage at 50 °C for over 1600 hours.

Ling, Xufeng↗

DOE OSTI2021

Combined Precursor Engineering and Grain Anchoring Leading to MA-Free, Phase-Pure, and Stable α-Formamidinium Lead Iodide Perovskites for Efficient Solar Cells

a-Formamidinium lead iodide (a-FAPbI 3 ) is one of the most promising candidate materials for high-efficiency and thermally stable perovskite solar cells (PSCs) owing to its outstanding optoelectrical properties and high thermal stability. However, achieving a stable form of a-FAPbI 3 where both the composition and the phase are pure is very challenging. In this work, we report on a combined strategy of precursor engineering and grain anchoring to successfully prepare methylammonium (MA)-free and phase-pure stable a-FAPbI 3 films. The incorporation of volatile FA-based additives in the precursor solutions completely suppresses the formation of non-perovskite d-FAPbI 3 during film crystallization. Grains of the desired a-phase are anchored together and stabilized when 4-tert-butylbenzylammonium iodide is permeated into the a-FAPbI 3 film interior via grain boundaries. This cooperative scheme leads to a significantly increased efficiency close to 21% for FAPbI 3 perovskite solar cells. Moreover, the stabilized PSCs exhibit improved thermal stability and maintained ~90 % of their initial efficiency after storage at 50 degrees C for over 1600 hours.

14 SOLAR ENERGY↗

DOE OSTI2020

Fluorination effect for stabilizing cationic and anionic redox activities in cation-disordered cathode materials

We see that cation-disordered Li-excess cathodes with oxygen redox reactions are promising candidates for high-energy-density Li ion batteries. Nevertheless, the oxygen redox process that is required for the high capacity often comes with the oxygen loss, which leads to severe capacity degradation and voltage decay. In this work, we have successfully synthesized a series of Li-excess cation-disordered cathodes (Li 1.2 Mn 0.4+x Ti 0.4-x O 2-x Fx) (0 ≤ x ≤ 0.2) with different fluorine (F) contents. The electrochemical performance results show that the Li 1.2 Mn 0.55 Ti 0.25 O 1.85 F 0.15 (LMTOF0.15) exhibits the highest reversible capacity (275 mAh g -1 , under 30 mA g -1 ), cyclability, and voltage retentions. The mapping of resonant inelastic X-ray scattering (mRIXS) and differential electrochemical mass spectroscopy (DEMS) results reveal that the fluorination enhances the reversible lattice oxygen redox reaction while suppressing irreversible gas release and surface reactions. The X-ray Absorption Spectroscopy (XAS) during the initial two cycles shows that F-substitution alleviates the reduction of the Mn valence state during the whole (dis)charge processes in the bulk and at the surface of the material, results in higher average discharge voltage. In addition, the introduction of F improves the structural stability and suppresses local lattice distortion of the material. Therefore, LMTOF 0.15 is able to cycle with smaller polarization, less interfacial side reaction and Mn dissolution, and therefore results in enhanced cyclability. This work provides a comprehensive understanding of the fluorination effect on the cationic and anionic redox activities in cation-disordered Li-excess cathodes.

25 ENERGY STORAGE↗

DOE OSTI2020

Guanidinium-Assisted Surface Matrix Engineering for Highly Efficient Perovskite Quantum Dot Photovoltaics

Metal halide perovskite quantum dots (Pe-QDs) are of great interest in new-generation photovoltaics (PVs). However, it remains challenging in the construction of conductive and intact Pe-QD films to maximize their functionality. Herein, a ligand-assisted surface matrix strategy to engineer the surface and packing states of Pe-QD solids is demonstrated by a mild thermal annealing treatment after ligand exchange processing (referred to as “LE-TA”) triggered by guanidinium thiocyanate. The “LE-TA” method induces the formation of surface matrix on CsPbI 3 QDs, which is dominated by the cationic guanidinium (GA+) rather than the SCN-, maintaining the intact cubic structure and facilitating interparticle electrical interaction of QD solids. Consequently, the GA-matrix-confined CsPbI 3 QDs exhibit remarkably enhanced charge mobility and carrier diffusion length compared to control ones, leading to a champion power conversion efficiency of 15.21% when assembled in PVs, which is one of the highest among all Pe-QD solar cells. Additionally, the “LE-TA” method shows similar effects when applied to other Pe-QD PV systems like CsPbBr 3 and FAPbI 3 (FA = formamidinium), indicating its versatility in regulating the surfaces of various Pe-QDs. This work may afford new guidelines to construct electrically conductive and structurally intact Pe-QD solids for efficient optoelectronic devices.

36 MATERIALS SCIENCE↗