Search NASA⌕ Search

Engineering topics

Zhang, Hongbin

Publications and source records attributed to Zhang, Hongbin.

At least 91 records · Page 5

AN INVESTIGATION OF CONSISTENT UNCERTAINTY PROPAGATION AND SENSITIVITY ANALYSIS IN A MULTIPHYSICS ENVIRONMENT

The framework for a LOCA toolkit for the U.S. light water reactors (LOTUS) is outlined. LOTUS allows for the coupling of the core design code VERA-CS with the fuel performance code FRAPCON such that uncertainties can be propagated consistently. An analysis of inherent model discrepancies, confirms that all differences are either negligible or the focus on immediate future work. Monte Carlo sampling is performed on 15 inputs for a depletion case of one fuel assembly. Both uncertainty quantification (UQ) and sensitivity analysis (SA) are performed on the figures of merit (FOM) of minimum departure from nucleate boiling ratio (MDNBR), maximum fuel centerline temperature (MFCT), and gap conductance at peak power (GCPP). Pearson correlation coefficient, Sobol sensitivity indices, and the density-based, delta moment independent measure are used as SA metrics. All measures yield consistent rankings of inputs matching past work.

10CFR50.46c↗

A Revisit to the Hicks' Hyperbolic Two-pressure Two-phase Flow Model

Hicks’ two-phase flow model represents one of the earliest hyperbolic two-pressure two-phase flow models developed in the early 1980s. This model was developed under the separated flow condition, but could be potentially generalized for more realistic flow conditions that are of interest to reactor safety analysis (e.g., bubbly flow). This model is mathematically hyperbolic and therefore well- posed, as eigenvalues from the characteristic analysis found to be all real. Many currently popular two-pressure models are formulated similarly to Hicks’ two-pressure model, with the inclusion of a void fraction transport equation. The void fraction transport equation is closed using the knowledge of transverse velocity on the two-phase interface, which is assumed to be the solution of a Riemann problem in the transverse direction. Numerical experiments on two phenomenological test problems, i.e., the two-phase water faucet problem and the sedimentation problem, were performed using the Hicks’ model, as well as the single-pressure two-phase flow model. Numerical results demonstrate that the channel size, which appears in the void fraction transport equation, has significant impact on the behavior of the Hicks’ model. By comparing to single-pressure model results and available analytical solutions, it was found that Hicks’ model with very small channel width behaves similarly to the single-pressure model. On the contrary, Hicks’ model with large channel width, however, constantly leads to unphysical liquid-phase pressure. These numerical experiments indicate that using the Riemann problem to close the equation system in Hicks’ derivation might be a questionable approach. Further investigations are necessary to explore different approaches that will properly close the equation system without leading to unphysical behaviors.

42 ENGINEERING↗

SOLVING CONJUGATE HEAT TRANSFER PROBLEM IN TWO-PHASE FLOW USING NEWTON-KRYLOV METHOD

In this paper, we successfully demonstrated an application of the Jacobian-free Newton Krylov (JFNK) method in solving the conjugated two-phase channel flow and heat conduction problem, in a fully coupled and fully implicit manner. Such a problem represents the most fundamental piece of safety analysis codes, for example the heat transfer between fuel rods and reactor coolant during postulated accidental scenarios. The two-phase flow is modeled with the widely accepted one-dimensional two-fluid two-phase flow model, and the heat conduction is modeled with two-dimensional heat conduction model. The coupling between these two physics is realized through the wall heat transfer term in fluid equations and heat flux boundary conditions of heat conduction model. For spatial discretization, both the first-order and second- order upwind schemes are considered for flow equations, while the standard central differencing method is used for the heat conduction model. For time integration, both the first-order backward Euler (BDF1) and second-order BDF2 schemes are considered. Several treatments were also introduced to enhance the robustness of the JFNK method in solving such a problem that is discontinuous in nature because of the discrete closure correlations. These treatments include the re-introduction of a transition region between the slug and annular mist flow regimes, and a simplification in the interfacial drag term. Numerical results have been extensively validated with experimental data in both vertical pipe and rod bundle geometries with a wide range of thermal-hydraulics conditions, including pressure, inlet subcooling, wall heat flux, outlet void fraction, and etc. Further benchmark with the RELAP5-3D code confirms the correct implementation of wall heat transfer models.

42 ENGINEERING↗

SINGLE PHASE ANALYTICAL MODELS FOR TERRY TURBINE NOZZLE

All BWR RCIC (Reactor Core Isolation Cooling) systems and PWR AFW (Auxiliary Feed Water) systems use Terry turbine, which is composed of the wheel with turbine buckets and several groups of fixed nozzles and reversing chambers inside the turbine casing. The inlet steam is accelerated through the turbine nozzle and impacts on the wheel buckets, generating work to drive the RCIC pump. As part of the efforts to understand the unexpected “self-regulating” mode of the RCIC systems in Fukushima accidents and extend BWR RCIC and PWR AFW operational range and flexibility, mechanistic models for the Terry turbine, based on Sandia National Laboratories’ original work, has been developed and implemented in the RELAP-7 code to simulate the RCIC system. RELAP-7 is a new reactor system code currently under development with the funding support from U.S. Department of Energy. The RELAP-7 code is a fully implicit code and the preconditioned Jacobian-free Newton-Krylov (JFNK) method is used to solve the discretized nonlinear system. This paper presents a set of analytical models for simulating the flow through the Terry turbine nozzles when inlet fluid is pure steam. The implementation of the models into RELAP-7 will be briefly discussed. In the Sandia model, the turbine bucket inlet velocity is provided according to a reduced-order model, which was obtained from a large number of CFD simulations. In this work, we propose an alternative method, using an under-expanded jet model to obtain the velocity and thermodynamic conditions for the turbine bucket inlet. The models include both adiabatic expansion process inside the nozzle and free expansion process out of the nozzle to reach the ambient pressure. The combined models are able to predict the steam mass flow rate and supersonic velocity to the Terry turbine bucket entrance, which are the necessary input conditions for the Terry Turbine rotor model. The nozzle analytical models were validated with experimental data and benchmarked with CFD simulations. The analytical models generally agree well with the experimental data and CFD simulations. The analytical models are suitable for implementation into a reactor system analysis code or severe accident code as part of mechanistic and dynamical models to understand the RCIC behaviors. The cases with two-phase flow at the turbine inlet will be pursued in future work.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Comparisons of Wilks’ and Monte Carlo Methods in Response to the 10CFR50.46(c) Proposed Rulemaking

The Nuclear Regulatory Commission (NRC) is proposing a new rulemaking on emergency core system/loss-of-coolant accident (LOCA) performance analysis. In the proposed rulemaking, designated as 10CFR50.46(c), the US NRC put forward an equivalent cladding oxidation criterion as a function of cladding pre-transient hydrogen content. The proposed rulemaking imposes more restrictive and burnup-dependent cladding embrittlement criteria; consequently nearly all the fuel rods in a reactor core need to be analyzed under LOCA conditions to demonstrate compliance to the safety limits. New analysis methods are required to provide a thorough characterization of the reactor core in order to identify the locations of the limiting rods as well as to quantify the safety margins under LOCA conditions. With the new analysis method presented in this work, the limiting transient case and the limiting rods can be easily identified to quantify the safety margins in response to the proposed new rulemaking. In this work, the best-estimate plus uncertainty (BEPU) analysis capability for large break LOCA with the new cladding embrittlement criteria using the RELAP5-3D code is established and demonstrated with a reduced set of uncertainty parameters. Both the direct Monte Carlo method and the Wilks’ nonparametric statistical method can be used to perform uncertainty quantification. Wilks’ method has become the de-facto industry standard to perform uncertainty quantification in BEPU LOCA analyses. Despite its widespread adoption by the industry, the use of small sample sizes to infer statement of compliance to the existing 10CFR50.46 rule, has been a major cause of unrealized operational margin in today’s BEPU methods. Moreover the debate on the proper interpretation of the Wilks’ theorem in the context of safety analyses is not fully resolved yet, even more than two decades after its introduction in the frame of safety analyses in the nuclear industry. This represents both a regulatory and application risk in rolling out new methods. With the 10CFR50.46(c) proposed rulemaking, the deficiencies of the Wilks’ approach are further exacerbated. The direct Monte Carlo approach offers a robust alternative to perform uncertainty quantification within the context of BEPU analyses. In this work, the Monte Carlo method is compared with the Wilks’ method in response to the NRC 10CFR50.46(c) proposed rulemaking.

10CFR50.46(c)↗

Best estimate plus uncertainty analysis of departure from nucleate boiling limiting case with CASL core simulator VERA-CS in response to PWR main steam line break event

VERA-CS (Virtual Environment for Reactor Applications, Core Simulator) is a coupled neutron transport and thermal-hydraulics subchannel code under development by the Consortium for Advanced Simulation of Light Water Reactors (CASL). VERA-CS was used to simulate a typical pressurized water reactor (PWR) full core response with 17x17 fuel assemblies for a main steam line break (MSLB) accident scenario with the most reactive rod cluster control assembly stuck out of the core. The accident scenario was initiated at the hot zero power (HZP) at the end of the first fuel cycle with return to power state points that were determined by a system analysis code and the most limiting state point was chosen for core analysis. The best estimate plus uncertainty (BEPU) analysis method was applied using Wilks’ nonparametric statistical approach. In this way, 59 full core simulations were performed to provide the minimum departure from nucleate boiling ratio (MDNBR) at the 95/95 (95% probability with 95% confidence level) tolerance limit. The results show that this typical PWR core remains within MDNBR safety limits for the MSLB accident.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Development and Implementation of Mechanistic Terry Turbine Models in RELAP-7 to Simulate RCIC Normal Operation Conditions

As part of the efforts to understand the unexpected “self-regulating” mode of the RCIC (Reactor Core Isolation Cooling) systems in Fukushima accidents and extend BWR RCIC and PWR AFW (Auxiliary Feed Water) operational range and flexibility, mechanistic models for the Terry turbine, based on Sandia’s original work [1], have been developed and implemented in the RELAP-7 code to simulate the RCIC system. In 2016, our effort has been focused on normal working conditions of the RCIC system. More complex off-design conditions will be pursued in later years when more data are available. In the Sandia model, the turbine stator inlet velocity is provided according to a reduced-order model which was obtained from a large number of CFD (computational fluid dynamics) simulations. In this work, we propose an alternative method, using an under-expanded jet model to obtain the velocity and thermodynamic conditions for the turbine stator inlet. The models include both an adiabatic expansion process inside the nozzle and a free expansion process outside of the nozzle to ambient pressure. The combined models are able to predict the steam mass flow rate and supersonic velocity to the Terry turbine bucket entrance, which are the necessary input information for the Terry turbine rotor model. The analytical models for the nozzle were validated with experimental data and benchmarked with CFD simulations. The analytical models generally agree well with the experimental data and CFD simulations. The analytical models are suitable for implementation into a reactor system analysis code or severe accident code as part of mechanistic and dynamical models to understand the RCIC behaviors. The newly developed nozzle models and modified turbine rotor model according to the Sandia’s original work have been implemented into RELAP-7, along with the original Sandia Terry turbine model. A new pump model has also been developed and implemented to couple with the Terry turbine model. An input model was developed to test the Terry turbine RCIC system, which generates reasonable results. Both the INL RCIC model and the Sandia RCIC model produce results matching major rated parameters such as the rotational speed, pump torque, and the turbine shaft work for the normal operation condition. The Sandia model is more sensitive to the turbine outlet pressure than the INL model. The next step will be further refining the Terry turbine models by including two-phase flow cases so that off-design conditions can be simulated. The pump model could also be enhanced with the use of the homologous curves.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Numerical implementation, verification and validation of two-phase flow four-equation drift flux model with Jacobian-free Newton–Krylov method

This study presents a numerical investigation on using the Jacobian-free Newton–Krylov (JFNK) method to solve the two-phase flow four-equation drift flux model with realistic constitutive correlations (‘closure models’). The drift flux model is based on Isshi and his collaborators’ work. Additional constitutive correlations for vertical channel flow, such as two-phase flow pressure drop, flow regime map, wall boiling and interfacial heat transfer models, were taken from the RELAP5-3D Code Manual and included to complete the model. The staggered grid finite volume method and fully implicit backward Euler method was used for the spatial discretization and time integration schemes, respectively. The Jacobian-free Newton–Krylov method shows no difficulty in solving the two-phase flow drift flux model with a discrete flow regime map. In addition to the Jacobian-free approach, the preconditioning matrix is obtained by using the default finite differencing method provided in the PETSc package, and consequently the labor-intensive implementation of complex analytical Jacobian matrix is avoided. Extensive and successful numerical verification and validation have been performed to prove the correct implementation of the models and methods. Code-to-code comparison with RELAP5-3D has further demonstrated the successful implementation of the drift flux model.

42 ENGINEERING↗

Implementation and validation of a fully implicit accumulator model in RELAP-7

This paper presents the implementation and validation of an accumulator model in RELAP-7 under the framework of preconditioned Jacobian free Newton Krylov (JFNK) method, based on the similar model used in RELAP5. RELAP-7 is a new nuclear reactor system safety analysis code being developed at the Idaho National Laboratory (INL). RELAP-7 is a fully implicit system code. The JFNK and preconditioning methods used in RELAP-7 is briefly discussed. The slightly modified accumulator model is summarized for completeness. The implemented model was validated with LOFT L3-1 test and benchmarked with RELAP5 results. RELAP-7 and RELAP5 had almost identical results for the accumulator gas pressure and water level, although there were some minor difference in other parameters such as accumulator gas temperature and tank wall temperature. One advantage of the JFNK method is its easiness to maintain and modify models due to fully separation of numerical methods from physical models. It would be straightforward to extend the current RELAP-7 accumulator model to simulate the advanced accumulator design. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

limiting rods selection in large break LOCA analysis with the RELAP5-3D code

The Nuclear Regulatory Commission (NRC) is proposing a new rulemaking on emergency core system/loss-of-coolant accident (LOCA) performance analysis. In the proposed rulemaking, designated as 10 CFR 50.46(c), the US NRC put forward an equivalent cladding oxidation criterion as a function of cladding pre-transient hydrogen content. The proposed rulemaking imposes more restrictive and burnup-dependent cladding embrittlement criteria; consequently more fuel rods need to be analyzed under LOCA conditions to maintain the safety margin, compared to the current practice in which only one hot rod needs to be analyzed. New analysis methods are required to provide a thorough characterization of the reactor core in order to identify the locations of the limiting rods under LOCA conditions. In this work, the best-estimate plus uncertainty analysis capability for large break LOCA with the new cladding embrittlement criteria using the RELAP5-3D code is established and demonstrated with a reduced set of uncertainty parameters. With the new analysis method, the limiting transient case and the limiting rods can be easily identified in response to the proposed new rulemaking. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

RISMC Analysis Framework in Response to Proposed 10 CFR 50.46c Rulemaking

The results obtained from the demonstration calculations indicate that as an automation tool in LOCA analyses, LOTUS has the capability to provide integrated evaluation through seamless interfaces of the data stream in multiple disciplines. With further more development, LOTUS will provide a systematic way to perform uncertainty quantification, sensitivity analysis and risk assessment of the multiple physics involved in the LOCA analysis in response to the proposed 10 CFR 50.46c rulemaking. It can be used to obtain quantitative estimate of design or operational margin loss or gain as well as to assess the impact on LOCA analysis safety metrics associated with various combinations of changes in LOCA analysis inputs. It can also aid plant owners to make decision on evaluating design changes as well as resolving operational issues. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Analytical Models for Terry Turbine Nozzle

As part of the efforts to understand the unexpected 'self-regulating' mode of the RCIC (Reactor Core Isolation Cooling) systems in Fukushima accidents and extend BWR RCIC and PWR AFW (Auxiliary Feed Water) operational range and flexibility, mechanistic models for the Terry turbine should be developed and implemented in reactor system analysis or severe accident codes. The Terry turbine has been used for all the BWR RCIC systems and for PWR AFW (Auxiliary Feed Water) systems. The Terry turbine is essentially a solid cylindrical wheel with multiple machined semi-circular 'buckets' that are shaped into the body of the wheel. Fixed nozzles and reversing chambers surround the wheel inside the turbine casing. High pressure steam is accelerated to supersonic flow inside the turbine nozzle. The kinetic energy is then converted to shaft work by the impulse force on the turbine buckets. A Fully implicit and strongly coupled RCIC system model has been developed in the RELAP-7 code and used for simplified BWR SBO (Station Black-Out) simulations in the past. In this model, a generic turbine model was used to conserve mass and energy while turbine operation characteristic curves were used to obtain non-dimensional mass flow rate and thermal efficiency. This model could be used for simulating RCIC off-design behavior if off-design operation characteristic curves were available. However, No such curves currently exist for the Terry turbine system due to its unique pure impulse design. A set of mechanistic Terry turbine models suitable for system code implementation has recently been developed by Sandia National Labs. In the Sandia model, the turbine bucket inlet velocity is provided according to a reduced-order model which was obtained from a large number of CFD simulations. In this paper, we propose an alternative method, using an under-expanded jet model to obtain the velocity and thermodynamic conditions for the turbine bucket inlet. These sets of analytical models are simple and generic, and suitable for use in system analysis codes. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

New analytical solutions to the two-phase water faucet problem

Here, the one-dimensional water faucet problem is one of the classical benchmark problems originally proposed by Ransom to study the two-fluid two-phase flow model. With certain simplifications, such as massless gas phase and no wall and interfacial frictions, analytical solutions had been previously obtained for the transient liquid velocity and void fraction distribution. The water faucet problem and its analytical solutions have been widely used for the purposes of code assessment, benchmark and numerical verifications. In our previous study, the Ransom’s solutions were used for the mesh convergence study of a high-resolution spatial discretization scheme. It was found that, at the steady state, an anticipated second-order spatial accuracy could not be achieved, when compared to the existing Ransom’s analytical solutions. A further investigation showed that the existing analytical solutions do not actually satisfy the commonly used two-fluid single-pressure two-phase flow equations. In this work, we present a new set of analytical solutions of the water faucet problem at the steady state, considering the gas phase density’s effect on pressure distribution. This new set of analytical solutions are used for mesh convergence studies, from which anticipated second-order of accuracy is achieved for the 2nd order spatial discretization scheme. In addition, extended Ransom’s transient solutions for the gas phase velocity and pressure are derived, with the assumption of decoupled liquid and gas pressures. Numerical verifications on the extended Ransom’s solutions are also presented.

97 MATHEMATICS AND COMPUTING↗

RISMC Industry Application no. 1 (ECCS/LOCA) - Core Characterization Automation: Lattice Codes Interface for PHISICS/RELAP5-3D

The U.S. NRC is currently proposing rulemaking '10 CFR 50.46c' to revise the loss-of-coolant-accident (LOCA) and emergency core cooling system (ECCS) acceptance criteria to include the effects of higher burn-up on cladding performance. The key implications of this proposition are that the cladding performance cannot be evaluated in isolation anymore. Both cladding and ECCS performance need to be considered in a coupled manner. This also implies that models for cladding performance as well as LOCA methodologies will need to be updated for regulatory purposes. Furthermore, efforts need to be made to find the limiting case within the regulatory input space. The Risk-Informed Safety Margin Characterization (RISMC) Pathway, as part of the DOE Light Water Reactor Sustainability (LWRS) research and development program initialed several programs at the Idaho National Laboratory (INL) to support the industry in the transition to the new rule and to offer potential solutions to this LOCA/ECCS analysis. One of these programs is the Industry Application no. 1 (IA1). Its purpose is to provide to the plant owner/operator a vehicle to inform decisions to manage margins related to compliance with the proposed 10 CFR 50.46c rule. IA1's goal is to develop an Integrated Evaluation Model (IEM) to revisit how uncertainties are propagated across the physical disciplines and data involved, as well as well as how risks are evaluated in a LOCA under 10 CFR 50.46c. This IEM is called LOCA Tool-kit for the US (LOTUS) and it connects five major disciplines involved in LOCA analysis. The focus of LOTUS is to establish the automation interfaces among the five disciplines. LOTUS will utilize in a first step existing computer codes. The risk-informed margins management approach for IA1 will provide a means of quantifying the impact on the key LOCA analysis figures-of-merit like peak cladding temperature (PCT), equivalent cladding reacted (ECR), etc. of a change in LOCA analysis inputs. The information that the risk analysis and associated tools provide can then be used for decision-making and margin management. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Solving Drift-flux Model Using High-Resolution Spatial Discretization Scheme

Accurate modeling and simulation of the two-phase flow phenomena are critical to the system and safety analysis of light water reactors. Compared to the more complex two-fluid model, the drift-flux model treats the two phases as a mixture, and thus the models are formulated to consider the conservation laws of the mixture. The relative motion between the two phases is realized by constitutive correlations. Although the drift flux models have limitations in certain applications, they are widely used in many applications due to their simplicity and applicability to a wide range of two-phase flow problems. First-order numerical schemes are widely used in existing codes, which introduces excessive numerical diffusions. The objective of this work is to investigate a high-resolution spatial scheme in the application to solve drift-flux two-phase flow problems. In this study, a high-resolution spatial discretization scheme has been investigated in the application of solving drift-flux two-phase flow problem. The scheme is validated using existing experimental results. Compared to the first order scheme, it demonstrated excellent capability in reducing numerical error. Extended work will focus on the comparison of numerical errors from discretization schemes and model uncertainties. (authors)

42 ENGINEERING↗

Uncertainty quantification and sensitivity analysis with CASL Core Simulator VERA-CS

Uncertainty quantification and sensitivity analysis are important for nuclear reactor safety design and analysis. A 2x2 fuel assembly core design was developed and simulated by the Virtual Environment for Reactor Applications, Core Simulator (VERA-CS) coupled neutronics and thermal-hydraulics code under development by the Consortium for Advanced Simulation of Light Water Reactors (CASL). An approach to uncertainty quantification and sensitivity analysis with VERA-CS was developed and a new toolkit was created to perform uncertainty quantification and sensitivity analysis with fourteen uncertain input parameters. Furthermore, the minimum departure from nucleate boiling ratio (MDNBR), maximum fuel center-line temperature, and maximum outer clad surface temperature were chosen as the selected figures of merit. Pearson, Spearman, and partial correlation coefficients were considered for all of the figures of merit in sensitivity analysis and coolant inlet temperature was consistently the most influential parameter. We used parameters as inputs to the critical heat flux calculation with the W-3 correlation were shown to be the most influential on the MDNBR, maximum fuel center-line temperature, and maximum outer clad surface temperature.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Solving phase appearance/disappearance two-phase flow problems with high resolution staggered grid and fully implicit schemes by the Jacobian-free Newton–Krylov Method

The phase appearance/disappearance issue presents serious numerical challenges in two-phase flow simulations. Many existing reactor safety analysis codes use different kinds of treatments for the phase appearance/disappearance problem. However, to our best knowledge, there are no fully satisfactory solutions. Additionally, the majority of the existing reactor system analysis codes were developed using low-order numerical schemes in both space and time. In many situations, it is desirable to use high-resolution spatial discretization and fully implicit time integration schemes to reduce numerical errors. In this work, we adapted a high-resolution spatial discretization scheme on staggered grid mesh and fully implicit time integration methods (such as BDF1 and BDF2) to solve the two-phase flow problems. The discretized nonlinear system was solved by the Jacobian-free Newton Krylov (JFNK) method, which does not require the derivation and implementation of analytical Jacobian matrix. These methods were tested with a few two-phase flow problems with phase appearance/disappearance phenomena considered, such as a linear advection problem, an oscillating manometer problem, and a sedimentation problem. The JFNK method demonstrated extremely robust and stable behaviors in solving the two-phase flow problems with phase appearance/disappearance. No special treatments such as water level tracking or void fraction limiting were used. High-resolution spatial discretization and second- order fully implicit method also demonstrated their capabilities in significantly reducing numerical errors.

97 MATHEMATICS AND COMPUTING↗

R&D Plan for RISMC Industry Application #1: ECCS/LOCA Cladding Acceptance Criteria

The Nuclear Regulatory Commission (NRC) is finalizing a rulemaking change that would revise the requirements in 10 CFR 50.46. In the proposed new rulemaking, designated as 10 CFR 50.46c, the NRC proposes a fuel performance-based equivalent cladding reacted (ECR) criterion as a function of cladding hydrogen content before the accident (pre-transient) in order to include the effects of higher burnup on cladding performance as well as to address other technical issues. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee costs as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. The Idaho National Laboratory (INL) has initiated a project, as part of the DOE Light Water Reactor Sustainability Program (LWRS), to develop analytical capabilities to support the industry in the transition to the new rule. This project is called the Industry Application 1 (IA1) within the Risk-Informed Safety Margin Characterization (RISMC) Pathway of LWRS. The general idea behind the initiative is the development of an Integrated Evaluation Model (IEM). The motivation is to develop a multiphysics framework to analyze how uncertainties are propagated across the stream of physical disciplines and data involved, as well as how risks are evaluated in a LOCA safety analysis as regulated under 10 CFR 50.46c. This IEM is called LOTUS which stands for LOCA Toolkit for US, and it represents the LWRS Program’s response to the proposed new rule making. The focus of this report is to complete an R&D plan to describe the demonstration of the LOCA/ECCS RISMC Industry Application # 1 using the advanced RISMC Toolkit and methodologies. This report includes the description and development plan for a RISMC LOCA tool that fully couples advanced MOOSE tools already in development in order to characterize and optimize plant safety and operational margins. Advanced MOOSE tools that are needed to complete this integrated evaluation model are: RAVEN, RELAP-7, BISON, and MAMMOTH.

10CFR50.46C↗